LiftMaster 970LM Manual

LiftMaster Ikke kategoriseret 970LM

Læs gratis den danske manual til LiftMaster 970LM (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om LiftMaster 970LM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Single Button Remote Control 3-Button Remote Control Mini-Remote Control

SECURITY+® REMOTE CONTROLS

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play

with remote controls.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no

obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross

path of moving gate or door.

Press and hold the button

on the remote control

that you wish to operate

your door.

“click”

Release the

button when the

garage door

opener lights

blink or two

clicks are heard.

Locate the

Smart/Learn

button on

the garage

..renepo rood

Press and

immediately release

the learn button.

The learn LED will glow

steadily for 30 seconds.

Within 30 seconds...

PROGRAMMING THE REMOTE CONTROL

Press and hold the learn button

on garage door opener until the

learn LED goes out (approximately

6 seconds). All previous codes

are now erased.

For use with 390 MHz Security+® garage door openers and light controls that have an learn orange

button. The code between the remote control and the receiver changes with each use, randomly

accessing over a billion new codes.

NOTE: Your products may look different than the products illustrated in this manual.

TO CONTROL THE GARAGE DOOR OPENER LIGHTS

With the door closed,

press and hold

the remote

control button

that you want to

control the light.

LIG

Press and

hold the

light button

on the

door control.

LIG T

Press and

hold the

lock button

on the

door control.

After the garage

door opener

lights ﬂash,

release all

buttons.

2 3

“click”

This feature is only available on garage door openers equipped with a multi-function door control and a remote control with more than one button. Not available with universal receiver.

With Security+

® remote controls, a remote control button can be programmed to operate the garage door opener lights without opening the door.

Reprogram each remote control you wish to use.

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov

TO ERASE ALL CODES FROM MEMORY

To deactivate any unwanted remote control, first erase all codes:

Test by pressing the remote control button. The garage door opener lights should turn on or off but the door should not move.

THE REMOTE CONTROL BATTERY

1Use the visor clip or

screwdriver to pry open

the cover.

2Remove the old battery. Dispose

of old batteries properly.

3Insert replacement batteries

positive side up. Replace the

batteries with

only 3V CR2032

coin cell

batteries.

4Replace cover.

The lithium battery should produce power for up to 3 years. To replace battery:

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

• Replace ONLY with 3V CR2032 coin batteries.

• DO NOT recharge, disassemble, heat above 212°F

(100°C) or incinerate.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing

the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

REPLACEMENT PARTS