Noctua NH-P1 Manual

Noctua Hardwarekoeling NH-P1

Læs gratis den danske manual til Noctua NH-P1 (6 sider) i kategorien Hardwarekoeling. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Noctua NH-P1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Place the backplate on the rear side of the motherboard so that the

bolts stick through the mounting holes.

Caution: Please make sure that the three cut-outs in the

supplied backplate align with the screws of the motherboard’s

stock backplate.

First put the plastic spacers onto the bolts of the backplate, then

add the NM-IMB2 mounting bars.

Installing the mounting bars3

Noctua NH-P1|

Installation manual

Scan this code to display

multilingual manuals on

you mobile phone.

While the NH-P1 provides first-rate performance for a passive

cooler, it is not suitable for overclocking or CPUs that create high

heat-loads. Please note that the TDP (Thermal Design Power)

rating or amount of heat dissipation that the cooler can handle

not only depends on the chassis and various other factors such as

ambient temperature or other components inside the system, but

also generally varies from CPU model to CPU model.

For this reason, we specify cooling performance using the

Noctua Standardised Performance Rating (NSPR) instead of

giving a general TDP specification. In addition, we refer to our

CPU compatibility list where we indicate how well the cooler can

be expected to work on a particular CPU in a fully optimised

setup (see our setup guidelines):

https://ncc.noctua.at/s/nh-p1-cpus

If necessary, Noctua recommends adding a near-inaudible

120mm fan like the NF-A12x25 LS-PWM to the heatsink for

improved performance headroom.

Dear customer,

Congratulations on choosing the Noctua NH-P1.

The NH-P1 is Noctua’s first passive CPU cooler and has been

custom-designed for fanless operation from ground up: In

enclosures with good natural convection, its six heatpipes and

thick, widely spaced heatsink fins enable it to cool modern

high-end CPUs with low to moderate heat dissipation

completely passively. Please take a look at our setup guidelines

in order to make sure that you will get optimal results.

Enjoy your NH-P1!

Yours sincerely,

Roland Mossig, Noctua CEO

This manual will guide you through the installation process of the

SecuFirm2+™ mounting system step by step.

Prior to installing the cooler, please consult the compatibility list

on our website (www.noctua.at/compatibility) and verify that the

cooler is fully compatible with your motherboard.

Please also make sure that your PC case offers sufficient clearance

for the cooler and that there are no compatibility issues with any

other components (e.g. tall RAM modules).

Double check that the heatsink and fan clips do not make

contact with the VGA card or other PCIe cards.

Noctua cannot be held responsible for any damage or losses caused

by compatibility issues. Should you encounter any difficulties,

please check the FAQs on our website (www.noctua.at/faqs) and

don’t hesitate to contact our support team at support@noctua.at.

Multilingual versions of this manual are available on our website:

www.noctua.at/manuals

LGA115x & LGA1200

Caution: In order to get optimal results when building passively

cooled systems using the NH-P1, it is important to follow some

general guidelines.

Please refer to the following page for detailed guidelines and

recommendations on how to set up your system for best results:

https://noctua.at/en/nh-p1-setup-guidelines

The NH-P1 strictly requires either a fanless PC case with good

natural convection, an open benchtable type setup or a PC case

with fans in order to achieve its full performance.

We offer a list of recommended cases for completely fanless

systems using the NH-P1:

https://ncc.noctua.at/s/nh-p1-case-recommendations

Required mounting parts:

4x NM-ITS1-TX

thumb screws

4x NM-IPS1

plastic spacers

1x NM-IBP2

backplate

2x NM-IMB2

mounting bars

In case you want to use the cooler on an assembled system and

your case doesn’t have a cut-out at the rear side of the mother-

board tray, you first have to remove the motherboard from the

case in order to be able to install the supplied backplate.

Removing the motherboard1

Caution: The supplied backplate will install over the mother-

board’s stock backplate, so the motherboard’s stock backplate

must not be taken off.

Attaching the backplate2

Caution: Choose the alignment of the mounting bars according to the

desired final orientation of the cooler:

Caution: Make sure that the curved sides of the mounting bars are

pointing outwards.

Orientation A Orientation B

Produkt Specifikationer

Mærke:	Noctua
Kategori:	Hardwarekoeling
Model:	NH-P1
Type:	Heatsink/Radiatior
Bredde:	158 mm
Dybde:	154 mm
Højde:	152 mm
Vægt:	1180 g
Antal pr. pakke:	1 stk
Produktfarve:	Aluminium
Pakkevægt:	1974 g
Pakkedybde:	194 mm
Pakkebredde:	194 mm
Pakkehøjde:	224 mm
Materiale:	Aluminium, Copper
Harmoniseret systemkode (HS):	84733080
Monteringssæt:	Ja
Passende til rumtype:	Processor
Ventilator diameter:	Ingen mm
Kompatibel processor serie:	AMD A, AMD Athlon, AMD Ryzen 3, AMD Ryzen 5, AMD Ryzen 7, AMD Ryzen 9 3rd Gen, Intel Celeron, Intel Core i3, Intel Core i5, Intel Core i7, Intel Core i9, Intel Pentium
Understøttede procesorsokler:	LGA 1150 (Socket H3), LGA 1151 (Socket H4), LGA 1155 (Socket H2), LGA 1156 (Socket H), LGA 1200 (Socket H5), LGA 2011 (Socket R), LGA 2011-v3 (Socket R), LGA 2066, Socket AM2, Socket AM2+, Socket AM3, Socket AM3+, Socket AM4, Socket FM1, Socket FM2, Socket FM2+
Materiale for grundplade:	Kobber