Lincoln Electric Easy MIG 140 Manual

Lincoln Electric Ikke kategoriseret Easy MIG 140

Læs gratis den danske manual til Lincoln Electric Easy MIG 140 (124 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Lincoln Electric Easy MIG 140, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/124
Operator’s Manual
WIRE FEEDER WELDERS (125, 140 MODELS)
Register your machine:
www.lincolnelectric.com/register
Authorized Service and Distributor Locator:
www.lincolnelectric.com/locator
IM10049-B | Issue D ate Oct- 19
© Lincoln Global, Inc. All Rights Reserved.
For use with machines having Code Numbers:
11631, 11632, 11633, 11634,
11635, 11636, 11637, 11638,
11639, 12100, 12101, 12102,
12103, 12104, 12105, 12106,
12107, 12191, 12192
Save for future reference
Date Purchased
Code: (ex: 10859)
Serial: (ex: U1060512345)
OPERATOR’S MANUAL
MANUAL DE OPERACIÓN
MANUEL DE L’OPÉRATEUR
THANK YOU FOR SELECTING
A QUALITY PRODUCT BY
LINCOLN ELEC TRIC.
PLEASE EXAMINE CARTON AND EQUIPMENT FOR
DAMAGE IMMEDIATELY
When this equipment is shipped, title passes to the purchaser
upon receipt by the carrier. Consequently, claims for material
damaged in shipment must be made by the purchaser against the
transportation company at the time the shipment is received.
SAFETY DEPENDS ON YOU
Lincoln arc welding and cutting equipment is designed and built
with safety in mind. However, your overall safety can be increased
by proper installation ... and thoughtful operation on your part.
DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT
WITHOUT READING THIS MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly,
think before you act and be careful.
This statement appears where the information must be followed
exactly to avoid serious personal injury or loss of life.
This statement appears where the information must be followed
to avoid minor personal injury or damage to this equipment.
KEEP YOUR HEAD OUT OF THE FUMES.
DON’T get too close to the arc.
Use corrective lenses if necessary
to stay a reasonable distance
away from the arc.
READ and obey the Safety Data
Sheet (SDS) and the warning label
that appears on all containers of
welding materials.
USE ENOUGH VENTILATION or
exhaust at the arc, or both, to
keep the fumes and gases from
your breathing zone and the general area.
IN A LARGE ROOM OR OUTDOORS, natural ventilation may be
adequate if you keep your head out of the fumes (See below).
USE NATURAL DRAFTS or fans to keep the fumes away
from your face.
If you de velop unusual symptoms, see your supervisor.
Perhaps the welding atmosphere and ventilation system
should be checked.
WEAR CORRECT EYE, EAR &
BODY PROTECTION
PROTECT your eyes and face with welding helmet
properly fitted and with proper grade of filter plate
(See ANSI Z49.1).
PROTECT your body from welding spatter and arc
flash with protective clothing including woolen
clothing, flame-proof apron and gloves, leather
leggings, and high boots.
PROTECT others from splatter, flash, and glare
with protective screens or barriers.
IN SOME AREAS, protection from noise may be appropriate.
BE SURE protective equipment is in good condition.
Also, wear safety glasses in work area
AT ALL TIMES.
SPECIAL SITUATIONS
DO NOT WELD OR CUT containers or materials which previously
had been in contact with hazardous substances unless they are
properly cleaned. This is extremely dangerous.
DO NOT WELD OR CUT painted or plated parts unless special
precautions with ventilation have been taken. They can release
highly toxic fumes or gases.
Additional precautionary measures
PROTECT compressed gas cylinders from excessive heat,
mechanical shocks, and arcs; fasten cylinders so they cannot fall.
BE SURE cylinders are never grounded or part of an
electrical circuit.
REMOVE all potential fire hazards from welding area.
ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR
IMMEDIATE USE AND KNOW HOW TO USE IT.
WARNING
CAUTION
Safety 01 of 04 - 5/16/2018

Produkt Specifikationer

Mærke: Lincoln Electric
Kategori: Ikke kategoriseret
Model: Easy MIG 140

Har du brug for hjælp?

Hvis du har brug for hjælp til Lincoln Electric Easy MIG 140 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Lincoln Electric Manualer

Lincoln Electric

Lincoln Electric Easy MIG 140 Manual

23 September 2025
Lincoln Electric

Lincoln Electric Magnum Pro 100SG Manual

23 September 2025
Lincoln Electric

Lincoln Electric Utility Cart Manual

23 September 2025
Lincoln Electric

Lincoln Electric Master Load 750 Manual

8 September 2025
Lincoln Electric

Lincoln Electric LINCGUN PROMIG AIR Manual

8 September 2025
Lincoln Electric

Lincoln Electric OMNIShield Faceshield Manual

7 September 2025
Lincoln Electric

Lincoln Electric Linc-Cut 3015 CNC Fiber Laser Manual

20 Juli 2025
Lincoln Electric

Lincoln Electric POWER MIG 255XT Manual

19 Juli 2025
Lincoln Electric

Lincoln Electric LINCGUN PROMIG AIR 230T Manual

14 Marts 2025
Lincoln Electric

Lincoln Electric LINCGUN PROMIG WATER 330W Manual

14 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Chefman

Chefman RJ16-LOCK Manual

23 September 2025
Prebena

Prebena ST2-ANK50 Manual

23 September 2025
T'nB

T'nB CHNB19V90 Manual

23 September 2025
Valcom

Valcom V-6120 Manual

23 September 2025
T'nB

T'nB ACGP7IN1V2 Manual

23 September 2025
Prebena

Prebena KTVH-B19H Manual

23 September 2025
T'nB

T'nB CHCAR15W Manual

23 September 2025
Miele

Miele GDU 60/60-7 Manual

23 September 2025
Prebena

Prebena 2M-GA32SDS Manual

23 September 2025
Crestron

Crestron TPS-4LW Manual

23 September 2025