NUVO Odeon 60/2873 Manual

NUVO Lys Odeon 60/2873

Læs gratis den danske manual til NUVO Odeon 60/2873 (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 12 anmeldelser. Har du et spørgsmål om NUVO Odeon 60/2873, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES

YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS

REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this fixture. Be sure to

follow the steps in the order given. Under no circumstances

should a fixture be hung on house electrical wires, nor should a

swag type fixture be installed on a ceiling which contains a

radiant type heating system. Read instructions carefully. If you

are unclear as to how to proceed, consult a qualified electrician.

NOTE: Proper wiring is essential for the safe operation of this

fixture.

FIXTURE ASSEMBLY

Carefully remove the fixture from the carton and check that all

parts are included as shown in figure. Be careful not to misplace

any of the screws or parts, which are needed to install this

fixture.

STEP 1: Place glass (L), glass (K1,K2,K3) into glass frame (N)

and secure with ball nuts (H), iron washers (I), plastic

washers (J).

INSTALLATION

IMPORTANT: Do not attach fixture directly to outlet box.

STEP 1: Drill pilot holes for wood screws (E) into the wall in

suitable location at first, insert anchors (A) into the pilot

hole. Secure back plate (D) with outlet box screws (C)

and wood screws (E).

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two

raised dimples on the circular strap. Wrap the ground

wire from the fixture (if supplied) around the green

grounding screw, then connect it to ground wire from

the outlet box (if not fixed on the outlet box) using a

wire connector (not supplied). If ground wire from the

fixture is not supplied, wrap the ground wire (if not

fixed on the outlet box) from the outlet box around the

green grounding screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your fixture.

Identify which group your fixture wire(s) falls into and

connect the wires according to the directions below:

GROUP A: Connect to Black

House Wire

GROUP B: Connect to White

House Wire

BLACK WHITE

*PARALLEL WIRE (round &

smooth)

*PARALLEL WIRE (square &

ridged)

WHITE OR GREY WITH

TRACER

WHITE OR GREY WITHOUT

TRACER

BROWN GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer

wire is square shaped or ridged and the less tracer wire is round

in shape or smooth (seen best when viewed from wire end.)

STEP 3: Take your fixture wire(s) from group A and place evenly

against the black wire from the outlet box. Do NOT

twist wires together before using wire connectors.

STEP 4: Fit a wire connector (not supplied) over the wires and

screw the connector clockwise until you feel a firmness.

STEP 5: Try gently to pull the connector off the wires. If you can

pull the connector off, carefully re-do steps 3 and 4 as

above and check again for a firm connection.

STEP 6: Connect the fixture wire from group B to the white wire

from the outlet box in the same manner. Make sure no

bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside

outlet box. Place face plate (F) allowing for mounting

screws (B) to back plate (D), and then secure it with ball

nuts (G).

STEP 2: Install light bulbs. (Please do not exceed the maximum

capacity recommended on the socket.)

STEP 3: Raise glass frame (N) over face plate (F) and secure

with screws (M).

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild

soap. Do not use abrasive materials such as scouring pads or

powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to

order replacement parts. Be sure to use exact wording from

illustration when ordering parts.

Line art shown may not exactly match the fixture enclosed.

However, the installations do apply to this fixture.

ITEM NO:60-2871, 60-2872

60-2873, 60-2874

60-2875, 60-2876

Produkt Specifikationer

Mærke:	NUVO
Kategori:	Lys
Model:	Odeon 60/2873

Har du brug for hjælp?

Hvis du har brug for hjælp til NUVO Odeon 60/2873 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys NUVO Manualer

NUVO 60/1708 Manual

18 August 2025

NUVO 62/871 Manual

18 August 2025

NUVO 62/872 Manual

17 August 2025

NUVO Bridgeview 60/1709 Manual

17 August 2025

NUVO 62/874 Manual

17 August 2025

NUVO Glamour 60/998 Manual

6 Juli 2025

NUVO 62/797 Manual

6 Juli 2025

NUVO Ballerina 60/320 Manual

5 Juli 2025

NUVO Ballerina 60/317 Manual

5 Juli 2025

NUVO 62/1763 Manual

5 Juli 2025

Lys Manualer

Nyeste Lys Manualer

Nitecore NU11 Manual

27 September 2025

Nitecore MH25 Pro Manual

27 September 2025

Nitecore NWL20 Manual

27 September 2025

Nitecore LR70 Manual

27 September 2025

Nitecore HC65 UHE Manual

27 September 2025

Nitecore MH15 Manual

27 September 2025

Globo 54802S-6 Manual

26 September 2025

LUPO DayledPro 2000 Manual

26 September 2025

DiO 54855 Manual

26 September 2025

Novy Shelf 70013 Manual

26 September 2025