Livex Lighting Villa Verona 8565-63 Manual

Livex Lighting Lys Villa Verona 8565-63

Læs gratis den danske manual til Livex Lighting Villa Verona 8565-63 (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Livex Lighting Villa Verona 8565-63, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

ASSEMBLING & INSTALLATION INSTRUCTIONS

The drawing shown may not exactly match the product enclosed.

However, the installation instructions do apply to this product.

8565 8577

 WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

 ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.

ASSEMBLING THE FIXTURE (Fig.2)

1. Attach the loop (J) to the top center pipe nipple of the fixture body(K) by turning it clockwise

until tight.

2. Attach the end hook of arm(L) to the big ring(N) and aligning the holes on it, lock them with

the knob screw(M), then fasten the other epnd of arm(L) to the fixture body(K) aligning the

holes on it, lock them with the knob screw(M).

3. Install the light bulbs in accordance with the fixture specifications. NOTE: DO NOT

EXCEED THE SPECIFIED WATTAGE!

4. Thread pipe(O) into center coupling of the fixture body(K) and tighten it with the hex nut.

Raise the glass(P) onto the big ring(N) and protruding the pipe(O) from the center hole of

the glass. Attach the plastic shim (Q) and iron shim(R) onto the glass and tighten it firmly

with the hex nut(S). Attach the cover (T) to the glass and tighten it firmly with the finial(U).

HANGING THE FIXTURE (Fig.1)

1. Shut off the power at the circuit breaker and remove old fixture from ceiling, including the old

single bar. Carefully unpack new fixture and lay all the parts on a clear surface.

2. Thread nipple (C) into loop (F) until snug. Thread other end of nipple (C) with loop attached

into single bar (D) until snug.

3. Place lock washer (B) over end of nipple protruding through single bar and thread hex nut

(A) onto nipple until tight.

4. Take this single bar assembly and mount to ceiling junction box with junction box screws

(E). Tighten screws securely with screwdriver.

5. Using proper chain pliers to open one end link of the chain provided and connect to the

fixture loop. Close the link.

6. By measuring, determine correct number of links needed for proper hanging height. Using

proper chain pliers disconnect and discard remaining chain.

7. Lace the fixture wires through the chain.

8. Slip loop collar (H) over the chain, then do the same with the canopy (G).

9. Open the other end link of the chain and hang the fixture on the loop at the ceiling . Close

the link. Feed the fixture wires through the loop (F) and nipple (C) and pull until taut.

**If you not need assembly the fixture loop , please pause and refer to Fig 2.1.**

1. Take out the loop(J) of the fixture body(K). Attach the fixture body to the ceiling, lock it

securely with the ball nut.

CONNECTING THE WIRES (Fig.3)

1. Take the black wire from the ceiling junction box and the smooth wire leg from the fixture

and twist bare ends together. Twist wire connector onto end of wire until snug.

2. Repeat same process with white junction box wire and ribbed wire leg of fixture wire. NOTE:

Twist wires together in the same direction you twist the wire connector onto wires.

3. If your junction box has a grounding wire (green or bare copper), attach this wire and the

bare copper wire from the fixture together as step 1.If junction box has no ground wire,

attach the bare copper fixture wire to the green ground screw on the crossbar.

4. Tuck these wire connections neatly into the ceiling outlet box and then raise the canopy (G)

all the way to the ceiling. Raise the loop (H) and thread onto ceiling loop protruding through

canopy.

Your installation is now complete. Return power to the junction box and test the fixture.

Fig.2.1

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black(Hot)

FIXTURE

WIRES

White or

Ribbed

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

White

(Neutral)

HOUSE

WIRES

Green or Bare

Copper(Ground)

Thank you for purchasing a LIVEX product.

Need assistance with parts or assembly? Please call customer service at: 800-761-8056

Or visit us on-line at: WWW.LIVEXLIGHTING.COM

FIG.3

FIG.1

Produkt Specifikationer

Mærke:	Livex Lighting
Kategori:	Lys
Model:	Villa Verona 8565-63

Har du brug for hjælp?

Hvis du har brug for hjælp til Livex Lighting Villa Verona 8565-63 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Livex Lighting Manualer

Livex Lighting Jefferson 5062-07 Manual

4 November 2024

Livex Lighting Arabesque 41109-91 Manual

4 November 2024

Livex Lighting Jefferson 5061-04 Manual

4 November 2024

Livex Lighting Arabesque 41108-91 Manual

4 November 2024

Livex Lighting Jefferson 5081-01 Manual

4 November 2024

Livex Lighting 7341-07 Manual

4 November 2024

Livex Lighting Milford 4037-07 Manual

4 November 2024

Livex Lighting Legacy 5024-01 Manual

4 November 2024

Livex Lighting 6524-91 Manual

3 November 2024

Livex Lighting Arabesque 41107-91 Manual

3 November 2024

Lys Manualer

Nyeste Lys Manualer

GVM -SD600S-II Manual

13 November 2025

Sagitter J Spot 250 Manual

13 November 2025

ARRI SkyPanel S60 Pro Manual

13 November 2025

Elation ELED DW PAR56 Manual

13 November 2025

Kino Flo Image L80 LED DMX Manual

13 November 2025

ARRI SkyPanel S30-RP Manual

13 November 2025

Sagitter Club Wash Manual

13 November 2025

Sagitter Club Beam 100 Manual

13 November 2025

SDJ SG BLINDER4L Manual

13 November 2025

XCell Worklight Twin Manual

13 November 2025