Milwaukee RMS 2217-20NST Manual

Milwaukee Multimeter RMS 2217-20NST

Læs gratis den danske manual til Milwaukee RMS 2217-20NST (15 sider) i kategorien Multimeter. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Milwaukee RMS 2217-20NST, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/15
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN
COMPRENDRE LE MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL
MANUAL DEL OPERADOR.
TRUE RMS MULTIMETER (DMM)
MULTIMÈTRE D'EFFICACITÉ VÉRITABLE (DMM)
MULTÍMETRO CON RMS VERDADERO (DMM)
Cat. No.
No de cat.
2217-20
23
IMPORTANT SAFETY INSTRUCTIONS
WARNING READ ALL SAFETY WARNINGS AND INSTRUCTIONS. Failure to
follow the warnings and instructions may result in electric shock, fi re and/or serious
injury, as well as instrument damage and/or damage to the equipment being tested. Save these
instructions - This operator’s manual contains important safety and operating instructions
for the MILWAUKEE True RMS Multimeters (DMM). Before using, read this operator’s manual
and all labels on the True RMS Multimeters.
DANGER
Never make measurement on a circuit in which voltage over 600V rms exists. Use only leads
rated 600V CATIII or better.
Do not apply more than the rated voltage, as marked on the DMM, between terminals or be-
tween any terminal and earth ground.
Do not attempt a current measurement when the open voltage is above the fuse protection
rating. Suspected open circuit voltage can be checked with voltage function.
Do not use the DMM to measure voltages in circuits that could be damaged by the DMM’s low
input impedance in Lo-Z Function. Impedance is approximately 4K .Ω
Do not attempt to make measurement in the presence of fl ammable gases. Otherwise, the use
of the instrument may cause sparking, which can lead to an explosion.
Never attempt to use the instrument if its surface or your hand is wet.
Do not exceed the maximum allowable input of any measuring range.
Only test on unenergized circuits unless absolutely necessary.
Check tool functionality on a known circuit fi rst. Never assume tool is working. Assume circuits
are live until they can be proven de-energized.
Never open the Battery cover during a measurement.
Do not ground yourself while measuring. Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrigerators.
This instrument is to be used only in its intended applications or conditions. Otherwise, the instru-
ment's safety functions may not work, resulting in serious personal injury and instrument damage.
To reduce the risk of injury from shock and arc blasts, always wear personal protective
equipment where live conductors are exposed.
WARNING
Never attempt to make measurement if any abnormal conditions, such as broken case and
exposed metal parts are found on the instrument.
Comply with local and national safety requirements when working in hazardous locations.
Keep fi ngers behind the guards and away from test lead tips during measurements.
Do not rotate the Rotary Dial while the test leads are being connected.
Never attempt a voltage measurement with the test lead inserted into the A input terminal.
Verify proper operation on a known source before use or taking action as a result of the in-
dication of the instrument.
Do not install substitute parts, replace fuse or make any modifi cation to the instrument. For
repair or re-calibration, return the tool to a factory Service/Sales Support Branch or authorized
service station.
Do not try to replace the batteries if the surface of the instrument is wet.
Disconnect all the cords and cables from the object under test and power off the instrument
before opening the Battery Cover for Battery replacement.
This tool is designed to be powered by 2-AA batteries properly inserted into the MILWAUKEE
True RMS Multimeters. Do not attempt to use with any other voltage or power supply.
Install battery according to polarity (+ and –) diagrams.
Do not leave batteries within the reach of children.
Do not mix new and used batteries. Do not mix brands (or types within brands) of batteries.
Properly dispose of used batteries.
Do not incinerate or dismantle batteries.
Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact
accidentally occurs, fl ush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.

Produkt Specifikationer

Mærke: Milwaukee
Kategori: Multimeter
Model: RMS 2217-20NST

Har du brug for hjælp?

Hvis du har brug for hjælp til Milwaukee RMS 2217-20NST stil et spørgsmål nedenfor, og andre brugere vil svare dig


Multimeter Milwaukee Manualer

Milwaukee

Milwaukee Digital Angle Gauge Manual

16 September 2025
Milwaukee

Milwaukee 2237-20 Manual

16 August 2024
Milwaukee

Milwaukee RMS 2217-20NST Manual

22 Juli 2024
Milwaukee

Milwaukee 2206-20 Manual

19 Juli 2024
Milwaukee

Milwaukee 2205-20 Manual

8 Juli 2024
Milwaukee

Milwaukee 2236-20 Manual

25 Oktober 2023
Milwaukee

Milwaukee 2235-20 Manual

12 Marts 2023
Milwaukee

Milwaukee 2216-20 Manual

15 November 2022
Milwaukee

Milwaukee 2212-20 Manual

12 November 2022

Multimeter Manualer

Nyeste Multimeter Manualer

Gossen Metrawatt

Gossen Metrawatt SECULIFE HIT AM Manual

26 September 2025
Gossen Metrawatt

Gossen Metrawatt METRAHIT IM E-DRIVE BT Manual

26 September 2025
Draper

Draper 41821 Manual

23 September 2025
Draper

Draper 37317 Manual

23 September 2025
Draper

Draper 41817 Manual

23 September 2025
REV

REV EM8900A Manual

21 September 2025
FERM

FERM MM-1000 Manual

20 September 2025
Testboy

Testboy TB 317 Manual

18 September 2025
Testboy

Testboy TB 318 Manual

18 September 2025
Amiko

Amiko TSC-1100 Manual

14 September 2025