Microchip MIC5385 Manual

Microchip Ikke kategoriseret MIC5385

Læs gratis den danske manual til Microchip MIC5385 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Microchip MIC5385, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

MIC5385 Evaluation Board

Ultra-Small Triple 150mA Output LDO

MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.

Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com

General Description

The MIC5385 is an advanced, triple-output, low-noise LDO

for powering general purpose portable devices. The

MIC5385 provides three independently-enabled, high-

performance, 150mA LDOs in an ultra-small 2mm x 2mm

Thin MLF® package while using only four external

components.

Ideal for battery-powered applications, the MIC5385 offers

low dropout voltage of 180mV at 150mA and low ground

current (typically 32µA per LDO). It can also be put into a

zero-off-mode current state, drawing virtually no current

when disabled.

An input capacitor is required when the power supply is

more than four inches from the device. The evaluation

board includes an input capacitor of 10µF to compensate

for long inductive test leads.

Data sheets and support documentation can be found on

Micrel’s web site at: www.micrel.com.

Requirements

The MIC5385 evaluation board requires an input power

supply that is capable of delivering a minimum 600mA at a

voltage range of 2.5V to 5.5V. The output load can be

either active or passive.

Precautions

The MIC5385 evaluation board does not have reverse

polarity protection. Applying a negative voltage to the VIN

terminal may damage the device.

Getting Started

• Connect an External Supply to V IN. Apply the desired

input voltage to the VIN (J1) and ground (J2) terminal of

the evaluation board, paying careful attention to polarity

and supply voltage (2.5V ≤ VIN ≤ 5.5V). An ammeter can

be placed between the input supply and the V IN terminal

of the evaluation board. Ensure that the supply voltage

is monitored at the VIN terminal. The ammeter and/or

power-lead resistance can reduce the voltage supplied

to the input.

• Enable/Disable the MIC5385. To enable the MIC5385

jumper, the enable terminal (J5 for LDO1, J4 for LDO2,

and J3 for LDO3) to V IN

. To disable the output, simply

remove the jumper from the EN terminal. The enable pin

must be either pulled high or low. Leaving the pin

floating will cause the regulator to operate in an

indeterminate state. The evaluation board is supplied

with 100KΩ pull-down resistors for default off state.

• Connect the Load. Connect the load to the VOUT

Terminals (J7 for LDO1, J8 for LDO2 and J6 for LDO3)

and Ground Terminal (J9, J10). The load can be either a

passive (resistor) or active (electronic load). Be sure to

monitor the output voltage at the VOUT (J6, J7 and J8)

terminals.

Ordering Information

April 2010 M9999-041610-A

_________________________________________________________________________________________________________________________

Part Number Description

MIC5385-SGFYMT EV Triple-Output LDO Evaluation Board.

VOUT1 =3.3V, VOUT2 =1.8V, VOUT3 =1.5V

Micrel, Inc. MIC5385 Evaluation Board

April 2010 2 M9999-041610-A

Evaluation Board Schematic

Bill of Materials

Item Part Number Manufacturer Description Qty.

C1 C1608X5R0J106K TDK(1) 10μF, Ceramic, 6.3V, X5R, Size 0603 Capacitor 1

GRM155R1A1055KE19D Murata(2) 1μF, Ceramic, 10V, X5R, Size 0402 Capacitor

0402ZD105KAT2A AVX(3) 1μF, Ceramic, 10V, X5R, Size 0402 Capacitor

C2, C3, C4

LMK105BJ105KV-F Taiyo Yuden(4) 1μF, Ceramic, 10V, X5R, Size 0402 Capacitor

R1, R2, R3 CRCW0402100KFKEA Vishay(5) 100KΩ, 1%, 1/16W, Size 0402 Resistor 3

U1 MIC5385-SGFYMT Micrel, Inc.(6) High-Performance, Triple-Output, 150mA LDO 1

Notes:

1. TDK: www.tdk.com.

2. Murata: www.murata.com.

3. AVX: www.avx.com.

4. Taiyo Yuden: www.t-Yuden.com.

5. Vishay: www.vishay.com.

6. Micrel, Inc.: www.micrel.com.

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	MIC5385

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC5385 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip HS12-100D0/12DS2F Manual

18 Februar 2025

Microchip HSA0-040SDA/A0SA10 Manual

18 Februar 2025

Microchip HSA0-040SIA/A0S1F Manual

18 Februar 2025

Microchip HT12-100S0s/12ST25 Manual

17 Februar 2025

Microchip EMC2103-2 Manual

17 Februar 2025

Microchip EMC1047 Manual

17 Februar 2025

Microchip HCS201 Manual

17 Februar 2025

Microchip LE9653 Manual

17 Februar 2025

Microchip LAN7430 Manual

17 Februar 2025

Microchip HCS500 Manual

17 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

XO D1HPBF Manual

16 Juni 2025

Fantech RS1 Manual

16 Juni 2025

Playtive IAN 425414 Manual

16 Juni 2025

Playtive IAN 321249 Manual

16 Juni 2025

Playtive IAN 115930 Manual

16 Juni 2025

Aiphone GT-102HB Manual

16 Juni 2025

Playtive HG05516 Manual

16 Juni 2025

Playtive IAN 295154 Manual

16 Juni 2025

Playtive IAN 324362 Manual

16 Juni 2025

Playtive IAN 302521 Manual

16 Juni 2025