Mean Well DRA-40-12 Manual

Mean Well Ikke kategoriseret DRA-40-12

Læs gratis den danske manual til Mean Well DRA-40-12 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 112 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 56.5 anmeldelser. Har du et spørgsmål om Mean Well DRA-40-12, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Installaon Manual

 Type：

：

：：DRA DIN rail power supply Series DRA-40, DRA-

（

（（：

：

：： 60）

）

））

DRA- - INPUT: -240VAC 0.8A 50/60Hz OUTPUT: V 3.34A 40 12 100 12

DRA- - INPUT: -240VAC 0.8A 50/60Hz OUTPUT: V 1.7A 40 24 100 24

DRA- - INPUT: -240VAC 1.3A 50/60Hz OUTPUT: V 5A 60 12 100 12

DRA- - INPUT: -240V 1.3A 50/60Hz OUTPUT: V 2.5A 60 24 100 AC 24

 Introducon

DRA is a DIN rail power supply series featuring adjustable output current. Users are able to set its output current to

a range of 10% - 100% of rated current via 1-10Vdc, PWM signal or resistance. Like other Mean Well s DIN series, ’

they can be mounted on a TS35 Standard DIN rail.

 Installaon

（）1 Always allow good venlaon clearances, 5mm le and right, 40mm above and 20mm below, around the unit

in use to prevent it from overheang. Also a 10-15 cm clearance must be kept when the adjacent device is a

heat source.

（）2 The appropriate mounng orientaon for the unit is vercal, the input terminals the bottom and output on at

the top. Mounng orientaons other than that, such as upside down, horizontal, or table-top mounng, is not

allowed.

（）3 Use copper wire only, and recommended wires are shown as below.

AWG

Rated Current of

Equipment (Amp)

Cross-secon of

Lead(mm2 )

0.8

1.3

2.1

3.3

Note Current each wire carries should be de-rated to 80% of the current suggested ：

above when using 4-6 wires connected to the unit.

Make sure that all strands of each stranded wire enter the terminal connecon and the screw terminals are

securely xed to prevent poor contact. If the power supply possesses mul-output terminals, please make

sure each contact is connected to wires to prevent too much current stress on a single contact.

（）4 Use wires that can withstand temperatures of at least 80°C, such as UL1007.

（）5 Recommended wire strapping length m (0.197 . is 5m ”)

（）6 Recommended screwdriver is 3 , sloed type.mm

（）7 The recommended torque seng for terminals(TB1) is 5 kgf‐cm (4.4 Lb‐in),

terminals(TB2) is 5 5 .8 kgf‐cm ( Lb‐in).

（）8 Each unit requires 0.15mA when dimming funcon is used. Please make sure your controller is capable of

driving the units.

Produkt Specifikationer

Mærke:	Mean Well
Kategori:	Ikke kategoriseret
Model:	DRA-40-12
Bredde:	40 mm
Dybde:	100 mm
Højde:	90 mm
Vægt:	280 g
Antal pr. pakke:	42 stk
Udgangseffekt:	40 W
Udgangsspænding:	12 V
Bæredygtighedscertifikater:	RoHS
Indgangsspænding:	90 - 264 V