Monacor KP70-400 Manual

Monacor Ikke kategoriseret KP70-400

Læs gratis den danske manual til Monacor KP70-400 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Monacor KP70-400, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
Manufactured by :
CRC Industries Europe BVBA
Touwslagerstraat 1 – 9240 Zele – Belgium
Tel (32) (0) 52/45.60.11 Fax (32) (0) 52/45.00.34
www.crcind.com
TECHNICAL DATA SHEET
1/3
PLASTIK 70
Ref. : 20743
1. GENERAL DESCRIPTION
Quick drying, colorless transparent insulating and protective coating based on acrylic resins.
2. FEATURES
• PLASTIK 70 is a low viscosity, solvent drying acrylic based conformal coating with
excellent insulating properties. The lacquer is colorless transparent and elastic. It has a
durable adhesion in the temperature range from –40°C to +60°C and can be used for a
short period of time up to +100°C maximum. It protects printed circuit boards and
surfaces from humid inorganic-acid or caustic vapors.
• PLASTIK 70 is colorless-transparent and as such is not visual on the printed circuit board
surface.
• Contains “moisture warning”: To avoid involuntary encapsulations of moisture, Plastik 70
will warn you when applied on a humid surface, by showing a frosted, mat appearance.
• For repair works PLASTIK 70 can be soldered through or be totally removed with
acetone, THINNER FOR PLASTIK 70.
3. APPLICATIONS
PLASTIK 70 was specially developed to protect printed circuit boards. It overcomes electrical
leakages and short circuits.
As a low viscosity xing and insulating lacquer, PLASTIK 70 can also be used as extra/after
insulation of coils and transformers and overcomes disturbing noises.
PLASTIK 70 can also be used as a universal protective coating on any surface like metal,
paper, ornaments, paintings, furniture, etc.
4. DIRECTIONS
• For small runs and service applications, the easiest way to apply PLASTIK 70 is from an
aerosol can. Spray from a distance of 20 to 30 cm on the dry and degreased surface. As
pre-cleaning of PCB’s, we do recommend the use of KONTAKT PCC to remove greases,
dirt and ux residues. When nished spraying, clean the aerosol valve by turning the can
upside down and pressing the button until only propellant escapes.
• For serial production runs, PLASTIK 70 in bulk can be applied by brush or by dipping. For
spraying, two parts per volume PLASTIK 70 is diluted with up to one part of THINNER
FOR PLASTIK 70. The precise mixing ratio must be determined by trials with the
equipment concerned.
• For dip coating it is also necessary to x the immersion time and the withdrawal speed.
The faster the removal from the bulk, then thicker the lm will be. Dipping baths have to
be carefully protected to ensure no entrapment of conductive stuck-on residues.
Manufactured by :
CRC Industries Europe BVBA
Touwslagerstraat 1 – 9240 Zele – Belgium
Tel (32) (0) 52/45.60.11 Fax (32) (0) 52/45.00.34
www.crcind.com
TECHNICAL DATA SHEET
2/3
PLASTIK 70
Ref. : 20743
• PLASTIK 70 contains solvents like ethyl acetate and butyl acetate. Printed circuit board
materials and electronic components generally have a good compatibility with these
solvents. In case of plastic surfaces (e.g. housings) a compatibility test is always
recommend. It is necessary in particular, to test its suitability for plastics susceptible to
stress cracking (e.g. polycarbonate).
• PLASTIK 70 contains ammable solvents and hence when working with the product,
make sure there is good ventilation in the workplace. Remove all possible ignition
sources.
• A safety data sheet (MSDS) according to EU directive 91/155/EEC and amendments is
available for all CRC products.
5. TYPICAL PRODUCT DATA (without propellant)
As delivered
Coverage at 20µm, calculated : ±0.7m²/200 ml spray
±9m²/litre
Viscosity bulk : 10-20 mPas
Flashpoint : <0°C
Drying time at 20°C (dry to touch) : ±20 minutes
Properties dry lm
(after 24 hrs drying at ambient temperature, thickness 20-40 µm)
Aspect : colorless-transparent
Surface resistivity at 20°C : >10
13 Ω
Volume resistivity at 20°C : >10
13 .cm Ω
Dielectric strength : >80kV/mm
Adhesion to copper plates, measured at ambient temperature
following 6 hrs at –40°C : Gt 0-1
following 6 hrs at +60°C : Gt 0-1
following ½ hr at +100°C : Gt 0-1

Produkt Specifikationer

Mærke: Monacor
Kategori: Ikke kategoriseret
Model: KP70-400

Har du brug for hjælp?

Hvis du har brug for hjælp til Monacor KP70-400 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Monacor Manualer

Monacor

Monacor MHB-12 Manual

27 Juli 2025
Monacor

Monacor DSP-1 Manual

27 Juli 2025
Monacor

Monacor MCS-180 Manual

27 Juli 2025
Monacor

Monacor WP-1 Manual

5 September 2024
Monacor

Monacor EMA-20 Manual

25 August 2024
Monacor

Monacor KKS75-400 Manual

18 August 2024
Monacor

Monacor EX-40/8 Manual

18 August 2024
Monacor

Monacor ATS-35CB Manual

18 August 2024
Monacor

Monacor CU-48DMX Manual

17 August 2024
Monacor

Monacor PM-2/30V Manual

16 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tefal

Tefal Lighted Mirror MR4015 Manual

20 August 2025
Stiebel Eltron

Stiebel Eltron CWM P Manual

20 August 2025
Globe

Globe XPH Manual

20 August 2025
Accucold

Accucold AWC2PB Manual

20 August 2025
Scheppach

Scheppach CSP5300 SE Manual

20 August 2025
AccuTemp

AccuTemp Evolution N61201D060 Manual

20 August 2025
Scheppach

Scheppach C-BSB74/1BE-X Manual

20 August 2025
Deye

Deye SUN-7.6K-SG02LP2-EU-AM2 Manual

20 August 2025
Scheppach

Scheppach Therbio Manual

20 August 2025
Krups

Krups Pulseo KB17GD Manual

20 August 2025