Optex AX-350DH MK3 Manual

Optex Ikke kategoriseret AX-350DH MK3

Læs gratis den danske manual til Optex AX-350DH MK3 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Optex AX-350DH MK3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

AX-350DH MK III

AX-650DH MK III

AX-350DH TS

AX-350DH BT

No.59-1073-0 0406-04

FEATURES

CONTENTS

·Multiple beam installation of up to 4 sets

·Simple optical alignment

·High waterproofing property; jet-proof : IP65

·Wide optical alignment range:

±90 degrees horizontally; ±20degrees vertically

*AX-350DH BT:

±60 degrees horizontally; ±45 degrees vertically

·Reduced possibility of false alarms caused by flying

objects

1. INSTALLATION GOOD PRACTICE

2. PARTS IDENTIFICATION

3. NOTES ON INSTALLATION

4. INSTALLATION METHOD

5. TERMINAL CONNECTIONS

6. WIRING

7. OPTICAL ALIGNMENT

8. BEAM INTERRUPTION TIME ADJUSTMENT

9. RE-TRANSMISSION FUNCTION

10. WALK TEST

11. HEATER UNIT HU-2

12. BACK COVER BC-1

13. DIMENSIONS

14. TROUBLESHOOTING

15. SPECIFICATIONS

-1-

INSTALLATION

INSTRUCTIONS

top/bottom unit AND/OR selectable

maximum detection range: 350ft.(100m)

PHOTOELECTRIC DETECTOR

·Digital communication function

·Cross talk prevention function

·Peak Finder Interface (P.F.I ) of Dual Alignment

Level Indicator

·Mode-specific indicator allowing simple and

accurate optical alignment

·Simple beam alignment without the “Beam

Blocking Tool”

·Minimization of light disturbance

·ATPC ( Auto Transmit Power Control )

to optimize the power of beam

Thank you for purchasing our product.Be sure to read the

following installation instructions carefully before beginning

installation.Make sure that the person in charge of system

management stores this manual carefully for maintenance

and management.

model for beam tower, upper and lower unit unit AND/OR selectable

maximum detection range: 350ft.(100m)

maximum detection range: 650ft.(200m)

Downloaded from manuals search enginewww.Manualslib.com

-3-

28-39inch(0.7-1m)

23.5 inch(60cm)

39 inch(1m)

2. PARTS IDENTIFICATION

Mounting Plate

Wall Mounting Screw

Holes & Waterproof

Plug (x 4)

Vertical Alignment Dial

Terminals

See 5. “TERMINAL” on PAGE6.

Horizontal Alignment Dial

View Finder

Cover Lock Screw

Cover

Unit Base

Mounting Screw

(x 4)

Wiring Hole (x 2)

Monitor Jack

Alignment Level Indicator

Unit Base Pole Mounting

Screw Holes &

W a t e r p r o o f

Plug (x 4)

Rubber

Bushing

Rubber Bush Slot

Pole Mounting

Screw Holes &

Waterproof Plug

(x 4)

Hood

Switch Section

Transmitter

Receiver

Clears the registered address (see 14. “TROUBLESHOOTING” on Page15).

Indicates the registered address by the flickering of the six indicator LEDs for about 10

seconds (see 14. “TROUBLESHOOTING” on Page15).

Switches between high and low the level of infrared beam reception output to the monitor

jack.

Use this switch for multi-level installation (see 7-2. “Master/slave selector switch setting” on

Page8).

Switches the interruption time between the four settings (see 8. “BEAM INTERRUPTION TIME

ADJUSTMENT” on Page11).

This switches the detection time for the top unit when AX-350DH TS / BT in the OR mode.

Switch to the AND mode for detection of simultaneous interruption for the top and the bottom

units and to the OR mode for detection of interruption for either unit (see 7-3. “AND/OR

selector switch setting” on Page8).

Turning the switch to ON in the OR mode fixes the interruption time for the bottom unit to one

second (see 8. “BEAM INTERRUPTION TIME ADJUSTMENT” on Page11).

ADDRESS CLEAR:

ADDRESS CHECK:

MONITOR JACK switch:

MASTER/SLAVE switch:

INTERRUPTION TIME switch:

AND/OR switch:

(AX-350DH TS / BT only)

Resets the registered address to the factory settings

(see 14. “TROUBLESHOOTING” on Page15).

Indicates the registered address by the flickering of the six indicator LEDs for about 10 seconds

(see 14. “TROUBLESHOOTING” on Page15).

Switches between high and low the level of infrared beam reception output to the monitor jack.

Use this switch for multiple beam installation (see 7-2. “Master/slave selector switch setting” on Page8).

When more than one detector with the same address is on the alarm line, switches one of them

to prevent malfunction caused by cross talk (see 14. “TROUBLESHOOTING” on Page15).

Switch to the AND mode for detection of simultaneous interruption for the top and the bottom

units and to the OR mode for detection of interruption for either unit (see 7-3. “AND/OR selector

switch setting” on Page8).

ADDRESS CLEAR:

ADDRESS CHECK:

MONITOR JACK switch:

MASTER/SLAVE switch:

FORCED ADDRESS switch:

AND/OR switch:

(AX-350DH TS / BT only)

BOTTOM UNIT INTERRUPTION TIME switch:

(AX-350DH TS / BT only)

3. NOTES ON INSTALLATION

[2] Alignment angle[1] Detection range and installation height [3] Pole mounting

·Pole size should be diameter

1.9inch(48mm).

·The length of the wiring cable out of

the pole should be within 23.5

inch(60cm).

Without AX-350DH BT

180 degrees (± 90 degrees) 40 degrees (± 20 degrees)

AX-350DH BT

120 degrees (± 60 degrees) 90 degrees (± 45 degrees)

distances between the Receiver and

the Transmitter are listed below:

Horizontally Vertically

35-350ft.(10-100m) : AX-350DH MK III, AX-350DH TS,

AX-350DH BT

65-650ft. (20-200m) : AX-650DH MK III

Normally, the installation height should

be 0.7 – 1.0m. When OR mode is used,

the installation height of lower beam

should be 15cm from the ground.

For best performance, avoid aligning

detectors at 45 degree angles except

AX-350DH BT.

Note

Downloaded from manuals search enginewww.Manualslib.com

Produkt Specifikationer

Mærke:	Optex
Kategori:	Ikke kategoriseret
Model:	AX-350DH MK3

Har du brug for hjælp?

Hvis du har brug for hjælp til Optex AX-350DH MK3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Optex Manualer

Optex OVS-50TNR Manual

28 September 2025

Optex InSight INS-HX-80N Manual

10 August 2025

Optex AX-100TF Manual

23 Juli 2025

Optex CX-702RS Manual

19 Juni 2025

Optex RLS-PB2 Manual

26 Januar 2025

Optex QXI-DT-X5 Manual

14 December 2024

Optex WXI-R Manual

5 December 2024

Optex VXS-AM Manual

5 December 2024

Optex SIP-5030-IP-BOX Manual

5 December 2024

Optex AX-100TFR Manual

5 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Icy Box IB-MS404-T Manual

17 Oktober 2025

LC-Power Platinum Pro LC1000P2 V3.1 Manual

17 Oktober 2025

Hagor 3215 Manual

17 Oktober 2025

Menuett 005-908 Manual

17 Oktober 2025

FBT MPU 4060 Manual

17 Oktober 2025

Metz 130E405032-E Manual

17 Oktober 2025

Hagor 3210 Manual

17 Oktober 2025

Lucide Concri 05910/10/36 Manual

17 Oktober 2025

Hagor 3232 Manual

17 Oktober 2025

IFi Audio GO blu Air Manual

17 Oktober 2025