NuTone LA225WH Manual

NuTone Dørklokke LA225WH

Læs gratis den danske manual til NuTone LA225WH (8 sider) i kategorien Dørklokke. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om NuTone LA225WH, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
MODEL LA225WH
Page 1
WESTMINSTER AND TWO-NOTE
WIRELESS CHIME
Installation & Operating Instructions
IMPORTANT: This wireless pushbutton and chime set is for
residential use, only. It will operate at an unobstructed distance
of 100 feet. Building materials may reduce operating distance.
Certain building materials; such as, but not limited to metal,
concrete, brick, stucco and foil-lined insulation; cause greater
interference than others; for example, wood or vinyl siding.
INSTALL PUSHBUTTON BATTERY
Refer to Figures 1 and 2.
1. Remove pushbutton and 3V lithium coin-battery from packaging.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its base.
3. Orient battery with “+” side viewable.
4. Insert battery into holder and press to seat.
5. Insert top of mounting base onto pushbutton and press bottom
together until mounting base snaps securely onto pushbutton.
Use only 3V (volt) lithium CR2032 style coin-battery for replacement.
INSTALL CHIME BATTERIES
Refer to Figures 3 and 4.
1. Remove chime from packaging.
2. Orient chime face-down.
3. Press on battery compartment cover serrations and slide cover in
direction of triangular-arrow.
4. Remove battery compartment cover and set aside.
5. Insert three (3) 1.5V “AA” alkaline batteries (not supplied) into battery
compartment oriented as shown on back of battery compartment.
6. Slide battery compartment cover back onto chime until it snaps
securely into place.
Figure 1
“PUSH”
TO OPEN COVER
Figure 3
3V LITHIUM
CR2032-STYLE
COIN
BATTERY
Figure 2
SLOT
Figure 4
“SLIDE”
TO OPEN
3 - “AA” SIZE BATTERIES
Figure 5
LEARN BUTTON
“LEARN” PROCEDURE
Refer to Figure 5.
1. Set wireless pushbutton and chime next to each other.
2. Press and release “Learn” button on side of chime.
3. Confirm two (2) lower-tone beeps are heard to indicate entered
“Learn” mode.
4. Press and release wireless pushbutton.
5. Confirm chime-tone is heard.
6. Repeat Step 4 to cycle through available chime-tones.
7. When desired chime-tone is heard, press and release “Learn” button
on side of chime (Note: Chime may not respond to this button being
pressed if it is too soon after chime-tone sounds).
8. Confirm two (2) higher-tone beeps are heard to indicate exited “Learn”
mode.
9. Press and release wireless pushbutton and confirm chime-tone hasn’t
changed.
• Multiple wireless pushbuttons can be used with a single chime by
selecting different chime-tones for each wireless pushbutton.
• Chime can erase all “Learned” wireless pushbuttons by pressing
and holding “Learn” button on side of chime (two initial lower-tone
beeps will sound). Release “Learn” button on side of chime after
approximately 10 seconds when four (4) higher-tone beeps are heard.
DETERMINE USABLE LOCATIONS
Do not plan to mount pushbutton directly on metal or concrete
surfaces; install a 1/8 to 1/4” wood spacer between pushbutton and
metal or concrete mounting surface.
Some stucco houses have metal mesh in the wall structure, which
will affect the wireless chime performance.
Experiment with various pushbutton and chime locations to
determine location that gives best performance before mounting
permanently.
Chime must not be located within 1-foot of any metal.
Pushbutton and chime should be located within 100-feet of each
other.
1. Place chime near its desired mounting location.
2. Select a level location and hold pushbutton in its desired mounting
location.
3. Press and release pushbutton.
4. Confirm chime-tone sounded.
5. If chime-tone does not sound, temporarily affix pushbutton to
mounting surface with double-stick or folded-over tape; repeat Steps 3
and 4.
6. If chime-tone still does not sound, move location of chime closer to
pushbutton; repeat Steps 3 and 4.
MODEL LA225WH
Page 2
Figure 6
MOUNT PUSHBUTTON
Refer to Figures 1 and 6.
1. After selecting usable locations in previous section, go to pushbutton
location.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its mounting base.
3. Make sure pushbutton mounting location is level.
4. Position pushbutton mounting base with “TOP” arrow correctly
oriented and mark base mounting holes locations.
5. Drill two (2) holes, 1/16” diameter if using supplied screws alone or
3/16” diameter if using supplied plastic anchors and screws, at base
mounting hole locations.
6. If 3/16” diameter holes were drilled, insert supplied plastic anchors.
7. Secure pushbutton base to mounting location with two (2) supplied
screws.
8. Make sure black O-ring is completely seated in its mounting base
groove with round edge at top and flat edge at bottom.
9. Hook pushbutton top catch onto top of base, swing pushbutton into
position and press bottom of pushbutton until it securely snaps onto
base.
MOUNT CHIME
Refer to Figure 7.
Chime may be used as a
portable device or wall
mounted.
1. After selecting usable locations
in previous section, go to chime
location.
2. Measure 1-7/8” down and
centered from top of chime
location and mark mounting
screw position.
3. Drill a hole, 1/16” diameter if
using supplied screw alone or
3/16” diameter if using supplied
plastic anchor and screw,
at marked mounting screw
location.
4. If 3/16” diameter hole was
drilled, insert supplied plastic
anchor.
5. Tighten screw until 1/8” remains
protruding.
6. Place chime keyhole slot over mounting screw.
7. Level chime.
TROUBLESHOOTING GUIDE
1. Chime does not sound:
a. Check battery polarity.
b. Replace batteries in chime and pushbutton.
c. Bring chime next to wireless pushbutton and test:
1. If chime sounds then change mounting location of chime.
2. If chime does not sound then conduct erase procedure per note
at end of “Learn” Procedure then conduct “Learn” Procedure,
Steps 1 through 9.
2. Chime loses volume or changes tone: Change batteries in chime.
3. Chime sounds when wireless pushbutton is not pressed:
a. Release pushbutton catch at bottom and check inside for signs of
moisture; check O-ring for cracks or damage.
b. Conduct erase procedure per note at end of “Learn” Procedure
then conduct “Learn” Procedure, Steps 1 through 9.
Figure 7
BASE
PLASTIC
ANCHORS
TOP
BLACK
“O” RING
MOUNTING
SCREWS
CHIME
1/8”
KEYHOLE
SLOT
1-7/8”
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Regulatory Information
The user is cautioned that changes or modifications not
expressly approved by the party responsible for regulatory
compliance could void the user’s authority to operate this
equipment.

Produkt Specifikationer

Mærke: NuTone
Kategori: Dørklokke
Model: LA225WH

Har du brug for hjælp?

Hvis du har brug for hjælp til NuTone LA225WH stil et spørgsmål nedenfor, og andre brugere vil svare dig


Dørklokke NuTone Manualer

NuTone

NuTone LA11BG Manual

9 Juli 2025
NuTone

NuTone LA305WL Manual

30 Marts 2025
NuTone

NuTone BK131LWH Manual

30 Marts 2025
NuTone

NuTone LA130WH Manual

30 Marts 2025
NuTone

NuTone BK144LCL Manual

30 Marts 2025
NuTone

NuTone LA223WH Manual

3 September 2024
NuTone

NuTone LA224RWH Manual

3 September 2024
NuTone

NuTone LA226WH Manual

3 September 2024
NuTone

NuTone BKL340KWH Manual

3 September 2024
NuTone

NuTone LA227WH Manual

3 September 2024

Dørklokke Manualer

Nyeste Dørklokke Manualer

Honeywell

Honeywell RCA2210N Manual

12 August 2025
Honeywell

Honeywell RPWL3045A Manual

12 August 2025
Honeywell

Honeywell RCWL3501A Manual

12 August 2025
Honeywell

Honeywell RCA2205N Manual

12 August 2025
Honeywell

Honeywell RCWL100A Manual

12 August 2025
Honeywell

Honeywell RPWL100A Manual

12 August 2025
Honeywell

Honeywell RPW101A Manual

12 August 2025
Honeywell

Honeywell RCW3505N Manual

12 August 2025
Honeywell

Honeywell RCA901N Manual

12 August 2025
Honeywell

Honeywell RCWL250A Manual

12 August 2025