Netgear WG103 Manual

Netgear Adgangspunkt WG103

Læs gratis den danske manual til Netgear WG103 (2 sider) i kategorien Adgangspunkt. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Netgear WG103, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

)NSTALLATION'UIDE

Please refer to the Reference Manual on your Resource CD for instructions about

advanced configuration options.

Estimated Installation Time: 30 minutes.

Tip: Before mounting the WG103 in a high location, first set up and test the WG103 to

verify wireless network connectivity.

1. Connect the WG103 to the Computer

a. Unpack the box and verify the contents.

b. Prepare a PC with an Ethernet

adapter. If this PC is already part

of your network, record its

TCP/IP configuration settings.

Configure the PC with a static IP

address of 192.168.0.210 and

255.255.255.0 as the subnet mask.

c. Connect an Ethernet cable from

the WG103 to the PC (point A in

the illustration).

d. Securely insert the other end of the

cable into the WG103 Ethernet

port (point B in the illustration).

e. Turn on your computer, connect the power adapter to the WG103 and verify the

following:

• Power: The power light should be lit. If the power light is not lit, check the

connections and check to see if the power outlet is controlled by a wall

switch that is turned off.

• Test: The test light should be blinking when the WG103 is first turned on.

• LAN: The LAN light should be lit (amber for a 10 Mbps connection and

green for a 100 Mbps connection). If not, make sure the Ethernet cable is

securely attached at both ends.

2. Configure LAN and Wireless Access

a. Configure the WG103 Ethernet port for LAN access.

• Connect to the WG103 by opening your browser and

entering http://192.168.0.229 in the address field.

• When prompted, enter admin for the user name and

password for the password, both in lower case letters.

• Click the Basic Settings link and configure the IP Settings for your network.

b. Configure the wireless interface for wireless access. See the online help or the

Reference Manual for full instructions.

c. Test wireless connectivity using a PC with a wireless adapter configured

according to the wireless settings you just set in the WG103 to establish a

wireless connection to the WG103.

Now that you have finished the setup steps, you are ready to deploy the WG103 in

your network. If needed, you can now reconfigure the PC you used in step 1 back to

its original TCP/IP settings.

1. Disconnect the WG103 and position it where you will deploy it. The best location is

elevated, such as wall mounted or on the top of a cubicle, at the center of your

wireless coverage area, and within line of sight of all the mobile devices.

2. Position the antenna. Vertical positioning provides best side-to-side coverage.

Horizontal positioning provides best top-to-bottom coverage.

3. Connect an Ethernet cable from your WG103 to a LAN port on your router, switch, or

hub.

4. Connect the power adapter to the wireless access point and plug the power adapter in

to a power outlet. The Power and LAN lights should light up.

Tip: The WG103 supports Power Over Ethernet (PoE). If you have a switch that

provides PoE, you will not need to us to power the WG103. e the power adapter

This can be especially convenient when the WG103 is installed in a high

location far away from a power outlet.

Using a computer with an 802.11g or 802.11b wireless adapter, verify connectivity by

using a browser such as Internet Explorer or Mozilla Firefox to

connect to the Internet, or

check for file and printer access on your network. In order to connect to the Internet, your

network must include a router that provides Internet access.

Note: If you cannot connect, see to Troubleshooting Tips in this guide or the Reference

Manual on the Resource CD for the ProSafe® 802.11g Wireless Access Point.

WG103_IG.fm Page 1 Monday, March 30, 2009 12:45 PM

March, 2009

This symbol was placed in accordance with the European Union Directive 2002/96 on

the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of

within the European Union, this product s cled in accordance hould be treated and recy

with the laws of your jurisdiction implementing the WEEE Directive.

trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product

names are trademarks or registered trademarks of formation is subject to their respective holders. In

change without notice.

Here are some tips for correcting simple problems you may have.

The wireless access point has no power:

• Make sure the power cord is connected to the access point and plugged in to a

working power outlet or power strip.

• Make sure you are using the correct NETGEAR power adapter supplied with your

access point.

There is a hardware connection problem:

• Make sure the cable connectors are securely plugged in at the access point and the

network device (hub, switch, or router).

• Make sure the connected device is turned on.

The wireless access point’s antennas are not working:

• If the Wireless LAN activity light stays off while the WG103 is transmitting or

receiving data, disconnect the adapter from en plug it in again.its power source and th

• Make sure the antennas are tightly connected to the WG103.

• Contact NETGEAR if the Wireless LAN light remains off while the WG103 is

transmitting or receiving data.

Check these items:

• The WG103 is properly installed, LAN connections are OK, and it is powered on.

Check that the LAN port LED is green to verify that the Ethernet connection is OK.

• If you are using the NetBIOS name of the WG103 to connect, ensure that your PC

and the WG103 are on the same network segm a WINS server on ent or that there is

your network.

• If your PC uses a fixed (static) IP address, ensure that it is using an IP address in the

range of the WG103. The WG103 default IP address is 192.168.0.229 and the default

subnet mask is 255.255.255.0. The WG103 default setting is for a static IP address.

• If the network where you are connecting it is using DHCP, configure it accordingly.

See the Reference Manual on the for the ProSafe® 802.11g Wireless Resource CD

Access Point for more details.

There is a configuration problem. Check these items:

• You may not have restarted the computer with the wireless adapter to have TCP/IP

changes take effect. Restart the computer.

• The computer with the wireless adapter may not have the correct TCP/IP settings to

communicate with the network. Restart the computer and check that TCP/IP is set up

properly for that network. The usual setting for Windows on the Network Properties

is set to “Obtain an IP address automatically.”

• The WG103’s default values may not work with your network. Check the WG103

default configuration against the configuration of other devices in your network.

• For full instructions on changing the access point’s default values, see the

Reference Manual on the Resource CD for the ProSafe® 802.11g Wireless Access

Point.

Thank you for selecting NETGEAR products.

After completing the Smart Wizar e the serial number on the d configuration assistant, locat

bottom label of your product, and use it to register your product at

http://www.NETGEAR.com/register.

Registration is required before you can use our telephone support service. Registration via

our website is strongly recommended. Go to http://kbserver.netgear.com for product

updates and Web support For Warranty and Regional Customer Support information, see .

the Resource CD that came with your product.

WG103_IG.fm Page 2 Monday, March 30, 2009 12:45 PM

Produkt Specifikationer

Mærke:	Netgear
Kategori:	Adgangspunkt
Model:	WG103
Vægt:	402.5 g
Ethernet LAN-porte (RJ-45):	1
Strømforbrug (typisk):	5 W
Ethernet LAN-datahastigheder:	10,100 Mbit/s
Sikkerhedsalgoritmer:	128-bit WEP,64-bit WEP,802.1x RADIUS,WPA-PSK,WPA2-PSK
Intern hukommelse:	32 MB
Dimensioner (BxDxH):	158 x 29 x 101 mm
Webbaseret administration:	Ja
Servicekvalitet support (QoS):	Ja
LED-indikatorer:	Ja
AC-adapter inkluderet:	Ja
Kabellængde:	100 m
Antal brugere:	30 bruger(e)
Slot til kabellås:	Ja
Frekvensbånd:	2.4 GHz
Grænseflade:	LAN, WLAN
Maksimal dataoverførselshastighed:	108 Mbit/s
Processormodel:	Qualcomm Atheros
Strøm-LED:	Ja
Overfører strømområde:	20 dBm dBmW
Kabellåseslids type:	Kensington
Flashhukommelse:	8 MB
Strøm over Ethernet (PoE):	Ja
Indbygget processer:	Ja
VLAN understøttelse:	Ja
Filtrering af MAC-adresser:	Ja
2.4 GHz:	Ja
Overholdelse af branchestandarder:	802.11i, 802.1x, 802.3af
Niveau for antennestyrke (maks.):	5 dBi
Antennestik type:	SMA
Gennemløbs datahastighed:	54 Mbit/s
Trådløs standard:	IEEE 802.11g
Logning og overvågning:	SNMP v1, v2c