Optex REDWALL SIP-100-IP-BOX Manual

Optex Ikke kategoriseret REDWALL SIP-100-IP-BOX

Læs gratis den danske manual til Optex REDWALL SIP-100-IP-BOX (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Optex REDWALL SIP-100-IP-BOX, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

PoE IP Encoder

PIE-1

PoE IP Encoder

PIE-1

INSTALLATION INSTRUCTIONS

( for SIP series and RLS series )

No.5919420

▪ PIE-1 changes analog relay output signals (N.C.) to

original ASCII code.

▪ PIE-1 can supply power to detector using a PoE hub

or switch.

▪ Follow all cautions and instructions in this manual

before installation.

▪ Keep this manual after installation so that you can

read when necessary.

▪ Remember the meanings of “Warning” and

“Caution” below to use the product safely.

If you ignore a caution, the user or other

people may be injured or the product or

something around it may be damaged.

If you ignore a warning, the user or other

people may be injured or dead.

▪ Do not repair, dismantle or modify the product

yourself.

▪ Do not touch the product with a wet hand.

▪ Be careful not to damage other interior wiring when

installing or wiring the product.

▪ Power off the product immediately if smoke, odor or

strange sound emits from the product.

▪ Do not install the product in an extremely moist place

such as a bathroom or a place where the product

may be wet.

▪ Insert the connectors securely when wiring.

Caution

■No. 6-32 UNC screw (5/8 inch), 6 pcs

■Alarm 10-pin cable (26cm)

■Power 2-pin cable (26cm)

■Alarm 6-pin cable (10cm)

■Alarm 4-pin cable (10cm)

■Power 2-pin cable (10cm)

■Main unit of PIE-1

SAFETY PRECAUTION

FEATURES

Connectors

WarningWarning

Warning: This is a class A product. In a domestic

environment this product may cause radio interference

in which case the user may be required to take

adequate measures. (EN55022)

CE Statement

Warning

Caution

■SIP mounting plate

for Gang Box

■ Gasket sheet

for Gang Box

PARTS IDENTIFICATION

Ethernet connector for PoE

Ethernet connector for detector

24VDC Power output connector

12VDC Power output connector

Alarm input connector

▪

Be sure to use the attached cables.

▪

Do not use 12V and 24V power sources at the same time.

Caution

(1) Prepare an appropriate Dual Gang Box.

(2) Using an Allen key, detach the SIP base from the SIP main unit.

(1) Plug the alarm 10-pin cable to

PIE-1.

(2) Plug the power 2-pin cable to

PIE-1. Use the 12VDC connector.

Note: When using an optional heating

unit, use the 24VDC connector.

(3) Set the Selector switch of PIE-1

to the left.

(4) Plug a CAT5 cable to the

Ethernet connector for PoE.

(5) Place the PIE-1 into the Dual

Gang Box.

(1) Take off a rectangular gasket

and two round gasket from the

gasket sheet.

(2) Apply the rectangular gasket on

the SIP mounting plate.

(3) Apply the two round gaskets in

layers around the round hole of

the SIP mounting plate.

(1) Pass the alarm 10-pin

cable and the power

2-pin cable through

the hole.

(2) Using four screws,

mount the SIP

mounting plate to the

Gang Box.

(3) Pass the cables

through the hole on

the back of the SIP

base.

(4) Using two screws,

mount the SIP base to

the SIP mounting plate

on the Gang Box.

Step 1

Step 3Step 2 Step 4

Step 6Step 5 Step 7

Mount the SIP

main unit onto

the SIP base.

(1) Connect the power and alarm

cables.

(2) If cables are too long, put the

extra portions into the Gang Box.

When the PIE-1 unit is accommodated not in Gang box, mount it in weather proof box or cabinet to avoid moisture.

Plug the alarm 6-pin cable, the

alarm 4-pin cable and the power

2-pin cable to terminals on the SIP

base.

 CONNECT PIE-1 TO THE SIP MAIN UNIT

Warning

Note: Refer to the

Connection

Table.

Step 3

Step 4

Step 5

Step 6

Step 2

(1) (2)

(3)

(4)

Do not use

Produkt Specifikationer

Mærke:	Optex
Kategori:	Ikke kategoriseret
Model:	REDWALL SIP-100-IP-BOX

Har du brug for hjælp?

Hvis du har brug for hjælp til Optex REDWALL SIP-100-IP-BOX stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Optex Manualer

Optex InSight INS-HX-80N Manual

10 August 2025

Optex AX-100TF Manual

23 Juli 2025

Optex CX-702RS Manual

19 Juni 2025

Optex RLS-PB2 Manual

26 Januar 2025

Optex QXI-DT-X5 Manual

14 December 2024

Optex WXI-R Manual

5 December 2024

Optex VXS-AM Manual

5 December 2024

Optex SIP-5030-IP-BOX Manual

5 December 2024

Optex AX-100TFR Manual

5 December 2024

Optex FTN-AM Manual

5 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Aqua-Vu Micro Stealth 4.3 Manual

20 August 2025

OnTruss EventBoard C90I BASIC Manual

20 August 2025

Tefal Quickchef HB672B Manual

20 August 2025

Gravity XW GLOVE Manual

20 August 2025

Roland V-4CF Manual

20 August 2025

Tefal Uno M FF133D Manual

20 August 2025

LD Systems MAUI 5 GO 100 BC W Manual

20 August 2025

Moulinex Bake Partner QA523B Manual

19 August 2025

Uniprodo UNICLEAN 142B Manual

19 August 2025

Tefal Body Partner LL9503 Manual

19 August 2025