Monacor PREAMP-1UP Manual

Monacor Controller PREAMP-1UP

Læs gratis den danske manual til Monacor PREAMP-1UP (2 sider) i kategorien Controller. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Monacor PREAMP-1UP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Technical data S.1/2

Preamplifier PREAMP

Technical modifications reserved 07/04

Thank you for buying a WHD product. Please read this manual carefully,especially the ! marked parts.

Content :

PREAMP CD500 uP ... :

Pre-Amplifier with metal front plate. Plastic front plate with printing.Plasic rotary knobs.Accessory subframe

CD500 ,colour : “ alpinweiss “

PREAMP uP ... :

Pre-Amplifier with metal front plate. Plastic front plate with printing.Plasic rotary knobs.

Colour : “ alpinweiss “

The subframes are not available at WHD.

PREAMP BJ uP ... :

Pre-Amplifier with metal front plate. Plastic front plate with printing.Plasic rotary knobs.

Colour : “ alpinweiss “

The subframes are not available at WHD.

Specifications :

Supply voltage : 22-26V

Output voltage : 5V max.

Output impedance : 50 Ω

Input voltage Line : 400 mV

Input voltage Mic : 4mV

Frequency range Line : 20-20 000 Hz (-1dB)

Frequency range Mic : 40-15 000 Hz (-3dB)

Current consumption : 0,025 A

Terminal : 7 -pole terminal , removeable

Control voltage : 0-10VDC

Additional parts : ( JUNG/CD500 frames and UP-cabinets KAISER available at WHD)

Subframe Frame

single Frame

double UP-cabinet

61/63 mm

X X X

The microphone volume control has a combined ON-OFF switch.

Technical data - S. 2/2 - Pre- amplifier PREAMP ...

Technical modifications reserved 07/04

Mounting :Mounting :

Connect terminal according to wiring scheme.

Backside view

Note : The control terminal no. 4 gets a voltage of 12V by an internal resistor. So the preamplifier

has the maximum gain at open terminal.

Terminal no

1 + Signal – out ( unbalanced )

2 0 Signal

3 Reduced gain

4 + Control input 0-12 VDC

5 0 V Control

6 0 Supply voltage

7 + 24V Supply voltage

8 0 V Phantom / Mic

9 + Mic input

10 + 24V Phantom

If the gain is too high for some applications , connect the accessory wire bridge to terminal 3 and 5.

This will reduce the gain to app. 1/3.

Note : Teminal 8 to 10 is only for use with input balance unit.

For the signal and control line we recommend shielded cable.

e.g. LIYCY 0.14mm² 2-cores

The cross section of the power supply cable should be adequate.

e.g. H03VV-F 0,5mm² 2-cores

We recommend regulated 24VDC power supply with short circuit protection.

Produkt Specifikationer

Mærke:	Monacor
Kategori:	Controller
Model:	PREAMP-1UP

Har du brug for hjælp?

Hvis du har brug for hjælp til Monacor PREAMP-1UP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Controller Monacor Manualer

Monacor ATT-325ST Manual

14 August 2024

Monacor ATT-324PEU Manual

14 August 2024

Monacor ATT-312PEU Manual

13 August 2024

Monacor PREAMP-1UP Manual

12 August 2024

Monacor ATT-224/WS Manual

12 August 2024

Monacor VCA-202RN Manual

10 August 2024

Monacor ATT-524PEU Manual

9 August 2024

Monacor ATT-512PEU Manual

9 August 2024

Monacor ATT-19100 Manual

9 August 2024

Monacor ATT-2100/WS Manual

7 August 2024

Controller Manualer

Nyeste Controller Manualer

Sonance VC60R Manual

2 April 2025

Trust Mylox GXT 735G Manual

30 Marts 2025

Trust Mylox GXT 735 Manual

30 Marts 2025

American DJ STAGE SETTER-8 Manual

30 Marts 2025

American DJ DP-DMX20L Manual

30 Marts 2025

Visual Productions TimeCore Manual

30 Marts 2025

PCE Instruments PCE-RE22T Manual

28 Marts 2025

Turtle Beach Recon Manual

27 Marts 2025

PowerA Enhanced Wireless Controller Manual

26 Februar 2025

IPEGA PG-9078 Manual

20 Februar 2025