NuTone 682NT Manual

NuTone Ventilator 682NT

Læs gratis den danske manual til NuTone 682NT (8 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 7 anmeldelser. Har du et spørgsmål om NuTone 682NT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

IMPORTANT SAFETY INSTRUCTIONS

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY

TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified

person(s) in accordance with all applicable codes and stan-

dards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment manufac-

turer’s guidelines and safety standards such as those published

by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Condition-

ing Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. If this unit is to be installed over a tub or shower, it

must be marked as appropriate for the application.

8. Never place a switch where it can be reached from a tub or

shower.

9. This unit must be grounded.

CAUTION

1. For general ventilating use only. use to exhaust hazardDo not -

ous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc., off power

unit.

3. Please read specification label on product for further information

and requirements.

INSTALLATION INSTRUCTIONS

READ & SAVE THESE INSTRUCTIONS!

Ductless Fan

MODEL: 682NT

PLAN THE INSTALLATION

Refer to FIGURE 1

Determine where fan will be located and plan to supply fan with

proper line voltage and appropriate power cable.

Follow these basic steps when installing this fan:

Attach mounting bracket to joist or stud.

Snap fan housing onto bracket.

Wire fan.

Attach grille (after ceiling or wall is finished).

FIGURE 1

1”

ROUGH-IN OPENING SIZE IS 7-1/4” x 7-1/4”

7-1/8”

3-3/4”

8-1/2”

7-1/8”

8-1/2”

FIGURE 7 FIGURE 8

FIGURE 6

BLACK

WHITE

TOGGLE

SWITCH

WHITE

BLACK

BLACKGROUND

SWITCH

BOX

HOUSING

120 VAC LINE IN

FIGURE 2

FIGURE 3

FIGURE 4

INSTALLATION

Refer to FIGURE 2

1. Nail mounting bracket to joist or stud. Use gauge on bracket to

locate it for 1/2” or 3/4” drywall.

Refer to FIGURE 3

2. Snap fan housing onto bracket.

Refer to FIGURE 4

3. Remove the knockout plate from fan. Break out either top or rear

electrical access hole. Insert a screwdriver into slot in knockout

and bend back and forth to break tabs.

NOTE: Turn off power and lock out service panel before installing

electrical wiring.

Refer to FIGURE 5

4. Secure power cable to knockout plate with proper connector for

type of cable being used. Allow 6” of cable to extend beyond

knockout plate. Connect ground wire to green ground screw on

knockout plate.

Refer to FIGURE 6

5. Make electrical connections. Wire white to white and black to

black.

Refer to FIGURE 7

6. Carefully tuck wiring inside wiring compartment and reattach

knockout plate.

Refer to FIGURE 8

7. Attach grille. Squeeze grille springs and insert them into slots in

motor plate. Push grille against ceiling. Grille may be papered

or painted.

USE AND CARE

CAUTION – DISCONNECT POWER AT SERVICE ENTRANCE

AND LOCK OUT PANEL BEFORE CLEANING OR SERVICING

UNIT.

Grille

Clean grille with mild soap or detergent and dry with a soft cloth.

Do not use abrasive cloth, steel wool pads, or scouring powders.

Filter

Charcoal filter is long-lasting. Each filter will last 60 to 90 days when

operated continuously, or longer depending on frequency of use.

Order replacement charcoal filter from list below.

Fan Assembly

To clean: Remove grille and filter. Gently vacuum impeller, motor

and interior of housing.

CAUTION – METAL AND ELECTRICAL PARTS SHOULD NEVER

BE IMMERSED IN WATER.

FIGURE 5

< >

Produkt Specifikationer

Mærke:	NuTone
Kategori:	Ventilator
Model:	682NT

Har du brug for hjælp?

Hvis du har brug for hjælp til NuTone 682NT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator NuTone Manualer

NuTone QTRN080L Manual

9 September 2025

5 Juli 2025

5 Juli 2025

5 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

4 Juli 2025

1 Juli 2025

Ventilator Manualer

Nyeste Ventilator Manualer

LTC LXWT112 Manual

9 September 2025

LTC LXWB17 Manual

9 September 2025

Waves FAN-105062 Manual

9 September 2025

LTC LXGA30 Manual

9 September 2025

LTC LXWT28 Manual

9 September 2025

FAR SFT2723 Manual

9 September 2025

ActiveJet WKS-120BPJ Manual

9 September 2025

House Of Marley Classic C10 Manual

9 September 2025

House Of Marley Classic C21 Manual

9 September 2025

House Of Marley Classic C20 Manual

8 September 2025