NAKS SF11-3PH Manual

NAKS Emhætte SF11-3PH

Læs gratis den danske manual til NAKS SF11-3PH (7 sider) i kategorien Emhætte. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om NAKS SF11-3PH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

BELT DRIVE

SUPPLY FANS

OPERATION INSTRUCTIONS AND PARTS MANUAL

MODELS: SF5, SF5-3PH, SF7, SF7-3PH, SF8, SF8-3PH, SF9, SF9-3PH, SF10, SF10-3PH

GENERAL SAFETY

Rotating parts, (pulleys, shafts and belts) on fans should not be exposed. Where these components are not protected by ductwork, cabinets

or covers, appropriate guards should be employed to restrict exposure to rotating parts. Access doors should not be opened with the fan

operating to avoid foreign objects being drawn into the system. On initial start-up, a careful inspection should be carried out to ensure no

foreign material is present which could become airborne in the system.

Read installation and operation instructions carefully before attempting to install, operate or service NAKS SF Series Blowers. Failure to

comply with instructions could result in personal injury and/or property damage. Retain instructions for future reference.

BEFORE YOU BEGIN

Inspect unit for damage, report any shipping damage to carrier. Check all fasteners, re-tighten as required. Rotate the blower wheel by

hand to ensure free rotation. If rubbing occurs, loosen the set screw(s), re-position the wheel to the shaft center, re-tighten set screws.

INSTALLATION

Remove hood and filters from inside the cabinet. Caulk top of curb before setting unit in place. (Curb must be smaller than unit “A”

dimension). Secure unit to curb through holes located around the bottom of the unit. Tighten wheel set screw.

BOTTOM VIEW

SIZE QUANTITY

SF5 / SF5-3PH

SF7 / SF7-3PH

22" 24" 11 7/8" 13 1/4" 4 7/16" 3 1/4" 6 7/8" 16" 18 1/8" 19 7/8" 16" x 25" x 1" 1 21 7/8" x 21 7/8" TBA

SF8 / SF8-3PH

SF9 / SF9-3PH

32" 32" 13 3/4" 15 7/8" 8 1/16" 4 1/4" 14" 25" 24 5/8" 25" 16" x 25" x 1" 2 31 7/8" x 31 7/8" TBA

SF10 / SF10-3PH 32" 32" 16 1/8" 18 7/8" 6 9/16" 3 7/8" 12 7/8" 25" 24 5/8" 25" 16" x 25" x 1" 2 31 7/8" x 31 7/8" TBA

UNIT WEIGHT (LBS)

(without motors & drives)

H L M Z

FILTERS

*INSIDE

CABINET

A B D E F GMODEL

2017 Page 1 of 4

REMOVE CAP FOR

FILTER ACCESS

Ø5/16" HOLES

FOR FASTENING

TO CURB

MOTOR, PULLEYS & BELTS (See Table next page)

1. Mount the blower pulley on the blower shaft and tighten the set screw securely on the key of the shaft.

2. Mount the motor pulley on the motor shaft. Leave some clearance between the pulley and the motor end bell. Tighten the set screws

on the key of the motor shaft.

3. Install the motor on the motor platform using the hardware provided.

4. With the platform in its minimum position, install the V-belt within the pulley grooves. Position the motor on the motor platform to

ensure proper pulley alignment (see ) and secure to the motor platform. (A straight edge across the face of the driven pulleyFigure 1

should be parallel to the belt once proper alignment has been achieved).

Note: Adjustments in the variable speed pulley require pulley re-alignment.

*Curb size to be smaller than inside cabinet to allow for ﬂashing and rooﬁng.

**Includes ﬁlter section

5. Pivot the motor platform to tension the V-belt and lock in place using the 2 bolts on both sides of the blower. (Ideal belt tension

is the lowest tension at which the belt will not slip during start up.) As shown in illustration to right, a proper deflection of 1/64 of

the belt span is desired for belt tension.

6" " " " " 2"7 8 9 10 1

8 11 5 RP24- 2 M 680 9 9 RP 580 79 RP 505 90- 2 M - 2 M -6 RPM 447 11 RP-6 M 401 5 8 RP 533 55 RP- 4 M -4 M

4L 4L4 4L4 4L44 4L4 4L4 --39 1 2 6 7

4L4 4L44 4L4 4L4 4L4 4L --2 6 7 9 51

-- -- -- -- 4L 4L 4L 0 FRAME55 57 6 56S 10 S 10 3PF / F - H

B O RL WE MODEL

3 1 C S RO B O R PU D R & RP R G /4 A T I N L WE LLEY - IAMETE M AN E

BELT LEN THG

B S D OA E N

M T FO OR RAME

S 5 S 5 3PF / F - H

S 7 S 7 3PF / F - H

4 FRAME8

S 8 S 8 3PF / F - H

S 9 S 9 3PF / F - H

M ll yotor Pu e

C sta Iron

B o er Pu el w ll y

C sta Iron

RPM

R eang

S 5 d SF an F7 SF an F8 d S 9 SF10

BELT LEN THG

B S D OA E N

M T F AMEO OR R

H 4 T - 4B7 1630 1232 B39 B 3

H T - 4B57 1329 1005 B 1 B44

H T - 4B67 1121 8 8 B43 B46

H T - B77 969 733

B B 8 B5244 4

H T 4 - 4B87 85 6 5 B46 B49 B54

H T - 4B97 763 577 B 8 B51 B56

H T - B107 690 521 B50 B53 B58

H T - 4B117 629 76 B51 B55 B59

H T - 4B127 578 37 B53 B55 B61

H T - 4 4B137 535 0 B55 B58 B63

HB157T 466 352 B59 B62 -

H T - B187 390 295 B65 B68

H TB77

756 568 - -- --

B51

H TB87

667 500 - -- --

B53

H TB97

596 7 - 44 -- --

B55

H TB107

538 0 - 4 4 -

- --

B56

H TB117

4 - -- --91 368

B58

H TB127

4 - -- --52 339

B60

H TB137

4 - 18 314 -- --

B62

H TB157

36 3724 - -- -- --

H T 4 - 4 -- -- --B87 85 6 5

H TB97

763 577 - -- -- --

H TB107

690 521 - -- -- --

H TB117

629 76 - 4 -- -- --

H TB127

578 37 - 4 -- -- --

H TB137

535 0 - 4 4 -- -- --

H TB157

4 - -- -- --66 352

H TB187

390 295 - -- -- --

H TB117

828 686 - --

-- --

H TB127

756 618 - -- -- --

H TB137

697 575 - -- -- --

H TB157

616 509 - -- -- --

12 2B.4 X

830 700 - -- -- --

13 6 2B. X

759 631 - -- -- --

D O.D. "8600 6

DOUB GROOLE VE

213 215, T

F AMER

IVL44

O.D. 4. "15

4 F AME 8 R

(ADD " FO F AME) 1 R 56 R

MODELS SF 10

1315 R4 , 4 T F AME

8325

O.D. . "3 25

1 3 1 54 T & 4 T

F AMER

8 004

O.D. 4. "15

182 18 R, 4T F AME

(DEDUCT " FO , 4 , 2 R 56 1 3

& 4 T)1 5

8550

O.D. . "5 35

182 18 R, 4T F AME

(DEDUCT " FO , 4 , 2 R 56 1 3

& 4 T)1 5

BELT DRIVE SUPPLY FANS

2017 Page 2 of 4

MOTOR, PULLEYS & BELTS (See Table below)

WARNING

EXCESSIVE BELT TENSION IS THE MOST FREQUENT CAUSE OF BEARING WEAR AND RESULTING NOISE.

PROPER BELT TENSION IS CRITICAL FOR QUIET EFFICIENT OPERATION.

Ideal belt tension is the lowest value under which belt slip will not occur at peak load conditions.

BELT ALIGNMENT

FIGURE 1

X X

FOR FRACTIONAL HP APPLICATIONS "4L" BELTS MAY BE SUBSTITUTED BY ADDING 2" TO THE SPECIFIED "B" BELTS. Eg. B50 BELT = 4L52

Produkt Specifikationer

Mærke:	NAKS
Kategori:	Emhætte
Model:	SF11-3PH

Har du brug for hjælp?

Hvis du har brug for hjælp til NAKS SF11-3PH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Emhætte NAKS Manualer

15 Juni 2025

14 Juni 2025

13 Juni 2025

13 Juni 2025

13 Juni 2025

13 Juni 2025

12 Juni 2025

Emhætte Manualer

Nyeste Emhætte Manualer

Witt Chubby WHITE Manual

30 Juli 2025

Witt Architect Free Brass-3 Manual

30 Juli 2025

SVAN SCPT901AX Manual

30 Juli 2025

SVAN SCPT601AIX Manual

30 Juli 2025

SVAN SCPP601BX Manual

30 Juli 2025

SVAN SCPE602AX Manual

30 Juli 2025

SVAN SCPD601AN Manual

30 Juli 2025

Witt Architect Free Matte Black-3 Manual

30 Juli 2025

Witt Circle Wall CN Manual

29 Juli 2025

Witt Breeze 90W Manual

29 Juli 2025