Nemco 57500-1 Manual

Nemco Skæremaskine 57500-1

Læs gratis den danske manual til Nemco 57500-1 (2 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Nemco 57500-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Easy Chopper 3

Model: 57500-( )

OPERATING AND MAINTENANCE INSTRUCTIONS

Important

1. To get the best operation and life from your Easy Chopper 3, please read and comply with these instructions.

2. Clean machine thoroughly before first use and after each use using cleaning instructions below.

3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.

Safety Instructions

Remember that the blades are VERY SHARP; be careful when handling and operating the equipment to keep hands

away from the cutting edges.

Operation of Easy Chopper 3

1. Always check the equipment before each use to ensure that it is clean & free of debris. Also inspect the blades to ensure

there are no broken, nicked, or dulled blades and if found, replace the blade assembly before using the equipment again.

2. Place the chopper on a firm, clean, and flat work surface.

3. Be sure that the cleaning gasket is in place before using. Also, ensure that the color of the push block matches the colored

indicator on the blade assembly to confirm they are a matching set.

4. Prepare the produce to be cut (Chopped, Sliced, or Wedged).

5. Lift HANDLE and place the produce on the blades with the flat side down.

6. Remove hand/fingers from the cutting area, use free hand to grasp the leg of the frame, and with a strong, quick thrust,

bring the PUSH BLOCK down to force the produce through the BLADES. Lift and repeat.

7. Clean the machine after prep work is completed using cleaning instructions below.

Caution: Do not attempt to chop produce larger than the opening in the BLADE HOLDER (4- -1/4” x 4 1/4”).

Note: Additional blade and PUSH BLOCK sets can be purchased separately. Be sure to always use a PUSH BLOCK and blade set

that are compatible or damage to the equipment will result. To check for compatibility, compare the color of the push block to the

colored indicator on the blade assembly. The color of the cleaning gasket should match the push block and blade assembly as

well.

To Clean

1. Remove the PUSHER assembly off the GUIDE RODS. Using the tabs on the cleaning gasket, pull the cleaning gasket from

the push block to remove debris from the slots.

2. Remove the blade assembly from the locating pins.

3. Thoroughly wash the PUSHER & BLADE assemblies, and cleaning gasket using warm water and a mild detergent.

CAUTION: Do not wipe across the sharp side of the blades, or use abrasive pads on the blades. Wiping across the sharp

side of the blades in any form may cause injury and will dull the blades.

4. To aid cleaning, spray pressurized water across the blade assembly from the dull side to force out debris. Pressurized water

can also be sprayed on the push block to force out remaining debris.

5. Allow all pieces to air dry.

6. Once all pieces are dry, reassemble the components to the Chopper. It is suggested that mineral oil is applied to the guide

rods every time the equipment is cleaned.

Chopping Tips

Cut produce before chopping and place a cut surface against the BLADES. Onions and tomatoes dice best if cut from top to

bottom. They may be cut in half, or if smaller dices are desired, they can be cut several times in this direction.

To Lubricate

When needed, lubricate the GUIDE RODS with Mineral Oil, Food Grade Lubricant, or rub them with Paraffin.

DO NOT LUBRICATE WITH COOKING OIL IT GETS STICKY! –

Produkt Specifikationer

Mærke:	Nemco
Kategori:	Skæremaskine
Model:	57500-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Nemco 57500-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skæremaskine Nemco Manualer

14 November 2025

14 November 2025

12 November 2025

12 November 2025

Nemco Monster Airmatic 56455-3 Manual

11 November 2025

11 November 2025

27 August 2025

27 August 2025

27 August 2025

27 August 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Maestro MR-590 Manual

8 December 2025

Maestro MR-591 Manual

8 December 2025

Omcan 11399 Manual

5 December 2025

Vevor SK-720L Manual

2 December 2025

Vevor PGYHJ3626 Manual

2 December 2025

Lakeland 62167 Manual

2 December 2025

Vevor PGYHJ2814 Manual

1 December 2025

Vevor PGYHJ2615 Manual

30 November 2025

Sommertal AS170 Manual

30 November 2025

Vevor AY490-1 Manual

30 November 2025