Lincoln Electric Flex Feed 84 Manual

Lincoln Electric Ikke kategoriseret Flex Feed 84

Læs gratis den danske manual til Lincoln Electric Flex Feed 84 (76 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Lincoln Electric Flex Feed 84, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/76
IM10189-A | Issue Date Jun - 21
© Lincoln Global, Inc. All Rights Reserved.
Operator’s Manual
Register your machine:
www.lincolnelectric.com/register
Authorized Service and Distributor Locator:
www.lincolnelectric.com/locator
For use with machines having Code Numbers:
Flex Feed 84: 12251, 12252,
12253, 12544, 13033, 13034,
13035, 13040
Flex Feed 84 Dual: 12258,
12259, 12262, 12545, 13036,
13037, 13038, 13041
Flex Feed 84 Control Box:
12271, 13039
Save for future reference
Date Purchased
Code: (ex: 10859)
Serial: (ex: U1060512345)
Flex Feed ™ 84, Flex Feed ™ 84 Dual
THANK YOU FOR SELECTING
A QUALITY PRODUCT BY
LINCOLN ELEC TRIC.
PLEASE EXAMINE CARTON AND EQUIPMENT FOR
DAMAGE IMMEDIATELY
When this equipment is shipped, title passes to the purchaser
upon receipt by the carrier. Consequently, claims for material
damaged in shipment must be made by the purchaser against the
transportation company at the time the shipment is received.
SAFETY DEPENDS ON YOU
Lincoln arc welding and cutting equipment is designed and built
with safety in mind. However, your overall safety can be increased
by proper installation ... and thoughtful operation on your part.
DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT
WITHOUT READING THIS MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly,
think before you act and be careful.
This statement appears where the information must be followed
exactly to avoid serious personal injury or loss of life.
This statement appears where the information must be followed
to avoid minor personal injury or damage to this equipment.
KEEP YOUR HEAD OUT OF THE FUMES.
DON’T get too close to the arc.
Use corrective lenses if necessary
to stay a reasonable distance
away from the arc.
READ and obey the Safety Data
Sheet (SDS) and the warning label
that appears on all containers of
welding materials.
USE ENOUGH VENTILATION or
exhaust at the arc, or both, to
keep the fumes and gases from
your breathing zone and the general area.
IN A LARGE ROOM OR OUTDOORS, natural ventilation may be
adequate if you keep your head out of the fumes (See below).
USE NATURAL DRAFTS or fans to keep the fumes away
from your face.
If you de velop unusual symptoms, see your supervisor.
Perhaps the welding atmosphere and ventilation system
should be checked.
WEAR CORRECT EYE, EAR &
BODY PROTECTION
PROTECT your eyes and face with welding helmet
properly fitted and with proper grade of filter plate
(See ANSI Z49.1).
PROTECT your body from welding spatter and arc
flash with protective clothing including woolen
clothing, flame-proof apron and gloves, leather
leggings, and high boots.
PROTECT others from splatter, flash, and glare
with protective screens or barriers.
IN SOME AREAS, protection from noise may be appropriate.
BE SURE protective equipment is in good condition.
Also, wear safety glasses in work area
AT ALL TIMES.
SPECIAL SITUATIONS
DO NOT WELD OR CUT containers or materials which previously
had been in contact with hazardous substances unless they are
properly cleaned. This is extremely dangerous.
DO NOT WELD OR CUT painted or plated parts unless special
precautions with ventilation have been taken. They can release
highly toxic fumes or gases.
Additional precautionary measures
PROTECT compressed gas cylinders from excessive heat,
mechanical shocks, and arcs; fasten cylinders so they cannot fall.
BE SURE cylinders are never grounded or part of an
electrical circuit.
REMOVE all potential fire hazards from welding area.
ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR
IMMEDIATE USE AND KNOW HOW TO USE IT.
WARNING
CAUTION
Safety 01 of 04 - 5/16/2018

Produkt Specifikationer

Mærke: Lincoln Electric
Kategori: Ikke kategoriseret
Model: Flex Feed 84

Har du brug for hjælp?

Hvis du har brug for hjælp til Lincoln Electric Flex Feed 84 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Lincoln Electric Manualer

Lincoln Electric

Lincoln Electric Linc-Cut 3015 CNC Fiber Laser Manual

20 Juli 2025
Lincoln Electric

Lincoln Electric POWER MIG 255XT Manual

19 Juli 2025
Lincoln Electric

Lincoln Electric LINCGUN PROMIG AIR 230T Manual

14 Marts 2025
Lincoln Electric

Lincoln Electric LINCGUN PROMIG WATER 330W Manual

14 Marts 2025
Lincoln Electric

Lincoln Electric VRTEX Engage Manual

11 Januar 2025
Lincoln Electric

Lincoln Electric CHAMELEON 3V0 Manual

4 Januar 2025
Lincoln Electric

Lincoln Electric Prism Wall Mount Manual

9 December 2024
Lincoln Electric

Lincoln Electric COOLERTIG 4 Manual

9 December 2024
Lincoln Electric

Lincoln Electric Oil Guardian Manual

9 December 2024
Lincoln Electric

Lincoln Electric Inferno Torch KH825 Manual

9 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman

Navman MY500XT Manual

1 August 2025
Navman

Navman FOCUS150 GPS Manual

1 August 2025
Scheppach

Scheppach TW1000 Manual

1 August 2025
Navman

Navman MiVue 750 WIFI Manual

1 August 2025
Navman

Navman MiVue Drive FHD Manual

1 August 2025
Midea

Midea MEC64 Manual

1 August 2025
Navman

Navman MY50T Manual

1 August 2025
Navman

Navman M100 Manual

1 August 2025
Navman

Navman MiVue 770 SAFETY Manual

1 August 2025
Navman

Navman MiVue 790 Manual

1 August 2025