NuTone 668RP Manual

NuTone Ventilator 668RP

Læs gratis den danske manual til NuTone 668RP (8 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om NuTone 668RP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

MODEL 668RP

Page 1

WARNING

CAUTION

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-

JURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufac-

turer. If you have questions, contact the manufacturer at the

address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the ser-

vice disconnecting means cannot be locked, securely fasten

a prominent warning device, such as a tag, to the service

panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhaust-

ing of gases through the flue (chimney) of fuel burning equip-

ment to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code au-

thorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Acceptable for use over bathtub or shower when installed in

a GFCI protected branch circuit.

8. If this unit is to be installed over a tub of shower, it must be

marked as appropriate for the application and be connected

to a GFCI (Ground Fault Circuit Interrupter) protected branch

circuit.

9. Do not use this fan with any solid-state speed control device.

10. Never place a switch where it can be reached from a tub or

shower.

11. Use this unit only in the manner intended by the manufac-

turer. If you have questions, contact the manufacturer.

12. This unit must be grounded.

FAN / LIGHT

READ AND SAVE THESE INSTRUCTIONS

1. Provide a separate 15 AMP circuit. Use 14 GA. power cable

of type which meets code.

2. This product is designed for ceiling installation only. This prod-

uct is designed for installation in ceilings up to a 12/12 pitch.

Ductwork must point up. DO NOT MOUNT THIS PRODUCT

IN A WALL.

3. Install in ceiling only, at least 6” from any wall.

4. For general ventilating use only. Do not use to exhaust haz-

ardous or explosive materials and vapors.

5. To avoid motor bearing damage and noisy and/or unbal-

anced impellers, keep drywall spray, construction dust, etc.,

off power unit.

6. Please read specification label on product for further infor-

mation and requirements.

DISCONNECT ELECTRIC POWER SUPPLY BEFORE

CLEANING OR SERVICING THIS UNIT.

TO REPLACE BULB:

Remove lens by gently depressing sides and pull down. Use

bulb rated up to 100 watts only.

TO CLEAN LENS AND GRILLE:

Remove lens as explained above. Remove bulb. Remove acorn

nut in center of light reflector and lower assembly. Unplug light.

CAUTION: Grille and reflector are separate units.

Plastic parts can be cleaned with mild, soapy water and dried

with a soft cloth. DO NOT USE ABRASIVE CLOTHS, STEEL

WOOL PADS, OR SCOURING POWDERS.

TO CLEAN FAN ASSEMBLY:

Unplug fan motor. Remove retaining screws.

CAUTION: Fan assembly will swing downward when screws are

removed. Support the fan assembly with a free hand while re-

moving retaining screws.

Gently vacuum fan, motor and interior of housing. Motor is per-

manently lubricated and never needs oiling.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IM-

MERSED IN WATER.

TO REASSEMBLE ALL ABOVE PARTS:

Reverse all procedures explained above. Assemblies should not

be disassembled any further than explained above.

USE AND CARE

To register this product, visit:

www.nutone.com

MODEL 668RP

Page 2

PREPARE THE UNIT

1. Remove the lamp

holder assembly.

2. Remove fan assembly

retaining screws. Lift

fan assembly out of the

housing.

3. Slide the 4 hanger

bars into the slots

on each end of the

housing - 2 hanger

bars per side.

For best results, choose a

location which allows fan

to be vented outside with

the shortest possible duct

run and the fewest number

of elbows.

1. Position unit between

joists and extend mount-

ing brackets. Position

brackets such that the

bottom edge of housing will be flush with finished ceiling.

Mark the top of keyhole slot on all four mounting brackets.

INSTALL THE UNIT

2. Remove unit tem-

porarily, and pound

nails partially into

joists at all four

marked locations.

3. Hang unit from nails and

check if unit will be flush with

finished ceiling. Pound nails

tight. For wide joist centers:

A #8 x 3/8 self-tapping screw

can be used to join extended

brackets together and cre-

ate a rigid mount. To ensure

a noise-free mount, crimp

the bracket channels tightly

around mounting brackets.

Produkt Specifikationer

Mærke:	NuTone
Kategori:	Ventilator
Model:	668RP

Har du brug for hjælp?

Hvis du har brug for hjælp til NuTone 668RP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator NuTone Manualer

1 Juli 2025

1 Juli 2025

1 Juli 2025

1 Juli 2025

NuTone 765H110L Manual

1 Juli 2025

NuTone 763 Manual

1 Juli 2025

NuTone 696N Manual

1 Juli 2025

NuTone ChromaComfort Manual

30 August 2024

Ventilator Manualer

Nyeste Ventilator Manualer

1 Juli 2025

1 Juli 2025

1 Juli 2025

1 Juli 2025

1 Juli 2025

1 Juli 2025

1 Juli 2025

1 Juli 2025

1 Juli 2025

1 Juli 2025