Lowrance EP-10 Fuel Flow Manual

Lowrance Ikke kategoriseret EP-10 Fuel Flow

Læs gratis den danske manual til Lowrance EP-10 Fuel Flow (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Lowrance EP-10 Fuel Flow, eller vil du spørge andre brugere om produktet?

Side 1/8
1
`Pub. 988-0154-431
EP-10 Fuel Flow
Electronic Sensor
Installation Instructions
This instruction manual explains how to install your EP-10 fuel flow
sensor and connect it to a NMEA 2000 network using LowranceNET
network components. You must refer to your digital gauge, sonar or
GPS unit's manual for sensor operation instructions.
Caution:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. You should decide where to
install all components before drilling any holes in your vessel.
Some sonar or GPS units may require a software upgrade to display
NMEA 2000 data correctly and a manual addendum describing how to
operate the sensor. You can download these free and get additional
information on the NMEA 2000 compatible LowranceNET system at
our web site, .www.lowrance.com
WARNING:
Do not use this sensor with diesel engine fuel systems.
The EP-10 is designed only for gasoline engines. Please
see fuel filter warning on page 4 for additional
information.
The EP-10 Fuel Flow sensor.
Blue female NMEA
2000 connector
Sensor
module
2
All Lowrance NMEA 2000 capable devices are NMEA 2000 certified or
certification is pending. See our web site for the latest product status
information.
The EP-10 consists of a blue female locking cable connector and the
sensor module. The sensor module contains a turbine to measure fuel
flow and electronics which convert flow data to the NMEA 2000 data
format. The cable length from the connector to the smart module is 10
feet. The EP-10 sensor is designed to work with engines only.gasoline
This sensor has been optimized to measure flow rates between 0.6 to 45
gallons (U.S.) per hour, but it will operate at flow rates outside that
range. The sensor will add 0.5 PSI of back pressure on the fuel system
with a flow rate of 20 gallons per hour. At the rate of 40 gallons per
hour the back pressure will be 1 PSI.
The EP-10, like other Lowrance Electronic Probe (EP) sensors, is
designed only for use with a NMEA 2000 Network. It bemust
connected to a NMEA 2000 network or it function.will not
Tools and Supplies
Your EP-10 sensor comes with a T connector. The T connector is needed
to attach the sensor to a LowranceNET NMEA 2000 network. If you are
connecting to an existing LowranceNET network, those are all the
electronic components you need. If this is the first sensor you are
connecting, you also will need a one-time purchase of a LowranceNET
Node Kit.
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2 foot
extension cable, T connector, 120-ohm male terminator and 120-ohm
female terminator.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one refer to the "Setup and Installation of NMEA
2000 Networks, General Information" document (part number 988-


Produkt Specifikationer

Mærke: Lowrance
Kategori: Ikke kategoriseret
Model: EP-10 Fuel Flow

Har du brug for hjælp?

Hvis du har brug for hjælp til Lowrance EP-10 Fuel Flow stil et spørgsmål nedenfor, og andre brugere vil svare dig