Optex SIP-100 Manual

Optex Bevægelsesdetektor SIP-100

Læs gratis den danske manual til Optex SIP-100 (12 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Optex SIP-100, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/12
- 1 -
ENGLISH FRANÇAIS DEUTSCH ITALIANO ESPAÑOL
2.3-4.0 m
(7.6-13 ft.)
F
6 4 2 5 3 1
F 6 F 4 F 2 F 5 F 3 F 1
E 6 E 4 E 2 E 5 E 3 E 1
D 6 D 4 D 2 D 5 D 3 D 1
C 6 C 4 C 2 C 5 C 3 C 1
B 6 B 4 B 2 B 5 B 3 B 1
E
D
C
B
Area Masking Seals
3020 (
1 2
3
4 5 6 7
B1
C1
D1
E1
F1 F6
2F 3F 4F 5F
E5E2 E3 E4
D5D2
C5C2 C3 C4
B5B2 B4
3D 4D
B3
E6
D6
C6
B6
Area View Finder
INSTALLATION AND MAINTENANCE NOTES
Warning
Failure to follow the instructions provided
with this indication and improper handling
may cause death or serious injury.
Caution
Failure to follow the instructions provided
with this indication and improper handling
may cause injury and/or property damage.
The check mark indicates recommendation.
The nix sign indicates prohibition.
Warning Caution
Never repair or
modify product
Hold the main unit
securely when you
install or service it.
If you remove your
hands from the main
unit when cables are
connected to it, the
main unit may fall
and the connector
cables may break
or the circuit board
may be damaged.
Caution
Verify that the
power is off before
connecting the
wiring.
2
PARTS IDENTIFICATION
1
No. 59-1545-7 1710-11
No. 59-1545-7 1710-11
INSTALLATION INSTRUCTIONS
Synthesized Intelligent PIR
REDWALL-V series
FEATURES
* Intelligent PIR Detection System
- tectDe io am em ur an illumi an or omn of bient t perat e d n ce f aut atic
sensitivity management
- Advanced detection algorithm
- uble Dual/One Quad py ments with patented Double Do ro-ele
Conductive Shielding for main area SIP-5030
- Double Quad pyro-elements with patented Double Conductive
Shielding for main area SIP-100
* Built-in creep zone detector (Double dual pyro-elements)
* Anti-vandalism functions
- Anti-rotation function with accelerometer
- Anti-masking function with photo-beam
- Reinforced polycarbonate housing
- Max. 4 m (13 ft.) installation height
* Independent sensitivity selector for creep/near/far areas
* Independent N.C. and N.O. output for main area SIP-5030
* 2 x N.C. and N.O. independent output for main areas (Near and
Far areas ) SIP-100
* Adjustable alarm interval time
REDWALL-V
: Synthesized Intelligent PIR with creep zone
SIP-5030
SIP-100
•
•
*1: Not used for the SIP-100.
2-1
INSTALLATION HINTS
The detection zones of all-V, which may be cause of false Redw
alarms can be eliminated by masking.
1. To confirm detection zones
Use optional Area View Finder, AVF-1
2. To eliminate unnecessary detection zones
a. Use supplied area masking seals.
b. Use equiped area masking plates.
The following shows an example;
Detection zones and related segments of the mirror of SIP-3020.
See step 4-1 and 6.
FAR
NEAR
7
65
43
2
1
B6
C6
D6
E6
B3
C3
D3
E3
F3
B2
C2
D2
E2
F2
B1
C1
D1
E1
F1
B4
C4
D4
E4
F4
B5
C5
D5
E5
F6
F5
Mount the detector so that the majority of
traffic flow is across the detection pattern.
Base
Fixing screw
for the base Main unit
Masking plate for
near area (*1)
Fixing rubber
form (*1)
Window
Fixing screw
for the cover
Cover
Far area mirror
Adjustment screws
(two facing each other)
Angle adjustment guide
Near area mirror
Arrow marking
Fixing screw
Nylon wire
loop
When servicing, the sensor
can be hooked onto the base
using the nylon wire loop.
Creep unit
Synthesized Intelligent PIR
REDWALL-V series
REDWALL-V SIP-3020
UL
* UL/c-UL Listed
* UL-1: P 0 P-100 e rec d no to be c ected to an m itiat gSI -503 / SI ar ommende t onn alar in in
circuit but may be c ected to a tonn roubl alare m circuit if isance t s e no t e. nu rip ar t olerabl
* SIP-100 does not have a masking
function.
* Creep
zones can
not be
masked.
- 2 -
3-1
Wall Mounting
Attach the paper template (an accessory) onto the wall,
and drill a 6-mm dia. mounting hole and a cabling hole.
Insert the anchor bolt (an accessory) into the board mount
hole.
Using an allen key, remove the main unit from the base.
Drill through the bushing of the wiring hole, pass the cable
through the hole, and secure the base to the wall.
Connect the cable to the terminal block (see Step 3-3).
Mount the main unit onto the base.
Cautions>>
When mounting the main unit, take care not to trap the
nylon wire loop. Also, take care not to get your fingers
caught.
Check to see that the various settings and operations are
correct.
Caution>>
When the red LED flashes after the power turns on,
this signifies that the system is warming up Wait for .
approximately 60 seconds.
INSTALLATION AND ANGLE ADJUSTMENT
3
(1)
(2)
(3)
(4)
(5)
(6)
3-2
Inside View of the Base
3-3
WIRING
*1: TAMPER terminals to be connected to a 24 hour supervisory loop.
*2: FAR AREA ALARM OUTPUT, when the NUMBER OF OUTPUTS select switch is
ON(3) (see Step 5-3).
*3: Both FAR AREA and NEAR AREA ALARM OUTPUT, when the NUMBER OF
OUTPUTS select switch is OFF(2).
And Only NEAR AREA ALARM OUTPUT, when the NUMBER OF OUTPUTS
select switch is ON(3) (see Step 5-3).
TROUBLE
OUTPUT
Trouble out is used for anti-masking signal. When
an object is placed close to the lens surface, for
a period of more than 100 seconds (approx.), the
IR anti-masking circuit will activate and generate a
trouble signal.
TAMPER
OUTPUT
It is detected when the cover is opened.
It is detected when the main unit is removed from
its base.
Anti-Rotation:
Damage sustained by the main unit is detected.
If the main unit is impacted in a horizontal or
vertical direction and if the position of the main
unit has changed, damage sustained by the main
unit will be detected.
Waterproof seal
(Do not remove
this seal.)
Base
Bushing of wiring
hole ( 18)Φ
Open wiring cap
Main unit connector
Wall mounting hole
Wiring terminals
(SIP-100 ONLY)
Wall mounting hole
Bushing of wiring
hole ( 18)Φ
Wiring terminals
1 Loosen the
fixing screw
for the
base.
2 Open.
3 Unplug
the cable
connector.
4 Pull out.
POWER INPUT
TAMPER OUTPUT *1
FAR AREA AND NEAR AREA *3
ALARM OUTPUT (N.C.)
ALARM OUTPUT (N.O.)
TROUBLE
OUTPUT
SPARE
4 Tighten and secure
the fixing screw for
the base.
2 Connect the
connector.
3 Close.
1 Insert and
secure here.
Nylon
wire
loop
Distance from the ground to
the bottom of the template
must be between 2.3 m (7.6 ft.)
and 4 m (13 ft.).
CREEP
ALARM OUTPUT
(N.C.)
ALARM OUTPUT
(N.O.)
FAR AREA *2
ALARM OUTPUT (N.C.)
ALARM OUTPUT (N.O.)
(SIP-100 only)
Wiring hole (M20 x 1.5) Unit:mm
* UL-2: All relay outputs of Alarm/Trouble are resistive load only.
* UL-3: UL requires that the detector is to be connected to a UL listed Burglar power
supply Class 2, capable of providing a input range of not greater than 11 VDC - 26
VDC, 50 mA and battery standby time of 4 hours.
* UL-4: The equipment shall be installed in accordance with the National Electrica
Code, NFPA 70.l
Name Function

Produkt Specifikationer

Mærke: Optex
Kategori: Bevægelsesdetektor
Model: SIP-100

Har du brug for hjælp?

Hvis du har brug for hjælp til Optex SIP-100 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Bevægelsesdetektor Optex Manualer

Optex

Optex WXS-AM Manual

15 Januar 2025
Optex

Optex FLX-S Manual

17 December 2024
Optex

Optex SIP-100 Manual

16 December 2024
Optex

Optex SL-350QDM Manual

16 December 2024
Optex

Optex SIP-3020WF Manual

16 December 2024
Optex

Optex FLX-P Manual

16 December 2024
Optex

Optex FLX-A Manual

16 December 2024
Optex

Optex RLS-2020S Manual

5 December 2024
Optex

Optex BXS-R Manual

5 December 2024
Optex

Optex HX-80N Manual

5 December 2024

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

ORNO

ORNO OR-CR-289 Manual

15 Juni 2025
ORNO

ORNO OR-CR-279 Manual

15 Juni 2025
ORNO

ORNO OR-CR-273 Manual

15 Juni 2025
ORNO

ORNO OR-CR-283 Manual

14 Juni 2025
ORNO

ORNO OR-CR-277 Manual

14 Juni 2025
ORNO

ORNO OR-CR-271 Manual

14 Juni 2025
Theben

Theben PIRA TO AP Manual

8 April 2025
Esylux

Esylux PD-C 360i/24 DUOplus-FM Manual

31 Marts 2025
Satel

Satel SLIM-PIR-PET Manual

20 Marts 2025
Crestron

Crestron GLA-LDL-PC-0-10 Manual

8 Januar 2025