Nemco 56600-2 Manual

Nemco Skæremaskine 56600-2

Læs gratis den danske manual til Nemco 56600-2 (2 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Nemco 56600-2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Cartridge Tomato Slicer

56600-1 3/16” Slice

56600-2 1/4” Slice

56600-3 3/8” Slice

Operating and Maintenance Instructions

Important

1. To get the best operation and life from your machine, please read and comply with these instructions.

2. Clean machine thoroughly before and after each use following the cleaning instructions below.

3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.

Safety instructions

Remember that the blades are VERY SHARP! Be careful when handling and operating the machine to keep hands

away from the blades.

Preparation

1. Set unit on a flat surface.

2. If unit fails to work properly when first operated call NEMCO customer service at 1-800-782-6761.

Operation

1. Your Cartridge Tomato Slicer comes assembled and ready to use. You may want to install the TABLE STOP for your

convenience.

2. Pull HANDLE all the way toward you and carefully place the tomato on the SLIDE BOARD between the PUSHER

PLATES and the BLADES. CAUTION: SHARP BLADES

3. Withdraw your hand. With one quick motion, push the HANDLE toward the BLADES and catch the tomato in your

hand or container.

4. Remove the sliced tomato from the SLIDE BOARD and repeat the procedure for the next tomato to be sliced.

Cleaning

NOTE: Proper maintenance plays an important part in the life span and functioning of the unit.

Clean machine thoroughly after each use.

1. Be careful of the sharp blades.

2. Remove the CARTRIDGE BLADE ASSEMBLY by loosening the CLAMPING KNOBS and lifting the BRIDGE off the

BLADE ASSEMBLY. The BLADE ASSEMBY can now be lifted up and off the GUIDE RODS. (NOTE: When replacing the

BLADE ASSEMBLY, it will only fit on the machine properly one way. Be sure that the notch in the BLADE

ASSEMBLY is aligned with the protrusion in the FRAME.)

3. To remove the PUSHER ASSEMBLY for cleaning, remove the THUMB SCREWS and the SLIDE STOP and pull the

PUSHER off the end of the SLIDE BOARD.

4. Wash with a brush using soap or mild detergent and water.

5. Immediately after cleaning, a sanitizer may be used. Be sure to read and follow sanitizer manufacturer instructions.

Sanitizer must be food safe and for use with Aluminum, Stainless and HDPE plastics

6. To re-assemble, reverse the procedure.

NOTICE: Always rinse the TOMATO SLICER in cold or lukewarm water after it has been washed in hot water!

(Hot water will make the SLIDE BOARD expand and may make it hard to push the PUSHER ASSEMBLY until the

SLIDE BOARD returns to room temperature.)

IMPORTANT: NEMCO recommends occasional application of mineral oil in the grooves of the slide board.

DO NOT USE ANY TYPE OF COOKING OIL – The GUIDE PLATE will cease up on the SLIDE BOARD.

Produkt Specifikationer

Mærke:	Nemco
Kategori:	Skæremaskine
Model:	56600-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Nemco 56600-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skæremaskine Nemco Manualer

14 November 2025

14 November 2025

12 November 2025

12 November 2025

Nemco Monster Airmatic 56455-3 Manual

11 November 2025

11 November 2025

27 August 2025

27 August 2025

27 August 2025

27 August 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Maestro MR-590 Manual

8 December 2025

Maestro MR-591 Manual

8 December 2025

Omcan 11399 Manual

5 December 2025

Vevor SK-720L Manual

2 December 2025

Vevor PGYHJ3626 Manual

2 December 2025

Lakeland 62167 Manual

2 December 2025

Vevor PGYHJ2814 Manual

1 December 2025

Vevor PGYHJ2615 Manual

30 November 2025

Sommertal AS170 Manual

30 November 2025

Vevor AY490-1 Manual

30 November 2025