NuTone 665RP Manual

NuTone Ventilator 665RP

Læs gratis den danske manual til NuTone 665RP (12 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 13 anmeldelser. Har du et spørgsmål om NuTone 665RP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

MODEL 665RP

Page 1

HEATER / FAN / LIGHT

READ AND SAVE THESE INSTRUCTIONS

To register this product, visit:

www.nutone.com

IMPORTANT INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE INSTALLING

OR USING THIS HEATER.

To reduce the risk of fire, electric shock, or injury to persons, observe

the following:

1. Use this unit only in the manner intended by the manufacturer. If you

have questions, contact the manufacturer at the address or tele-

phone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel

and lock the service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning de-

vice, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction codes and standards.

4. When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

5. This heater is hot when in use. To avoid burns, do not let bare skin

touch hot surfaces. Keep combustible materials, such as furniture,

pillows, bedding, papers, clothes, etc. and curtains at least 3 feet

(0.9 m) from the front of the heater.

6. Extreme caution is necessary when any heater is used by or near

children or invalids and whenever the heater is left operating and

unattended.

7. Do not operate any heater after it malfunctions. Disconnect power at

service panel and have heater inspected by a reputable electrician

before reusing.

8. Do not use outdoors.

9. To disconnect heater, turn controls to off, and turn off power to heat-

er circuit at main disconnect panel (or operate internal disconnect

switch, if provided).

10. Do not insert or allow foreign objects to enter any ventilation or ex-

haust opening, as this may cause an electric shock or fire, or dam-

age the heater.

11. To prevent a possible fire, do not block air intakes or exhaust in any

manner.

12. A heater has hot and arcing or sparking parts inside. Do not use it

in areas where gasoline, paint, or flammable vapors or liquids are

used or stored.

13. Use this heater only as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock,

or injury to persons.

14. This product must be grounded.

15. Do not install heater in a tub or shower enclosure.

16. This product is designed for ceiling installation only. This product

is designed for installation in ceilings up to a12/12 pitch. Ductwork

must point up. DO NOT MOUNT THIS PRODUCT IN A WALL.

17. Install heater at least 12 inches from floor or any adjacent wall.

18. Do not connect heater to dimmer switch or speed control.

19. Provide a separate 20 AMP circuit. Use 12 GA. power cable of type

which meets code. Use supply wiring rated for at least 90

20. For greatest efficiency, install heater so heat is directed toward tub

or shower area. Avoid directing toward walls or windows.

SAVE THESE INSTRUCTIONS

PREPARATION

1. Remove the lamp

holder assembly.

2. Remove the heater

assembly retaining

screw.

3. Rotate heater assembly

and lift it up and out of the

housing.

4. Remove fan assembly

retaining screws. Lift

fan assembly out of the

housing.

5. Slide the 4 hanger

bars into the slots

on each end of the

housing - 2 hanger

bars per side.

MODEL 665RP

Page 2

For best results, choose a

location which allows fan to

be vented outside with the

shortest possible duct run

and the fewest number of

elbows.

1. Position unit between

joists and extend mount-

ing brackets. Position

brackets such that the

bottom edge of housing will be flush with finished ceiling.

Mark the top of keyhole slot on all four mounting brackets.

INSTALLATION

2. Remove unit tem-

porarily, and pound

nails partially into

joists at all four

marked locations.

3. Hang unit from nails and

check if unit will be flush with

finished ceiling. Pound nails

tight. For wide joist centers:

A #8 x 3/8 self-tapping screw

can be used to join extended

brackets together and cre-

ate a rigid mount. To ensure

a noise-free mount, crimp

the bracket channels tightly

around mounting brackets.

WARNING: To reduce the risk of fire, do not store or use

gasoline or other flammable vapors and liquids in the vicin-

ity of the heater.

CAUTION: High temperature, risk of fire, keep electrical cords,

drapery, furnishings, and other combustibles at least 3 feet

(0.9 m) from the front of the heater and away from the side

and rear.

Produkt Specifikationer

Mærke:	NuTone
Kategori:	Ventilator
Model:	665RP

Har du brug for hjælp?

Hvis du har brug for hjælp til NuTone 665RP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator NuTone Manualer

NuTone QTRN080L Manual

9 September 2025

5 Juli 2025

5 Juli 2025

5 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

1 Juli 2025

Ventilator Manualer

Nyeste Ventilator Manualer

LTC LXWT112 Manual

9 September 2025

LTC LXWB17 Manual

9 September 2025

Waves FAN-105062 Manual

9 September 2025

LTC LXGA30 Manual

9 September 2025

LTC LXWT28 Manual

9 September 2025

FAR SFT2723 Manual

9 September 2025

ActiveJet WKS-120BPJ Manual

9 September 2025

House Of Marley Classic C10 Manual

9 September 2025

House Of Marley Classic C21 Manual

9 September 2025

House Of Marley Classic C20 Manual

8 September 2025