Linksys WRT350N Manual
Læs nedenfor 📖 manual på dansk for Linksys WRT350N (38 sider) i kategorien Routere. Denne guide var nyttig for 22 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/38
USER GUIDE
Wireless-N
Gigabit Router with
Storage Link
Model No: WRT350N
About This Guide
i
Wireless-N Gigabit Router with Storage Link
About This Guide
Icon Descriptions
While reading through the User Guide you may see
various icons that call attention to specific items. Below is
a description of these icons:
NOTE: This check mark indicates that there is
a note of interest and is something that you
should pay special attention to while using the
product.
WARNING: This exclamation point indicates
that there is a caution or warning and it is
something that could damage your property or
product.
WEB: This globe icon indicates a noteworthy
website address or e-mail address.
Online Resources
Website addresses in this document are listed without
http:// in front of the address because most current web
browsers do not require it. If you use an older web browser,
you may have to add in front of the web address. http://
Resource Website
Linksys www.linksys.com
Linksys International www.linksys.com/international
Glossary www.linksys.com/glossary
Network Security www.linksys.com/security
Copyright and Trademarks
Linksys is a registered trademark or
trademark of Cisco Systems, Inc. and/
or its affiliates in the U.S. and certain
other countries. Copyright © 2007
Cisco Systems, Inc. All rights reserved.
Other brands and product names are
trademarks or registered trademarks
of their respective holders.
Chapter 1 Product Overview
1
Wireless-N Gigabit Router with Storage Link
Chapter 1:
Product Overview
Thank you for choosing the Wireless-N Gigabit Router
with Storage Link, which is four devices in one: a wireless
access point, which lets you connect to a wireless network;
a built-in 4-port full-duplex 10/100 switch to connect your
wired-Ethernet devices together; a router function that
lets your whole network share a high-speed cable or DSL
Internet connection; and a Storage Link that easily lets you
add gigabytes of storage space onto your network using
USB 2.0 hard drives, or plug in a USB flash disk to access
your portable data files. The built-in media server streams
music, video, and photos from the attached storage
device to any UPnP compatible media adapter. And you
can get to your files from anywhere in the world through
the Internet. You also get Wireless-N technology, which
can highly increase your range and speed.
Front Panel
Power (Green) The Power LED lights up and
will stay on while the Router is powered on.
Ethernet (Green) (Orange) The Ethernet LED
lights up green when the Router is connected
to a device through the Ethernet port. If the LED
is flashing, the Router is sending or receiving
data over that port. The Ethernet LED lights
up orange when it is connected to Gigabit and
green when it is connected to 10/100.
Internet (Green) (Orange) The Internet LED
lights up green when there is a connection
made through the Internet port. A flashing LED
indicates network activity over the Internet
port. The Ethernet LED lights up orange when
it is connected to Gigabit and green when it is
connected to 10/100.
USB (Green) The USB LED indicates when an
external USB hard drive or USB flash disk is
connected to the Router.
Wireless (Green) The Wireless LED lights up
when there is a wireless connection. If the LED
is flashing, the Router is sending or receiving
data over the wireless network.
Security (Green) The Security LED indicates
when wireless security is enabled.
Back Panel
USB The USB port connects your Router to a
USB storage device.
Internet The Internet port is where you will
connect your cable or DSL Internet connection.
1, 2, 3, 4 These Ethernet ports (1, 2, 3, 4) connect
the Router to PCs on your wired network and
other Ethernet network devices.
Reset There are two ways to reset the Router’s
factory defaults. Either press and hold the Reset
Button for approximately five seconds, or restore
the defaults from Administration > Factory
Defaults in the Router’s web-based utility.
Power The Power port is where you will
connect the power adapter.
Table of Contents
i
Wireless-N Gigabit Router with Storage Link
Chapter 1: Product Overview 1
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Chapter 2: Wireless Security Checklist 2
General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 3: Advanced Conguration 3
Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup > DDNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Setup > MAC Address Clone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setup > Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wireless > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Wireless > Wireless MAC Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Security > Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Security > VPN Passthrough. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Storage > Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Storage > Share. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Storage > Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Storage > Media Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Storage > FTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Access Restrictions > Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Applications and Gaming > Single Port Forwarding. . . . . . . . . . . . . . . . . . . . . . . .18
Applications and Gaming > Port Range Forwarding . . . . . . . . . . . . . . . . . . . . . . .18
Applications & Gaming > Port Range Triggering . . . . . . . . . . . . . . . . . . . . . . . . . .19
Applications and Gaming > DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Applications and Gaming > QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Administration > Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Status > Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Status > Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Table of Contents
ii
Wireless-N Gigabit Router with Storage Link
Appendix A: Troubleshooting 26
Appendix B: Specications 27
Appendix C: Warranty Information 28
Appendix D: Regulatory Information 29
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Avis d’Industrie Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Avis de non-responsabilité concernant les appareils sans l . . . . . . . . . . . . . . . . . .30
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Chapter 2 Wireless Security Checklist
3
Wireless-N Gigabit Router with Storage Link
Chapter 2:
Wireless Security Checklist
Wireless networks are convenient and easy to install, so
homes with high-speed Internet access are adopting them
at a rapid pace. Because wireless networking operates by
sending information over radio waves, it can be more
vulnerable to intruders than a traditional wired network.
Like signals from your cellular or cordless phones, signals
from your wireless network can also be intercepted. Since
you cannot physically prevent someone from connecting
to your wireless network, you need to take some additional
steps to keep your network secure.
1. Change the default wireless
network name or SSID
Wireless devices have a default wireless network name
or Service Set Identifier (SSID) set by the factory. This
is the name of your wireless network, and can be up
to 32 characters in length. Linksys wireless products
use linksys as the default wireless network name. You
should change the wireless network name to something
unique to distinguish your wireless network from other
wireless networks that may exist around you, but do not
use personal information (such as your Social Security
number) because this information may be available for
anyone to see when browsing for wireless networks.
2. Change the default password
For wireless products such as access points and routers,
you will be asked for a password when you want to change
their settings. These devices have a default password set
by the factory. The Linksys default password is . admin
Hackers know these defaults and may try to use them
to access your wireless device and change your network
settings. To thwart any unauthorized changes, customize
the device’s password so it will be hard to guess.
3. Enable MAC address filtering
Linksys routers give you the ability to enable Media Access
Control (MAC) address filtering. The MAC address is a
unique series of numbers and letters assigned to every
networking device. With MAC address filtering enabled,
wireless network access is provided solely for wireless
devices with specific MAC addresses. For example, you can
specify the MAC address of each computer in your home
so that only those computers can access your wireless
network.
4. Enable encryption
Encryption protects data transmitted over a wireless
network. Wi-Fi Protected Access (WPA/WPA2) and Wired
Equivalency Privacy (WEP) offer different levels of security
for wireless communication. Currently, devices that are
Wi-Fi certified are required to support WPA2, but are not
required to support WEP.
A network encrypted with WPA/WPA2 is more secure
than a network encrypted with WEP, because WPA/WPA2
uses dynamic key encryption. To protect the information
as it passes over the airwaves, you should enable the
highest level of encryption supported by your network
equipment.
WEP is an older encryption standard and may be the
only option available on some older devices that do not
support WPA.
General Network Security Guidelines
Wireless network security is useless if the underlying
network is not secure.
Password protect all computers on the network and •
individually password protect sensitive files.
Change passwords on a regular basis. •
Install anti-virus software and personal firewall •
software.
Disable file sharing (peer-to-peer). Some applications •
may open file sharing without your consent and/or
knowledge.
Additional Security Tips
Keep wireless routers, access points, or gateways away •
from exterior walls and windows.
Turn wireless routers, access points, or gateways •
off when they are not being used (at night, during
vacations).
Use strong passphrases that are at least eight characters •
in length. Combine letters and numbers to avoid using
standard words that can be found in the dictionary.
WEB: For more information on wireless
security, visit www.linksys.com/security
Chapter 3 Advanced Configuration
4
Wireless-N Gigabit Router with Storage Link
Chapter 3:
Advanced Configuration
After setting up the Router with the Setup Wizard (located
on the CD-ROM), the Router will be ready for use. However,
if you’d like to change its advanced settings, use the
Router’s web-based utility. This chapter describes each
web page of the utility and each page’s key functions. You
can access the utility via a web browser on a computer
connected to the Router.
The web-based utility has these main tabs: Setup, Wireless,
Security, Storage, Access Restrictions, Applications &
Gaming, Administration, and Status. Additional tabs will
be available after you click one of the main tabs.
NOTE: When first installing the Router, you
should use the Setup Wizard on the Setup
CD-ROM. If you want to configure advanced
settings, use this chapter to learn about the
web-based utility.
How to Access the Web-Based Utility
To access the web-based utility, launch the web browser on
your computer, and enter the Router’s default IP address,
192.168.1.1, in the field. Then, press Address Enter.
A password request screen will appear. (Non-Windows XP
users will see a similar screen.) Leave the field User name
blank. The first time you open the Web-based utility, use
the default password admin. (You can set a new password
from the Administration tab’s screen.) Click Management
OK to continue.
Password Screen
Setup > Basic Setup
The first screen that appears is the screen. This Basic Setup
allows you to change the Router’s general settings.
Setup > Basic Setup
Internet Setup
The Internet Setup section configures the Router to your
Internet connection. Most of this information can be
obtained through your ISP.
Internet Connection Type
Select the type of Internet connection your ISP provides
from the drop-down menu. The available types are:
Automatic Configuration - DHCP •
Static IP •
PPPoE •
PPTP •
L2TP •
Telstra Cable •
Automatic Configuration - DHCP
By default, the Router’s Internet Connection Type is set
to Automatic Configuration - DHCP, which should be
kept only if your ISP supports DHCP or you are connecting
through a dynamic IP address. (This option usually applies
to cable connections.)
Internet Connection Type > Automatic Configuration - DHCP
Chapter 3 Advanced Configuration
6
Wireless-N Gigabit Router with Storage Link
L2TP
L2TP is a service that applies to connections in Israel only.
Internet Connection Type > L2TP
Internet IP Address This is the IP address of the L2TP
Server. Your ISP will provide you with the IP Address you
need to specify here.
User Name and Password Enter the User Name and
Password provided by your ISP.
Connect on Demand: Max Idle Time You can configure
the Router to cut the Internet connection after it has been
inactive for a specified period of time (Max Idle Time). If
your Internet connection has been terminated due to
inactivity, Connect on Demand enables the Router to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select . In the field, Connect on Demand Max Idle Time
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is minutes5
Keep Alive: Redial Period If you select this option,
the Router will periodically check your Internet
connection. If you are disconnected, then the Router
will automatically re-establish your connection. To use
this option, select . In the field, Keep Alive Redial Period
you specify how often you want the Router to check
the Internet connection. The default Redial Period is
30 seconds.
Telstra Cable
Telstra Cable is a service that applies to connections in
Australia only.
Internet Connection Type > Telstra Cable
Internet IP Address This is the IP address of the Telstra
Cable. Your ISP will provide you with the IP Address you
need to specify here.
User Name and Password Enter the User Name and
Password provided by your ISP.
Optional Settings
Some of these settings may be required by your ISP. Verify
with your ISP before making any changes.
Optional Settings
Host Name/Domain Name These fields allow you to
supply a host and domain name for the Router. Some ISPs,
usually cable ISPs, require these names as identification.
You may have to check with your ISP to see if your
broadband Internet service has been configured with a
host and domain name. In most cases, leaving these fields
blank will work.
MTU MTU is the Maximum Transmission Unit. It specifies
the largest packet size permitted for Internet transmission.
Select Manual if you want to manually enter the largest
packet size that is transmitted. To have the Router select
the best MTU for your Internet connection, keep the
default setting, Auto.
Size When Manual is selected in the MTU field, this option
is enabled. Leave this value in the 1200 to 1500 range. The
default size depends on the Internet Connection Type:
DHCP, Static IP, or Telstra: •1500
PPPoE: •1492
PPTP or L2TP: •1460
Network Setup
The Network Setup section changes the settings on the
network connected to the Router’s Ethernet ports. Wireless
Setup is performed through the Wireless tab.
Router Address
This presents both the Router’s IP Address and Subnet
Mask, and URL Address as seen by your network. The
default Router IP address is 192.168.1.1 and URL address
is http://WRT350N.com.
Router IP Address
Network Address Server Settings (DHCP)
The settings allow you to configure the Router’s Dynamic
Host Configuration Protocol (DHCP) server function. The
Router can be used as a DHCP server for your network. A
DHCP server automatically assigns an IP address to each
computer on your network. If you choose to enable the
Chapter 3 Advanced Configuration
7
Wireless-N Gigabit Router with Storage Link
Router’s DHCP server option, make sure there is no other
DHCP server on your network.
Network Address Server Settings (DHCP)
DHCP Server DHCP is enabled by factory default. If you
already have a DHCP server on your network, or you don’t
want a DHCP server, then select (no other DHCP Disable
features will be available).
Starting IP Address Enter a value for the DHCP server to
start with when is
suing IP addresses. Because the Router’s
default IP address is 192.168.1.1, the Starting IP Address must
be 192.168.1.2 or greater, but smaller than 192.168.1.253.
The default Starting IP Address is 192.168.1.100
.
Maximum Number of DHCP Users Enter the maximum
number of PCs that you want the DHCP server to assign
IP addresses to. This number cannot be greater than 253.
The default is .50
Client Lease Time The Client Lease Time is the amount
of time a network user will be allowed connection to the
Router with their current dynamic IP address. Enter the
amount of time, in minutes, that the user will be “leased”
this dynamic IP address. After the time is up, the user will
be automatically assigned a new dynamic IP address. The
default is minutes, which means one day.0
Static DNS (1-3)
The Domain Name System (DNS) is how
the Internet translates domain or website names into
Internet addresses or URLs. Your ISP will provide you with at
least one DNS Server IP Address. If you wish to use another,
enter that IP Address in one of these fields. You can enter up
to three DNS Server IP Addresses here. The Router will use
these for quicker access to functioning DNS servers
.
WINS The Windows Internet Naming Service (WINS)
manages each PC’s interaction with the Internet. If you
use a WINS server, enter that server’s IP Address here.
Otherwise, leave this blank.
DHCP Reservation Click if you want DHCP Reservation
to assign a fixed local IP address to a MAC address.
DHCP Reservation
You will see a list of DHCP clients with the following
information: Client Name, Interface, IP Address, and MAC
Address. Click the Select checkbox to reserve a client’s IP
address. Then click .Add Clients
If you want to manually assign an IP address, enter the
client’s name in the field. Enter the IP Enter Client Name
address you want it to have in the field. Assign IP Address
Make sure the IP address is between the starting DHCP
server’s IP address and maximum number of DHCP users
range. Enter its MAC Address in the To This MAC Address
field. Click .Add
A list of DHCP clients and their fixed local IP addresses will
be displayed at the bottom of the screen. If you want to
remove a client from this list, click Remove.
When you finish your changes, click to Save Settings
save your changes. Click Cancel Changes to cancel your
changes. To view the most up-to-date information, click
Refresh. To exit this screen, click .Close
Time Setting
Select the time zone in which your network functions
from this drop-down menu. (You can even automatically
adjust for daylight saving time.)
Time Setting
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Chapter 3 Advanced Configuration
9
Wireless-N Gigabit Router with Storage Link
Clone Your PC’s MAC Clicking this button will clone the
MAC address of the computer you are using.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Setup > Advanced Routing
This screen is used to set up the Router’s advanced
functions. Operating Mode allows you to select the
type(s) of advanced functions you use. Dynamic Routing
automatically adjusts how packets travel on your network.
Static Routing sets up a fixed route to another network
destination.
Setup > Advanced Routing
Advanced Routing
NAT If this Router is hosting your network’s connection
to the Internet, select . If another Router exists Enable
on your network, select When NAT is disabled, Disable.
Dynamic Routing (RIP) will be available as an option.
Dynamic Routing
RIP This feature enables the Router to automatically
adjust to physical changes in the network’s layout and
exchange routing tables with the other router(s). The
Router determines the network packets’ route based on
the fewest number of hops between the source and the
destination. This feature is by default. Disabled
Static Routing
Select Route Entry number To set up a static route
between the Router and another network, select a
number from the drop-down list. (A static route is a pre-
determined pathway that network information must travel
to reach a specific host or network.) Enter the information
described below to set up a new static route. (Click Delete
This Entry to delete a static route.)
Enter Route Name Enter a name for the Route here,
using a maximum of 25 alphanumeric characters.
Destination LAN IP The Destination LAN IP is the address
of the remote network or host to which you want to assign
a static route.
Subnet Mask The Subnet Mask determines which
portion of a Destination LAN IP address is the network
portion, and which portion is the host portion.
Gateway This is the IP address of the gateway device that
allows for contact between the Router and the remote
network or host.
Interface This interface tells you whether the Destination
IP Address is on the LAN & Wireless (Ethernet and wireless
networks) or the WAN (Internet) .
Click Show Routing Table to view the Static Routes you
have already set up.
Routing Table
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > Basic Wireless Settings
The basic settings for wireless networking are set on this
screen.
Wireless > Basic Wireless Settings
Wireless Network
Network Mode If you have wireless devices in your
network, keep the default setting, . If you do Mixed
not have any wireless devices in your network, select
Disable.
Chapter 3 Advanced Configuration
10
Wireless-N Gigabit Router with Storage Link
Wireless Network Name (SSID) The SSID is the network
name shared among all points in a wireless network.
The SSID must be identical for all devices in the wireless
network. It is case-sensitive and must not exceed
32 characters (use any of the characters on the keyboard).
Make sure this setting is the same for all points in your
wireless network. For added security, you should change
the default SSID to a unique name.
Radio Band For best performance in a network using
Wireless-N, Wireless-G and Wireless-B devices, keep the
default, Wide - 40MHz Channel. For Wireless-G and
Wireless-B networking only, select Standard - 20MHz
Channel.
Wide Channel If you selected Wide - 40MHz Channel for
the Radio Band setting, then this setting will be available
for your primary Wireless-N channel. Select any channel
from the drop-down menu.
Standard Channel Select the channel for Wireless-N,
Wireless-G, and Wireless-B networking. If you selected
Wide – 40MHz Channel for the Radio Band setting, then
the Standard Channel will be a secondary channel for
Wireless-N. If you are not sure which channel to select,
keep the default, .Auto
SSID Broadcast When wireless clients survey the local
area for wireless networks to associate with, they will
detect the SSID broadcast by the Router. To broadcast
the Router’s SSID, keep the default setting, . If you Enable
do not want to broadcast the Router’s SSID, then select
Disable.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > Wireless Security
The Wireless Security settings configure the security of
your wireless network. There are six wireless security
mode options supported by the Router: WPA Personal,
WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS,
and WEP. (WPA stands for Wi-Fi Protected Access, which
is a security standard stronger than WEP encryption. WEP
stands for Wired Equivalent Privacy, while RADIUS stands
for Remote Authentication Dial-In User Service.) These
six are briefly discussed here. For detailed instructions
on configuring wireless security for the Router, refer to
“Chapter 2: Wireless Security.”
Wireless Security
Security Mode
Select the mode you want to use: PSK-Personal PSK2-,
Personal PSK-Enterprise PSK2-Enterprise RADIUS, , , ,
or . PSK2 is a more advanced, more secure version of WEP
PSK.
Follow the instructions for the security method you want
to use.
PSK-Personal
Security Mode > PSK-Personal
Encryption. Select the algorithm you want to use, TKIP
or . (AES is a stronger encryption method than TKIP.)AES
Pre-shared Key. Enter the key shared by the Router and
your other network devices. It must have 8-63 characters.
Key Renewal. Enter the Key Renewal period, which tells
the Router how often it should change encryption keys.
When you have finished making changes to this screen,
click the button to save the changes, or Save Settings
click the button to undo your changes. Cancel Changes
For more information, click .Help
PSK2-Personal
Security Mode > PSK2-Personal
Encryption. Select the algorithm you want to use, TKIP
or . (AES is a stronger encryption method than TKIP.)AES
Pre-shared Key. Enter the key shared by the Router and
your other network devices. It must have 8-63 characters.
Key Renewal. Enter the Key Renewal period, which tells
the Router how often it should change encryption keys.
When you have finished making changes to this screen,
click the button to save the changes, or Save Settings
click the button to undo your changes. Cancel Changes
For more information, click .Help
Chapter 3 Advanced Configuration
12
Wireless-N Gigabit Router with Storage Link
Key 1-4 If you want to manually enter the WEP keys, then
enter them in the Key 1-4 fields.Tx Key Select a key from
the drop-down menu.
WEP
Security Mode > WEP
WEP is a basic encryption method offering two levels of
encryption; 128-bit is stronger than 40/64-bit encryption.
Encryption. Select the appropriate level of encryption,
40/64-bit (10 hex digits 128-bit (26 hex digits)) or .
Passphrase. To automatically generate keys, enter your
passphrase. Then click the button.Generate
Key 1-4. If you want to manually enter the WEP keys, then
enter them in the Key 1-4 fields.
TX Key. To indicate which WEP key to use, select a
transmit key number.
When you have finished making changes to this screen,
click the button to save the changes, or Save Settings
click the button to undo your changes. Cancel Changes
For more information, click .Help
NOTE: If you have WEP enabled, and have trouble
using Windows XP or Vista Zero Configuration,
refer to Appendix A: Troubleshooting.
Wireless > Wireless MAC Filter
Wireless access can be filtered by using the MAC addresses of
the wireless devices transmitting within your network’s radius.
Wireless > Wireless MAC Filter
Wireless MAC Filter
Access Restriction
Wireless MAC Filter
To filter wireless users by MAC Address,
either permitting or blocking access, click . If you Enabled
do not wish to filter users by MAC Address, keep the default
setting, Disabled
.
Prevent Select this to block wireless access by MAC
Address. This button is selected by default.
Permit Select this to allow wireless access by MAC
Address. This button is not selected by default.
MAC Address Filter List
Click the Wireless Client List button to display the
Wireless Client List. It shows computers and other devices
on the wireless network. The list can be sorted by Client
Name, Interface, IP address, MAC Address, and Status.
Click the Save to MAC Address Filter List checkbox for
any device you want to add to the MAC Address Filter
List. Then click the button. To retrieve the most up-Add
to-date information, click the button. To exit this Refresh
screen and return to the Wireless MAC Filter screen, click
the button.Close
Chapter 3 Advanced Configuration
13
Wireless-N Gigabit Router with Storage Link
Then click the Enable MAC Filter checkbox for any device
you want to add to the MAC Address Filter List. To update
the information on this list, click the Refresh button.
When you have finished making changes to the Wireless
Client MAC List screen, click the button Update Filter List
to save the changes. Click the button to return to Close
the Wireless MAC Filter screen.
When you have finished making changes to the MAC
Address Filter List screen, click the Save Settings button to
save the changes, or click the button to Cancel Changes
undo your changes.
MAC 01-50. Enter the MAC addresses of the devices
whose wireless access you want to block or allow.
Wireless Client List
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. For more information,
click Help.
Wireless > Advanced Wireless Settings
This screen is used Wireless > Advanced Wireless Settings
to set up the Router’s advanced wireless functions. These
settings should only be adjusted by an expert administrator
as incorrect settings can reduce wireless performance.
Wireless > Advanced Wireless Settings
Advanced Wireless
AP Isolation This isolates all wireless clients and wireless
devices on your network from each other. Wireless devices
will be able to communicate with the Router but not with
each other. To use this function, select Enable. AP Isolation
is on by default. Disable
Frame Burst Enabling this option should provide your
network with greater performance, depending on the
manufacturer of your wireless products. To turn on the
Frame Burst option, select . The default is .Enable Disable
Authentication Type The default is set to , which Auto
allows either Open System or Shared Key authentication
to be used. With Open System authentication, the sender
and the recipient do NOT use a WEP key for authentication.
With Shared Key authentication, the sender and recipient
use a WEP key for authentication.
Basic Rate The Basic Rate setting is not actually one rate
of transmission but a series of rates at which the Router
can transmit. The Router will advertise its Basic Rate to
the other wireless devices in your network, so they know
which rates will be used. The Router will also advertise that
it will automatically select the best rate for transmission.
The default setting is , when the Router can Default
transmit at all standard wireless rates. The Basic Rate is
not the actual rate of data transmission. If you want to
specify the Router’s rate of data transmission, configure
the Transmission Rate setting.
Transmission Rate The rate of data transmission should
be set depending on the speed of your wireless network.
You can select from a range of transmission speeds, or you
can select to have the Router automatically use the Auto
fastest possible data rate and enable the Auto-Fallback
feature. Auto-Fallback will negotiate the best possible
connection speed between the Router and a wireless
client. The default value is .Auto
CTS Protection Mode CTS (Clear-To-Send) Protection
Mode’s default setting is . The Router will Auto
automatically use CTS Protection Mode when your
Wireless-N and Wireless-G products are experiencing
severe problems and are not able to transmit to the
Router in an environment with heavy 802.11b traffic. This
function boosts the Router’s ability to catch all Wireless-
N and Wireless-G transmissions but will severely decrease
performance.
Beacon Interval The default value is . Enter a value 100
between 20 and 1000 milliseconds. The Beacon Interval
value indicates the frequency interval of the beacon. A
beacon is a packet broadcast by the Router to synchronize
the wireless network.
Chapter 3 Advanced Configuration
14
Wireless-N Gigabit Router with Storage Link
DTIM Interval This value, between 1 and 255, indicates
the interval of the Delivery Traffic Indication Message
(DTIM). A DTIM field is a countdown field informing
clients of the next window for listening to broadcast
and multicast messages. When the Router has buffered
broadcast or multicast messages for associated clients, it
sends the next DTIM with a DTIM Interval value. Its clients
hear the beacons and awaken to receive the broadcast
and multicast messages. The default value is .1
Fragmentation Threshold This value specifies the
maximum size for a packet before data is fragmented
into multiple packets. If you experience a high packet
error rate, you may slightly increase the Fragmentation
Threshold. Setting the Fragmentation Threshold too low
may result in poor network performance. Only minor
reduction of the default value is recommended. In most
cases, it should remain at its default value of .2346
RTS Threshold Should you encounter inconsistent data
flow, only minor reduction of the default value, 2346, is
recommended. If a network packet is smaller than the
preset RTS threshold size, the RTS/CTS mechanism will
not be enabled. The Router sends Request to Send (RTS)
frames to a particular receiving station and negotiates
the sending of a data frame. After receiving an RTS, the
wireless station responds with a Clear to Send (CTS) frame
to acknowledge the right to begin transmission. In most
cases, keep its default value of . 2346
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. For more information,
click .Help
Security > Firewall
The Security > Firewall screen is used to configure a firewall
that can filter out various types of unwanted traffic on the
Router’s local network.
Security > Firewall
Firewall
SPI Firewall Protection A firewall enhances network
security and uses Stateful Packet Inspection (SPI) for more
detailed review of data packets entering your network.
Select to use a firewall, or to disable it.Enabled Disabled
Internet Filters
Filter Anonymous Internet Requests This feature
makes it more difficult for outside users to work their
way into your network. This feature is selected by default.
Deselect the feature to allow anonymous Internet
requests
.
Filter Multicast Multicasting allows for multiple
transmissions to specific recipients at the same time. If
multicasting is permitted, then the Router will allow IP
multicast packets to be forwarded to the appropriate
computers. This feature is selected by default. Select
Enabled Disabled to filter multicasting, or to disable this
feature.
Filter Internet NAT Redirection This feature uses
port forwarding to block access to local servers from
local networked computers. Select Filter Internet NAT
Redirection to filter Internet NAT redirection. This feature
is not selected by default.
Filter IDENT (Port 113) This feature keeps port 113 from
being scanned by devices outside of your local network.
This feature is selected by default. Deselect this feature to
disable it.
Web Filters
Proxy Use of WAN proxy servers may compromise the
Gateway’s security. Denying Filter Proxy will disable access
to any WAN proxy servers. Select to enable proxy Enable
filtering.
Java Java is a programming language for websites. If you
deny Java, you run the risk of not having access to Internet
sites created using this programming language. Select
Enable to enable Java filtering.
ActiveX ActiveX is a programming language for websites.
If you deny ActiveX, you run the risk of not having access to
Internet sites created using this programming language.
Select to enable ActiveX filtering. Enable
Cookies A cookie is data stored on your computer and
used by Internet sites when you interact with them. Select
Enable to enable cookie filtering.
When you have finished making changes to this screen,
click the button to save the changes, or Save Settings
click the button to undo your changes. Cancel Changes
For more information, click .Help
Chapter 3 Advanced Configuration
18
Wireless-N Gigabit Router with Storage Link
Delete Click the button to delete a specific Delete
partition from the Router’s database.
After you have made your changes, click the Save Settings
button to apply your changes, or click the Cancel Changes
button to cancel your changes.
Storage > FTP Server
An external USB hard drive or USB disk must be connected
to the USB Port of the Router to use the storage feature.
The FTP Server tab creates an FTP Server that can be
accessed from the Internet or your local network.
Storage> FTP Server
Setup
Server Name The name of the router’s FTP server
is displayed here. It can be changed at Storage >
Administration.
FTP Server Select to set this Router as an FTP Enable
Server. Otherwise, select to turn the service off. Disable
An external USB hard drive or USB disk must be connected
to the USB Port to use this service.
Internet Access Select to allow access of the FTP Enable
Server from the Internet. Otherwise, select Disable to only
allow local network access.
FTP Port Enter the FTP Port number to use. The default
port is 21.
Share
Select the partition or folder to share in the FTP Server.
All Partitions Selects all partitions on the USB disk.
Specify Folder If you want to share a specific folder, click
Select Partition and locate the folder.
Access
Click to grant specific rights to groups. FTP Share Access
You can grant Read Only or Read/Write permissions.
FTP Access Select the group from the Other Group list
and click either the or button to Read Only Read/Write
move the group to the Group With Access column.
After you have made your changes, click the Save Settings
button to apply your changes, or click the Cancel Changes
button to cancel your changes. Click to exit this Close
window.
Access Restrictions > Internet Access
The Access Restrictions > Internet Access screen allows you
to deny or allow specific kinds of Internet usage and traffic,
such as Internet access, designated services, and websites
during specific days and times.
Access Restrictions > Internet Access
Internet Access
Internet Access Policy Internet Access can be managed
by a policy. Use the settings on this screen to establish an
access policy (after is clicked). Selecting a Save Settings
policy from the drop-down menu will display that policy’s
settings. To delete a policy, select that policy’s number
and click . To view all the policies, click .Delete Summary
Deny or Allow If you select Deny, the PC on the Edit
List will be denied Internet Access by the dates and times
selected. PCs not on the list will still have Internet access. If
you select Allow, the PCs on the Edit List will have Internet
access by the dates and times selected. The PCs not on the
Edit List will not have Internet access. If there is a conflict
with a policy, the lower numbered policy will have priority
over a higher numbered policy.
Chapter 3 Advanced Configuration
19
Wireless-N Gigabit Router with Storage Link
To create an Internet Access Policy:
Select a number from the 1. Internet Access Policy drop-
down menu.
Enter a Policy Name in the field. 2.
To enable this policy, select 3. .Enable
Click the 4. button to select which PCs will be Edit List
affected by the policy. The List of PCs screen appears. You
can select a PC by MAC Address or IP Address. You can
also enter a range of IP Addresses if you want this policy
to affect a group of PCs. After making your changes,
click to apply your changes or Save Settings Cancel
Changes to cancel your changes. Then click .Close
List of PCs
Select the appropriate option, 5. or , Deny Allow
depending on whether you want to block or allow
Internet access for the PCs you listed on the List of PCs
screen.
Decide which days and what times you want this policy 6.
to be enforced. Select the individual days during which
the policy will be in effect, or select Everyday. Then
enter a range of hours and minutes during which the
policy will be in effect, or select .24 Hours
Enter a URL address or Keyword for Website Blocking 7.
or select any Blocked Applications you wish to use.
Using these features can slow down your Internet
speed.
Click 8. to save the policy’s settings, or Save Settings
click to cancel the policy’s settings.Cancel Changes
Blocked Applications
You can filter access to various services accessed over the
Internet, such as FTP or telnet, by selecting applications
from the Applications List.
To add an application, enter the application’s name in the
Application Name Port Range field. Enter its range in the
fields. Select its protocol from the drop-down Protocol
menu. Then click .Add
To modify an application, select it from the Application
List. Change the application name, port range, or protocol
setting. Then click .Modify
To delete an application, select it from the Application List.
Then click .Delete
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Applications and Gaming > Single Port
Forwarding
The Single Port Forwarding screen allows you to customize
port services for common applications.
When users send these types of requests to your network via
the Internet, the Gateway will forward those requests to the
appropriate servers (computers). Before using forwarding,
you should assign static IP addresses to the designated
servers.
Applications and Gaming > Single Port Forwarding
Single Port Forwarding
To forward a port, enter the information on each line for
the criteria required.
Application Select pre-configure or enter the name you
wish to give the application. Each name can be up to 12
characters.
External and Internal Port Enter the external and
internal port numbers.
Protocol Select the protocol TCP or UDP, or select Both , .
.
IP Address For each application, enter the IP address of
the computer that should receive the requests.
Enabled For each application, select to enable Enabled
port forwarding.
Chapter 3 Advanced Configuration
20
Wireless-N Gigabit Router with Storage Link
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. For more information,
click .Help
Applications and Gaming > Port Range
Forwarding
The Applications & Gaming > Port Range Forwarding screen
allows you to set up public services on your network, such as
web servers, ftp servers, e-mail servers, or other specialized
Internet applications. (Specialized Internet applications are
any applications that use Internet access to perform functions
such as videoconferencing or online gaming. Some Internet
applications may not require any forwarding.)
Applications and Gaming > Port Range Forwarding
Port Range Forwarding
To forward a port, enter the information on each line for
the criteria required.
Application In this field, enter the name you wish to give
the application. Each name can be up to 12 characters.
Start/End This is the port range. Enter the number that
starts the port range in the Start column and the number
that ends the range in the End column.
Protocol Select the protocol used for this application,
either TCP UDP Both or , or .
IP Address For each application, enter the IP Address of
the PC running the specific application.
Enable Select to enable port forwarding for the Enable
relevant application.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. For more information,
click .Help
Applications & Gaming > Port Range
Triggering
The Applications & Gaming > Port Range Triggering screen
allows the Router to watch outgoing data for specific port
numbers. The IP address of the computer that sends the
matching data is remembered by the Router, so that when
the requested data returns through the Router, the data is
pulled back to the proper computer by way of IP address
and port mapping rules.
Applications and Gaming > Port Triggering
Port Range Triggering
Application Name Enter the application name of the
trigger.
Triggered Range For each application, list the triggered
port number range. Check with the Internet application
documentation for the port number(s) needed.
Start Port •Enter the starting port number of the
Triggered Range.
End Port •Enter the ending port number of the
Triggered Range.
Forwarded Range For each application, list the forwarded
port number range. Check with the Internet application
documentation for the port number(s) needed.
Start Port •Enter the starting port number of the
Forwarded Range.
End Port •Enter the ending port number of the
Forwarded Range.
Enable Select to enable port triggering for the Enable
applicable application.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. For more information,
click .Help
Chapter 3 Advanced Configuration
21
Wireless-N Gigabit Router with Storage Link
Applications and Gaming > DMZ
The DMZ feature allows one network computer to be
exposed to the Internet for use of a special-purpose
service such as Internet gaming or videoconferencing.
DMZ hosting forwards all the ports at the same time to
one PC. The Port Range Forward feature is more secure
because it only opens the ports you want to have opened,
while DMZ hosting opens all the ports of one computer,
exposing the computer to the Internet.
Applications and Gaming > DMZ
DMZ
To use this feature, select Enabled. To disable DMZ hosting,
select .Disabled
Source IP Address If you want any IP address to be the
source, select Any IP Address. If you want to specify an IP
address or range of IP addresses as the designated source,
click the second radio button, and enter the IP address(es)
in the fields provided.
Destination If you want to specify the DMZ host by IP
address, select IP Address and complete the IP address
in the field provided. If you want to specify the DMZ host
by MAC address, select and enter the MAC MAC Address
address in the field provided. To retrieve this information,
click the DHCP Client Table button.
The DHCP Client Table lists computers and other devices
that have been assigned IP addresses by the Router. The list
can be sorted by Client Name, Interface, IP Address, MAC
Address, and Expired Time (how much time is left for the
current IP address). To select a DHCP client, click the Select
button. To retrieve the most up-to-date information, click
the button. To exit this screen and return to the Refresh
DMZ screen, click the button.Close
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. For more information,
click .Help
Applications and Gaming > QoS
Quality of Service (QoS) ensures better service to
high-priority types of network traffic, which may
involve demanding, real-time applications, such as
videoconferencing.
Applications and Gaming > QoS
QoS (Quality of Service)
Wireless
Wireless WMM (Wi-Fi Multimedia) WMM is a wireless
Quality of Service feature that improves quality for audio,
video, and voice applications by prioritizing wireless
traffic. To use this feature, your wireless client devices in
your network must support Wireless WMM. If you would
like to disable this feature, select . Otherwise, Disabled
keep the default, .Enabled
No Acknowledgement If you want to disable the Router’s
Acknowledgement feature, so the Router will not re-send
data if an error occurs, then keep the default, Enabled.
Otherwise, select .Disabled
Internet Access Priority
In this section, you can set the bandwidth priority for a
variety of applications and devices. There are four levels
priority: High, Medium, Normal, or Low. When you set
priority, do not set all applications to High, because this will
defeat the purpose of allocating the available bandwidth.
If you want to select below normal bandwidth, select Low.
Depending on the application, a few attempts may be
needed to set the appropriate bandwidth priority.
Enabled/Disabled. To use the QoS policies you set, select
Enabled Disabled. Otherwise, select .
Category
There are five categories available. Select one of the
following: , , , Applications Online Games MAC Address
Ethernet Port, or Voice Device. Proceed to the instructions
for your selection.
Chapter 3 Advanced Configuration
22
Wireless-N Gigabit Router with Storage Link
Applications
Applications Select the appropriate application. If you
select , follow the Add a New Add a New Application
Application instructions.
Priority Select the appropriate priority: , , High Medium
Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Add a New Application
Enter a Name Enter any name to indicate the name of
the entry.
Port Range Enter the port range that the application will
be using. For example, if you want to allocate bandwidth
for FTP, you can enter 21-21. If you need services for an
application that uses from 1000 to 1250, you enter 1000-
1250 as your settings. You can have up to three ranges
to define for this bandwidth allocation. Port numbers
can range from 1 to 65535. Check your application’s
documentation for details on the service ports used.
Select the protocol TCP UDP, Bothor or select .
Priority Select the appropriate priority: , , High Medium
Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Online Games
Games Select the appropriate game. If you select Add a
New Game, follow the Add a New Game instructions.
Priority Select the appropriate priority: , , High Medium
Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Enter a Name Enter any name to indicate the name of
the entry.
Port Range Enter the port range that the application will
be using. For example, if you want to allocate bandwidth
for FTP, you can enter 21-21. If you need services for an
application that uses from 1000 to 1250, you enter 1000-
1250 as your settings. You can have up to three ranges
to define for this bandwidth allocation. Port numbers
can range from 1 to 65535. Check your application’s
documentation for details on the service ports used.
Select the protocol TCP UDP, Bothor or select .
Priority Select the appropriate priority: , , High Medium
Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
MAC Address
Enter a Name Enter a name for your device.
MAC Address Enter the MAC address of your device.
Priority Select the appropriate priority: , , High Medium
Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Ethernet Port
Ethernet Select the Ethernet port that you want to use.
Priority Select the appropriate priority: , , High Medium
Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Voice Device
Enter a Name Enter a name for your voice device.
MAC Address. Enter the MAC address of your voice
device.
Priority Select the appropriate priority: , , High Medium
Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Summary
This lists the QoS entries you have created for your
applications and devices.
Priority This displays the bandwidth priority of , High
Medium Normal, , or Low.
Name This displays the application, device, or port
name.
Information This displays the port range or MAC address
entered for your entry. If a pre-configured application or
game was selected, there will be no valid entry shown in
this section.
Remove Click this button to remove an entry.
Edit Click this button to make changes.
When you finish making changes to this screen, click Save
Settings Cancel Changes to save the changes, or click to
undo your changes. For more information, click .Help
Chapter 3 Advanced Configuration
23
Wireless-N Gigabit Router with Storage Link
Administration > Management
The screen allows the Administration > Management
network’s administrator to manage specific Router
functions for access and security.
Administration > Management
Router Password
Router Access
To ensure the Router’s security, you will be asked for your
password when you access the Router’s Web-based Utility.
The default password is .admin
Router Password Enter a new Password for the Router.
Re-enter to confirm Enter the Password again to confirm.
Web Access
Web Utility Access HTTP (HyperText Transport Protocol)
is the communications protocol used to connect to servers
on the World Wide Web. HTTPS uses SSL (Secured Socket
Layer) to encrypt data transmitted for higher security.
Select or The default selection is .HTTP HTTPS. HTTP
Web Utility Access via Wireless If you are using the
Router in a public domain where you are giving wireless
access to your guests, you can disable wireless access to
the Router’s web-based utility. You will only be able to
access the web-based utility via a wired connection if you
disable the setting. Keep the default, , to enable Enable
wireless access to the Router’s web-based utility, or select
Disable to disable wireless access to the utility.
Remote Access
Remote Management To access the Router remotely
from the Internet, select . Enable
Web Utility Access Select from HTTP or HTTPS
communications protocols for remote access from the
Internet.
Remote Upgrade Select to be able to upgrade Enabled
the firmware remotely from the Internet.
Allowed Remote IP Address Select or Any IP Address
manually enter an IP address to allow remote access to the
Web-based Utility from the Internet.
Remote Management Port Enter the port number that
will be open to outside access to access the Router’s Web-
based Utility. You will need to enter the Router’s password
when accessing the Router this way, as usual.
UPnP
UPnP Keep the default, to enable the UPnP Enable
feature; otherwise, select .Disable
Allow Users to Configure To use Allow Users to
Configure, select .Enabled
Allow Users to Disable Internet Access To use Allow
Users to Disable Internet Access, click .Disabled
Backup Configurations To back up the Router’s
configuration file, click this button. Then, follow the on-
screen instructions.
Restore Configurations To restore the Router’s
configuration file, click the Browse button to locate the
file, and follow the on-screen instructions. After you select
the file, click this button.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. For more information,
click .Help
Administration > Log
The Router can keep logs of all traffic for your Internet
connection.
Administration > Log
Log
Log To disable the Log function, keep the default setting,
Disabled. To monitor traffic between the network and the
Internet, select .Enabled
When you wish to view the logs, click View Log.
Produkt Specifikationer
| Mærke: | Linksys |
| Kategori: | Routere |
| Model: | WRT350N |
Har du brug for hjælp?
Hvis du har brug for hjælp til Linksys WRT350N stil et spørgsmål nedenfor, og andre brugere vil svare dig
Routere Linksys Manualer
8 Oktober 2024
8 Juli 2024
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
5 Oktober 2022
Routere Manualer
- Routere TP-Link
- Routere D-Link
- Routere Asus
- Routere Clas Ohlson
- Routere Trust
- Routere König
- Routere Technicolor
- Routere Tilgin
- Routere Gembird
- Routere Exibel
- Routere Western Digital
- Routere LevelOne
- Routere EnGenius
- Routere Phicomm
- Routere Sitecom
Nyeste Routere Manualer
12 Januar 2025
12 Januar 2025
15 Oktober 2024
13 Juli 2024
13 Juli 2024
13 Juli 2024
13 Juli 2024
13 Juli 2024
12 Juli 2024
12 Juli 2024