Nemco 55727-8 Manual


Læs gratis den danske manual til Nemco 55727-8 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Nemco 55727-8, eller vil du spørge andre brugere om produktet?

Side 1/2
Operating and Maintenance Instructions
Easy FryKutter
Model: 55450-1 ¼ Cut 55450-4 4 Section Wedge
55450-2 3/8 Cut 55450-6 6 Section Wedge
55450-3 ½ Cut 55450-8 8 Section Wedge
1
IMPORTANT
1. To get the best operation and life from your machine, please read and comply with these instructions.
2. Clean machine thoroughly before and after each use using cleaning instructions below.
3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.
SAFETY INSTRUCTIONS
Remember that the blades are VERY SHARP! Be careful when handling and operating the machine to keep hands away
from the BLADES.
PREPARATION
1. The FryKutterproduce cutter can be mounted on a tabletop or wall, or if portability is a concern it can be mounted on a board
to be clamped to a tabletop for use.
2. If this machine replaces one used previously, it is probable that existing mounting holes can be used. If not:
a) TO WALL MOUNT. Position the machine on the wall where desired. Find a wall stud nearest the position and move the
machine so mounting holes on one side of it is over the stud. Mark 4 hole locations and remove the machine. Drill 5/32
diameter holes in these marked locations. Drive the mounting screws with washers under their heads through the
mounting holes in the machine and into the holes in the wall.
NOTE: It is important to mount this machine on a stud or very sturdy wall to prevent its falling while in use. The
mounting screws provided are long to be able to pass through wallboard, etc. and to engage sturdy material.
b) TO TABLE MOUNT. Select a solid, sturdy table or work surface to mount this machine on. Position the machine and mark
4 hole locations for mounting. Remove the machine and drill 4 holes as marked use 5/32 diameter holes if mounting
screws are to be used. If other fasteners (not furnished) are preferred, drill holes (1/4diameter maximum) as appropriate.
Use washers under the heads of screws selected.
NOTE: This also applies if the machine is to be mounted on a board for portability.
3. If unit fails to operate properly when first used call NEMCO customer service at 1-800-782-6761.
OPERATION OF Easy FryKutter
1. Place prepared produce on the BLADE & HOLDER ASSEMBLY.
2. Remove hands and fingers from the cutting area.
3. With one quick motion pull down on LEVER to cut produce. Occasionally if the produce is very large, or if it is positioned at an
angle to the blades, this may have to be repeated to cut it entirely through.
CAUTION: Do not attempt to chop produce larger than the opening in the BLADE HOLDER.
4. Clean the machine after cutting is completed, using cleaning instructions below.
5. NOTE: Since BLADE AND HOLDER ASSEMBLIES for different sized cuts are interchangeable, you may have more than one set
available for use. Before cutting be sure that the PUSH BLOCK is the correct one to use for the cutting size desired. Gently
lower the PUSH BLOCK onto the BLADE AND HOLDER ASSEMBLY to see that the PUSH BLOCK GUIDE rests on the ORINGS.
If it does not, something is wrong and must be corrected before chopping produce.
6. To cut ¼and ½use ¼PUSH BLOCK.
7. To cut 3/8use 3/8PUSH BLOCK.
TO CLEAN THE FryKutter
1. Remove THUMB SCREWS to release PUSH BLOCK.
2. Remove WING NUTS to release the BLADE AND HOLDER ASSEMBLY or BLADE HOLDER and carefully remove them.
NOTE: The PUSH BLOCK will come off with these parts so be alert so it doesnt fall.
3. Thoroughly wash the PUSH BLOCK and the BLADE AND HOLDER ASSEMBLY or BLADE HOLDER and BLADE.
4. The BLADE AND HOLDER ASSEMBLY may also be totally disassembled for further cleaning as follows:
a) Remove THUMB SCREWS and the BLADE HOLDER PLATE.
b) Gently tap the BLADES and the BLADE SPACERS from the BLADE HOLDER.
5. To reassemble:
a) Place the BLADE HOLDER on a table top with the BLADE SPACER pockets upward.
b) Insert the 4 BLADE SPACERS with their slots toward the inner opening of the BLADE HOLDER.
c) Insert BLADES with sharp edge downward and slots upward.
d) Insert BLADES with sharp edge and slots downward.
e) Reposition BLADE HOLDER PLATE and secure with THUMBSCREWS.


Produkt Specifikationer

Mærke: Nemco
Kategori: Ikke kategoriseret
Model: 55727-8

Har du brug for hjælp?

Hvis du har brug for hjælp til Nemco 55727-8 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Nemco Manualer

Nemco

Nemco 55249 Manual

15 November 2025
Nemco

Nemco 55222A Manual

13 November 2025
Nemco

Nemco 55109 Manual

12 November 2025
Nemco

Nemco 55425 Manual

11 November 2025
Nemco

Nemco 55727-8 Manual

17 September 2025
Nemco

Nemco 6405 Manual

26 August 2025
Nemco

Nemco 6410 Manual

26 August 2025
Nemco

Nemco 6600 Manual

26 August 2025
Nemco

Nemco 6015 Manual

25 August 2025
Nemco

Nemco 6016 Manual

25 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone

Waterstone 7800 Manual

11 December 2025
Kwikset

Kwikset 258 Manual

11 December 2025
Schlage

Schlage F170 Manual

11 December 2025
Moen

Moen Align 7565EV Manual

11 December 2025
ALNO

ALNO MC10244 Manual

11 December 2025
JET

JET TAK-ZX Manual

11 December 2025
Waterstone

Waterstone 1455 Manual

11 December 2025
Laica

Laica NE2015 Manual

11 December 2025