NuTone 765HL Manual

NuTone Ventilator 765HL

Læs gratis den danske manual til NuTone 765HL (12 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 13 anmeldelser. Har du et spørgsmål om NuTone 765HL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

Page 1

MODEL 765HL

VENTILATION FAN

WITH HEATER & LIGHT

READ AND SAVE THESE INSTRUCTIONS

www.nutone.com/register

IMPORTANT INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE INSTALLING OR

USING THIS HEATER.

To reduce the risk of fire, electric shock, or injury to persons, observe the

following:

1. Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer at the address or telephone number

listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and

lock the service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a prominent warning device, such as a tag, to

the service panel.

3. Installation work and electrical wiring must be done by a qualified

person(s) in accordance with all applicable codes and standards, includ-

ing fire-rated construction codes and standards.

4. When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

5. This heater is hot when in use. To avoid burns, do not let bare skin touch

hot surfaces. Keep combustible materials, such as furniture, pillows, bed-

ding, papers, clothes, etc. and curtains at least 3 feet (0.9 m) from the

front of the heater.

6. Extreme caution is necessary when any heater is used by or near chil-

dren or invalids and whenever the heater is left operating and unattended.

7. Do not operate any heater after it malfunctions. Disconnect power at ser-

vice panel and have heater inspected by a reputable electrician before

reusing.

8. Do not use outdoors.

9. To disconnect heater, turn controls to off, and turn off power to heater

circuit at main disconnect panel (or operate internal disconnect switch, if

provided).

10. Do not insert or allow foreign objects to enter any ventilation or exhaust

opening, as this may cause an electric shock or fire, or damage the heat-

er.

11. To prevent a possible fire, do not block air intakes or exhaust in any man-

ner.

12. A heater has hot and arcing or sparking parts inside. Do not use it in

areas where gasoline, paint, or flammable vapors or liquids are used or

stored.

13. Use this heater only as described in this manual. Any other use not rec-

ommended by the manufacturer may cause fire, electric shock, or injury

to persons.

14. This product must be grounded.

15. Do not install heater in a tub or shower enclosure.

16. THIS PRODUCT MUST BE MOUNTED IN A FLAT CEILING ONLY. In-

stallations in ceilings 9-feet high or less will provide maximum comfort.

DO NOT MOUNT THIS PRODUCT IN A WALL.

17. Install heater in ceiling only - at least 6 inches from any wall.

18. Do not connect heater to dimmer switch or speed control.

19. Provide a separate 20 AMP circuit. Use 12 GA. power cable of type which

meets code. Use supply wiring rated for at least 90

20. For greatest efficiency, install heater so heat is directed toward tub or

shower area. Avoid directing toward walls or windows.

SAVE THESE INSTRUCTIONS

PLAN THE INSTALLATION

The unit will operate most quietly and efficiently when located

where the shortest possible duct run and minimum number of

elbows will be needed.

Use a roof cap or wall cap that has a built-in damper to reduce

backdrafts.

Plan to supply the unit with proper line voltage and appropriate

power cable.

ROOF

CAP

4-IN. ROUND

ELBOW(S)

4-IN.

ROUND

DUCT

WALL

CAP

Purchase

separately

INSULATION

(Can be placed

around and over

housing.)

HOUSING

TYPICAL INSTALLATION

HOUSING

CEILING

JOIST, TRUSS,

OR I-JOISTS

MOUNTING

CHANNELS

GRILLE

CEILING

MATERIAL

POWER

CABLES

Housing mounted to joists, trusses, or I-joists.

Up to 24-inches on-center.

Page 2

MODEL 765HL

INSTALLATION

2. Mount housing.

Extend hanger bars to the width of the framing. Hold fan

in place with the hanger bar tabs wrapping around the

bottom edge of the framing.

Nail fan to framing or fasten with screws (not provided)

through near nails.holes

* To ensure a noise-free mount: Secure hanger bars

together with screws or use a pliers to crimp mounting

channels tightly around hanger bars.

1. Insert hanger bars.

Four (4) sliding are provided to allow for hanger bars

accurate positioning of housing anywhere between

framing. They can be used on all types of framing (I-joist,

standard joist, and truss construction) and span up to 24”.

Slide hanger bars into on housing. Make sure channels

hanger bar face “up” as shown.tabs

3. Attach

damper

/ duct

connector to

housing.

Snap damper /

duct connector

onto housing.

Make sure

connector is flush

with top of housing

and damper flap

falls closed.

TAB

CHANNEL

HANGER

BARS

HANGER

BARS

CHANNEL

BOTTOM EDGE

OF FRAMING

* SCREW (2)

HOLE FOR OPTIONAL

SCREW MOUNTING (4)

NAIL (4)

WARNING: To reduce the risk of fire, do not store or use

gasoline or other flammable vapors and liquids in the vicinity

of the heater.

CAUTION: High temperature, risk of fire, keep electrical cords,

drapery, furnishings, and other combustibles at least 3 feet

(0.9 m) from the front of the heater and away from the side

and rear.

CONNECT WIRING

GREEN

WHITE

HEAT

LIGHT

GROUND

120 VAC LINE IN

BLACK

FAN

RED

WIRING PLATE

FROM VENTILATOR

VENTILATOR

HOUSING

LIGHT

FANHEAT

BLACK to BLACK

(Fan)

WHITE to WHITE

RED to BLUE

(Light)

BLACK to RED

(Heat)

WHITE to WHITE

BLACK

CAUTION

RATING

SPECIFICATIONS

Each two-position

rocker switch is rated 15

A @ 120VAC. The total

load on this control must

not exceed 20 A @ 120VAC.

4. Install

4-inch round

ductwork.

Connect 4-inch

round ductwork

to damper / duct

connector. Run

ductwork to a roof

cap or wall cap.

Tape all ductwork

connections to

make them secure

and air tight.

Installation work and electrical wiring must be done by a quali-

fied person(s) in accordance with all applicable codes and stan-

dards, including fire-rated construction codes and standards.

Produkt Specifikationer

Mærke:	NuTone
Kategori:	Ventilator
Model:	765HL

Har du brug for hjælp?

Hvis du har brug for hjælp til NuTone 765HL stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator NuTone Manualer

NuTone QTRN080L Manual

9 September 2025

5 Juli 2025

5 Juli 2025

5 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

1 Juli 2025

Ventilator Manualer

Nyeste Ventilator Manualer

LTC LXWT112 Manual

9 September 2025

LTC LXWB17 Manual

9 September 2025

Waves FAN-105062 Manual

9 September 2025

LTC LXGA30 Manual

9 September 2025

LTC LXWT28 Manual

9 September 2025

FAR SFT2723 Manual

9 September 2025

ActiveJet WKS-120BPJ Manual

9 September 2025

House Of Marley Classic C10 Manual

9 September 2025

House Of Marley Classic C21 Manual

9 September 2025

House Of Marley Classic C20 Manual

8 September 2025