MTX Audio RTU8P Manual

MTX Audio Ikke kategoriseret RTU8P

Læs gratis den danske manual til MTX Audio RTU8P (24 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 13 anmeldelser. Har du et spørgsmål om MTX Audio RTU8P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/24

mtxaudio.eu facebook.com/MTXEuropetwitter.com/MTXEurope

RTU8P

8“ 20cm Underseat Powered Enclosure

150W RMS - 600W Peak

Owner’s Manual - MTX RTU8P

Thank You !

Thank you for purchasing an MTX Audio High-End powered enclosure. Proper installation matched with MTX speakers and powered

enclosures provide superior sound and performance for endless hours of waking the neighbors, slammin’ your friends or ﬂat out

stomping wanna-be players. Congrats and enjoy the ultimate audio experience with MTX !

Speciﬁcations :

• Underseat sealed powered enclosure

• Subwoofer : 20cm (8“)

• Class-AB mono block ampliﬁer

• Peak Power : 600W

• RMS Power : 150W

• Active X-over : variable 50~150Hz

• EBC remote included

• High and low level inputs

• Auto switch on with high-level inputs

• Input sensitivity : 0,1V~4V

• Phase switch : 0° or 180°

• Bass boost : @45Hz variable 0 to +12dB

• Dimensions : 345x242x78mm

• Weight : 5Kg

Power Terminal (+12V) : This is the main power input for the ampliﬁer and must be connected directly to the positive terminal of the

vehicles battery for proper operation. Use caution when installing (+12V) power cable in the vehicle. Avoid running this cable parallel

with RCA cables, antennas, or other sensitive equipment due to massive currents that can induce noise into the audio system. It is also

very important to have a tight, secure connection for maximum performance. MTX recommends using a minimum of 6mm

2 full copper

power wire with the MTX RTU8P.

Remote Terminal (REM) : The ampliﬁer can be turned on by applying 12 volts to this terminal. Typically this voltage is supplied by a wire

from the source unit marked “remote” or “power antenna”.

Note : If you use the high level inputs, the remote function is automatic. You don’t need to connect this cable.

Ground Terminal (GND) : A proper ground is required for your ampliﬁer to operate at peak performance. A short ground cable the same

diameter as the power cable should be used to attach the ground terminal directly to the chassis of the vehicle. Always remove paint,

dirt or debris to expose bare metal where the ground will be attached.

Protection LED (Protect.) : When the amp is in thermal protection, the LED turns to red.

PowerOn LED (Power On) : The LED illuminates red when the amp is switched on.

RCA Inputs (Input) : These RCA inputs are used with source units that have RCA or Line level outputs. (Source units need a minimum

level of 100mV output for proper operation of the ampliﬁer). MTX recommends only high quality RCA cables to decrease the possibility

of radiated noise entering the system.

Gain Control (Gain) : The gain control matches the input sensitivity of the ampliﬁer to the source unit being used.

The operating range varies from 100mv to 4V. Adjusting the gain:

1. Turn the gain control on the ampliﬁer all the way down (counter clockwise).

2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.

3. Adjust the gain control on the ampliﬁer until audible distortion occurs.

4. Adjust the gain control down until audible distortion disappears.

5. The ampliﬁer is now calibrated to the output of the source unit.

Speaker level inputs (High Level Input) : This input will allow the ampliﬁer to operate from source units with speaker-level outputs.

Output speaker leads from the source unit should be tied directly to the wire harness provided with the ampliﬁer.

Note : If you use the high level inputs, the remote function is automatic.

Control Panel on the Ampliﬁer :

RTU8P

8” 150W RMS Powered Enclosure

Input

Ch.1

Ch.2

Power

Protect.

15A

+12V REM GND

EBC

Remote Phase

X-over

Bass

Boost

Gain

4V-0,1V 0°0db +12dB 50Hz-150Hz

High Level

Input

LeftRight

180°

Produkt Specifikationer

Mærke:	MTX Audio
Kategori:	Ikke kategoriseret
Model:	RTU8P

Har du brug for hjælp?

Hvis du har brug for hjælp til MTX Audio RTU8P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret MTX Audio Manualer

MTX Audio ZNXH2L Manual

28 December 2024

MTX Audio Terminator TN500-1D Manual

25 Juli 2024

MTX Audio Thunder Sports MUDRZRDK Manual

25 Juli 2024

MTX Audio Terminator TNA251 Manual

25 Juli 2024

MTX Audio Magnum MB210SP Manual

25 Juli 2024

MTX Audio RTU8P Manual

25 Juli 2024

MTX Audio iX4 Manual

25 Juli 2024

MTX Audio RTP8x2 Manual

25 Juli 2024

MTX Audio iWa250 Manual

25 Juli 2024

MTX Audio RTF10P Manual

25 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025

Navman MiVue 745 Manual

1 August 2025

Hitachi WR22SE Manual

1 August 2025

Synology M2D20 Manual

1 August 2025

Fluke FibertLert-125 Manual

1 August 2025

Buffalo GC882 Manual

1 August 2025