LYYT AL1-W2915 Manual

LYYT Controller AL1-W2915

Læs gratis den danske manual til LYYT AL1-W2915 (4 sider) i kategorien Controller. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om LYYT AL1-W2915, eller vil du spørge andre brugere om produktet?

Side 1/4
153.743UK User Ma al nu
RGB/RGBW Sound Active Controller
I ref: 153.743UK tem User Manual
Wireless controller for RGB/RGBW multi-colour LED tape with a 24-key handheld remote. Capable of operating 12V or
24V tape with up to 5A per channel (R/G/B) 4A (R/G/B/W). Options for 8 static colours, 3 auto sequences with speed or
control or 3 sound-activated sequences from an internal microphone or 3.5mm audio input with sensitivity control.
Operating with this controller enables RGB/RGBW tape to give sound-reactive colour to architectural features or signage.
Note: This controller can operate with 12V or 24V LED tape up to 5A maximum output per channel for R/G/B tape 5(1 A
total) and up to 4A maximum output per channel for R/G/B/W tape ( A total). For longer runs of RGB and RGBW p16 ta e
with higher current requirements, RGB/RGBW amplifiers with additional power supplies will be necessary.
If you have bought one of our LED Tape kits, you will have been supplied with a 4-pin lead to connect to connect to
RBG/RGBW tape from the controller rip the wires for R G B W + and connect to the relative screw terminals on . St / / / / V
the controller. you haven t bought one of r LED Tape kits, you will have to purchase this lead separately If ou .
Main Unit Specification:
Working temperature
- - 20 60
Supply voltage
DC5V-24V
Static power consumption
<1W
Connecting mode
common anode
Grayscale
1024 levels (RGB each)
Speed stage
100 graduations
External dimension
L72*W42*20mm
Packing size
L92*W56*H32 mm
Net weight
52g
Gross weight
81g
Output
3/4 channels
Max. Output current
3*5A(RGB)/4*4A(RGBW)
RF frequency
433.92Mhz
Remote distance
Up to 20M
PWM frequency
1.95KHz
Memory function
Yes
Short-circuit protection
Yes
Max. Output power
80W(5V); 192W(12V); 384W(24V)
RF Remote-Control Specification:
Version 1.0
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
Working temperature
Supply voltage
DC3V CR2025 ( )
Standby current
Working current
12mA
Standby power
Working power
36mW
Net weight
RF frequency
433.92MHz
External dimension
RF distance
≤20m
153.743UK User Ma al nu
Main Unit Layout:
RF Remote Control Layout:
Setting up:
Connect the +V, R, G, B (and W if using RGBW tape) output to the LED tape using a connection lead, ensuring that all
terminals are fed to the correct connections on the tape. Connect 12Vdc or 24Vdc power to the DC5521 jack input or DC
power input terminals ensuring that both power supply and controller have enough current capacity to operate the ,
connected tape.
Remove the plastic tab from the handheld RF remote control unit to activate the battery (Button cell CR2025). Power up
the main control unit from the 12Vdc or 24Vdc power supply and if the LEDs are not lit, press the power ‘ON’ key on the
remote control.
Use the ‘SET’ button to set the controller according to the type of LED tape being used. The indicator light will flash
slowly for RGB tape and flash fast for RGBW tape setting.
Select static colours by pressing one of the colour keys on the remote control. Use the two brightness keys to adjust the
brightness of the LED’s. short press on the W key will switch the white LED ght on/off. A long press on the W key will A li
dim the white LED light.


Produkt Specifikationer

Mærke: LYYT
Kategori: Controller
Model: AL1-W2915

Har du brug for hjælp?

Hvis du har brug for hjælp til LYYT AL1-W2915 stil et spørgsmål nedenfor, og andre brugere vil svare dig