Oliveri SB35BK Manual

Oliveri Køkkenvask SB35BK

Læs gratis den danske manual til Oliveri SB35BK (2 sider) i kategorien Køkkenvask. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Oliveri SB35BK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Template suits:

SB35SS

SB35GM

SB35CU

SB35BK

For topmount and undermount installation instructions see reverse.

For ﬂushmount installation refer to your installer.

Digital templates are available at oliveri.com.au

Template suits:

SB63SS

SB63GM

SB63CU

SB63BK

Template suits:

SB50SS

SB50GM

SB50CU

SB50BK Care instructions for you coloured Oliveri stainless steel sink

AVOID CONTACT WITH ROUGH OR DIRTY SURFACES as new polished stainless steel will show scratches!

• Coloured sinks should only be cleaned with soapy water and a soft cloth or sponge, then rinsed and towelled

dry.

• The colouring is a solid coating (Physical Vapour Deposit) on the surface of the stainless steel only - harsh

scratching should be avoided.

• It is highly recommended to use the wire bowl protector provided with the sink, to protect the bottom of the

bowl

• Never use steel wool in or on the sink (steel wool should be avoided with any stainless steel sink, as it can leave

steel deposits on the sink, which can cause rust).

• Never use harsh abrasive cleaning pads to clean coloured sinks.

• Never use harsh chemicals or bleaches to clean coloured sinks.

• Do not store harsh chemical (acids, chlorines, bleaches etc.) under the sink, as the vapours (even from the closed

containers) can cause rusting on the underside of the stainless steel sinks.

• Avoid prolonged contact with ordinary steel containers (e.g. tin cans), as these can rust and stain the sink.

• Avoid prolonged exposures to acids from fruit, fruit juices, salts, tea bags etc., as these may leave stains.

• Avoid leaving liquid soaps, hand sanitizing liquids etc. to dry on the surface of the sink, as these may leave stains.

Coloured Stainless Steel Care Guide

IT IS HIGHLY RECOMMENDED THAT THE ACTUAL SINK BE PRESENT AT TIME OF INSTALLATION

All cut-out templates are available online at oliveri.com.au

It is essential that the installation is waterproof and carried out in accordance with these instructions.

Tasman Sinkware will not be held responsible for any damage caused by leakage or faulty installation.

CHECK YOU HAVE THE CORRECT MODEL SINK

The model number on the sink packaging must match the model of sink

the customer ordered. Do not install if incorrect.

AVOID CUTS

The perimeter and punch-outs on the sink may contain sharp edges.

Handle the sink carefully to avoid personal injury.

CHECK THE CONDITION OF THE SINK BEFORE INSTALLATION

Do not install if defects are found – contact your retailer / point of purchase.

By installing the sink, the owner / installer accepts that the product is free

of defects – Tasman Sinkware shall not be liable for any expense incurred

relating to the removal or replacement of a defective product.

AVOID SCRATCHES

Stainless steel can be scratched if proper care is not taken during

installation.

Any advice, recommendation, information, assistance or service provided by in relation Oliveri Solutions

to goods manufactured by it or their use and installation, is given in good faith and is believed by Oliveri

Solutions to be appropriate and reliable. However, any advice, recommendation, information, assistance

or service is provided by without responsibility or liability.Oliveri Solutions

Australia (Head Office)

Oliveri Solutions Pty Ltd

ABN 12 007 551 886

PO Box 2141 Regency Park

SA 5942 Australia

P 61 8 8348 6444

F 61 8 8348 6495

E @oliveri.com.ausales

New Zealand

Fletcher Building Products Ltd

PO Box 4641 Christchurch

New Zealand 8140

P 0800 440 606

F 0800 440 532

E s @oli .com.auales veri

Stainless Steel Sink Installation Guide

Spectra Cut Out Templates

TF153 - Spectra Installation and Care Instructions.pdfd

Check Space & Level

Use a level to check the counter/benchtop – if not level, have rectiﬁed. Ensure there is adequate space

for tapware (including a splash back if speciﬁed). Check space for installation (underneath) and operation

(above). Particular care must be taken when a thick splash back is used (it may interfere with tapware

location and operation). Ensure the cabinet will not foul the sink mounting ﬂange or basins.

Template *

Template supplied in carton is for undermount installation only. For digital templates or topmount

installation templates visit oliveri.com.au.

IF COUNTER / BENCHTOP IS SUPPLIED WITH CUT-OUT, SKIP STEPS MARKED WITH*

Mark Cut Out *

Carefully mark out the template (or follow drawing instructions). Once the hole is marked out, use the

template to conduct a ﬁnal check before cutting.

IMPORTANT

For topmount sinks only, you can trace the sink itself to mark your cut out, the hole must be cut 10mm /

3/8” inside the marked line.

Cut & Finish Hole *

Re-check the position and cut out shape you have traced before cutting. Ensure there are no obstacles

below that might interfere with cutting. Drill pilot holes to accept an appropriate cutting tool for the

counter/benchtop material (wear suitable personal protection equipment).

Masking

If using a sealant, masking is necessary to prevent sealant overrun. It is recommended that the edge of

the sink and the edge of the cutout are both covered with a suitable masking tape. This tape should be

removed within 2 days of application.

Trial Fit The Sink

Check that all clips are folded in so they will adequately clear the cut-out. Carefully position the sink into

the cut-out to make sure it ﬁts correctly. If the ﬁt is not correct, remove the sink and proceed with remedial

work. Perform another trial ﬁt after corrections have been made.

Apply Sealant

Apply suitable sealant recommended for both the counter/benchtop material being used and for stainless

steel. Neutral-cure sealant will not damage stainless steel. It may be easier to apply sealant after preparing

your clamping equipment. Do not allow the sealant to dry before the sink is clamped to the counter/

benchtop.

Plumbing & Tapware

IMPORTANT - Connections to plumbing should always be done by a licensed plumber.

Fit supplied basket wastes to sink bowls. Install tapware according to manufacturer’s

instructions. Care should be taken when ﬁtting wastes to the sink. Follow the instructions

provided with the wastes.

Additional Sealant (Optional)

Apply additional sealant / caulking compound around the join where the counter/

benchtop and the stainless steel sink meet. Check that the caulking product is mildew

resistant and is suitable for use on the counter/benchtop material and also is suitable

for use on stainless steel. Clean away any excess before it dries. Note: Additional sealant

should always be used if gaps are apparent after the sink has been clamped to the

counter/benchtop

Fitting The Sink

Position and align the sink correctly in the cutout (some threaded rod and timber bearers

will help to clamp the sink in place) and either

‘A’ Sandwich Method: RECOMMENDED FOR BOTH THIN AND THICK COUNTER/

BENCHTOP. Firmly ﬁx a support board into / over the cabinet and cut the sink hole so

that the sink ﬂange will sit above the edge of the board. Slightly rout the edge so that

the sink ﬂange will sit ﬂush with the top surface. Test for ﬁt. Install sink and seal between

ﬂange and support board. Apply sealant to the underside edge of the cutout on counter/

benchtop material and position it over the support board to sandwich the sink in place.

Fasten the counter/benchtop securely.

‘B‘ Bond: For minimum 1” / 25mm thick material. Bond it to the underside of the

counter/benchtop with a structural high strength epoxy compound. NOT RECOMMENDED

TO BE USED WHEN FITTING SINK TO THINNER COUNTER/BENCHTOPS.

‘C‘ Bolt: For minimum 1” / 25mm thick material. Bolt it to the counter /benchtop

using “molly” assemblies. Care must be taken during drilling and tightening to avoid

cracking. NOT RECOMMENDED TO BE USED WHEN FITTING SINK TO THINNER COUNTER/

BENCHTOPS.

If you have any doubts, conﬁrm the correct mounting method for your material by

consulting the counter/benchtop supplier.

Above shows sandwich method

where sink is clamped between a

lower support board (with routed

edge) and the upper counter /

benchtop using method A.

Above shows how threaded rod

and timber bearers may be used

to clamp the sink in place while

fastening to the counter / benchtop

using methods B and C.

Do not overtighten as this may

damage the sink.

Counter / benchtop

Sealant

Sink flange

Support board with routed edge

(such as timber)

Counter / benchtop

Sealant

Sink flange

Epoxy

1” Counter / benchtop with hole drilled

Molly

Sealant

Sink flange

Saddle

Screw

UNDERMOUNT ONLY

Fitting The Sink

Position and align the sink correctly in the cutout and lower it onto the counter/benchtop.

From underneath, install and tighten the clips with a screwdriver using a suitable

tightening sequence (tighten from the centre of the sink to the outer edge) until the sink

is secure and no gaps are visible. Take extra care if using power tools as over-tightening

can damage clips. The clips included with the sink require a minimum counter/benchtop

thickness of 1” / 25mm. If ﬁtting into a thinner bench top, timber blocks or similar should

be installed between the bench top and the clip.

TOPMOUNT ONLY

Stainless Steel Sink Installation Guide

TF153 - Spectra Installation and Care Instructions.pdfd

Produkt Specifikationer

Mærke:	Oliveri
Kategori:	Køkkenvask
Model:	SB35BK

Har du brug for hjælp?

Hvis du har brug for hjælp til Oliveri SB35BK stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Køkkenvask Oliveri Manualer

Oliveri EE02 Manual

21 Maj 2024

Oliveri AP1411 Manual

18 Maj 2024

Oliveri SB35BK Manual

16 Maj 2024

Køkkenvask Manualer

Nyeste Køkkenvask Manualer

Caple AXL50 Manual

2 Oktober 2025

Caple MODE025 Manual

30 September 2025

Caple MODE034 Manual

30 September 2025

Caple MODE3434 Manual

30 September 2025

29 September 2025

29 September 2025

29 September 2025

29 September 2025

Caple FORM150R Manual

29 September 2025

Caple Di45 Manual

29 September 2025