Optex SIP-3020WF Manual

Optex Bevægelsesdetektor SIP-3020WF

Læs gratis den danske manual til Optex SIP-3020WF (12 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Optex SIP-3020WF, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

EN-1

2.3-4.0 m

(7.6-13 ft.)

INSTALLATION AND MAINTENANCE NOTES

Warning Caution

Never repair or

modify product

Hold the main unit

securely when you

install or service it.

If you remove your

hands from the main

unit when cables are

connected to it, the

main unit may fall

and the connector

cables may break

or the circuit board

may be damaged.

Caution

Verify that the

power is off before

connecting the

wiring.

PARTS IDENTIFICATION

59-3462-0 2310-11

INSTALLATION INSTRUCTIONS

Synthesized Intelligent PIR

REDWALL-V series

Synthesized Intelligent PIR

REDWALL-V series

FEATURES

,CDV9-3( noitpmusnoc rewop woL * 40μA (standby) 5mA max.)

* Low battery signal

* Intelligent PIR Detection System

- Three dual pyro-elements with patented Double Conductive

Shielding

- Detection of ambient temperature and illuminance for

automatic sensitivity management

- Advanced detection algorithm

* Anti-vandalism functions

- Max.4 m (13 ft.) installation height

- Anti-rotation function with accelerometer

- Anti-masking function with photo-beam

* Independent sensitivity selector for near/far areas

* Detection logic selector

* Detection range selector

* Independent N.C. and N.O. ALARM output

* Adjustable alarm interval time

* Reinforced polycarbonate housing

REDWALL-V

: Low current Synthesized Intelligent PIR

SIP-3020WF

SIP-4010WF

SIP-404WF

•

Mount the detector so that the majority of is across the detection pattern.trafﬁc ﬂow

dna FW0104-PIS eht rof desu toN :1*

SIP-404WF.

2-1

INSTALLATION HINTS

Base

Fixing screw

for the base

Main unit

Masking plate for near

area (*1)

Fixing rubber

form (*1)

Window

Fixing screw

for the cover

Cover

Far area mirror

Masking plate for far area

Fixing rubber form

Adjustment screws

(two facing each other)

Angle adjustment guide

Near area mirror

Arrow marking

Fixing screw

Nylon wire

loop

When servicing, the sensor

can be hooked onto the

base using the nylon wire

loop.

*UL-1: When assessing the installation and application, alarms triggered

by conditions such as weather, blowing leaves and bush, or related

environmental conditions, etc., need to be considered.

It is recommended that the intrusion detection unit is not to be

connected to an alarm initiating circuit but may be connected to

a trouble alarm circuit if nuisance trips are not tolerable.

EN-2

3-1

Wall Mounting

Attach the paper template (an accessory) onto the wall,

and drill a 6-mm dia. mounting hole and a cabling hole.

Insert the anchor bolt (an accessory) into the board mount

hole.

Using an allen key, remove the main unit from the base.

Drill through the bushing of the wiring hole, pass the cable

through the hole, and secure the base to the wall.

Connect the cable to the terminal block (see Step 3-3).

Mount the main unit onto the base.

Cautions>>

When mounting the main unit, take care not to trap the

nylon wire loop. Also, take care not to get your fingers

caught.

Check to see that the various settings and operations are

correct.

Caution>>

When the red LED flashes after the power turns on,

this signifies that the system is warming up. Wait for

approximately 120 seconds.

INSTALLATION AND ANGLE ADJUSTMENT

(1)

(2)

(3)

(4)

(5)

(6)

3-2

Inside View of the Base

3-3

WIRING

Cautions>>

Maximum wiring length is 3 m.

Name Function

TROUBLE

OUTPUT

Trouble out is used for anti-masking signal and

low battery signal. When an object is placed close

to the lens surface, for a period of more than

120 seconds (approx.), the IR anti-masking circuit

will activate and generate a trouble signal.

When the battery power is less than 2.3V DC, and

this condition continues more than 2.5 hours, the

signal will be generated.

TAMPER

OUTPUT

It is detected when the cover is opened.

It is detected when the main unit is removed from

its base.

Anti-Rotation:

Damage sustained by the main unit is detected.

If the main unit is impacted in a horizontal or

vertical direction and if the position of the main

unit has changed, damage sustained by the main

unit will be detected.

Waterproof seal

(Do not remove

this seal.)

Base

Bushing of wiring

hole

Open wiring cap

Main unit connector

Wall mounting hole

Bushing of wiring

hole

Wiring terminals

① Loosen the

ﬁxing screw

for the

base.

② Open.

③ Unplug

the cable

connector.

④ Pull out.

POWER INPUT

TAMPER OUTPUT *1

ALARM OUTPUT (N.C.)

ALARM OUTPUT (N.O.)

TROUBLE

OUTPUT

SPARE

④ Tighten and

secure the

ﬁxing screw

for the base.

② Connect the

connector.

③ Close.

① Insert and

secure here.

Nylon

wire

loop

Distance from the ground to

the bottom of the template

must be between 2.3 m (7.6 ft.)

and 4 m (13 ft.).

* The Cable Gland (accessory )

enables wiring.

*1: TAMPER terminals to be connected to a 24 hour supervisory loop.

(*UL-3)

*UL-3: UL/ULC required the unit to be connected to a UL/ULC Listed

control panel or a power limited Listed Burglar alarm power supply

capable of providing a minimum of 4 hours of battery standby power

for UL/ULC Listed application.

*UL-2: Minimum wire gauge is 22 AWG.

Wiring methods shall be accordance with the National Electrical Code

NFPA 70 or CSA 22.2, Part 1 of the Electrical code for Canada.

Produkt Specifikationer

Mærke:	Optex
Kategori:	Bevægelsesdetektor
Model:	SIP-3020WF

Har du brug for hjælp?

Hvis du har brug for hjælp til Optex SIP-3020WF stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Optex Manualer

Optex AX-200TF Manual

10 August 2025

Optex RLS-50100V Manual

19 Februar 2025

Optex WXS-AM Manual

15 Januar 2025

Optex FLX-S Manual

17 December 2024

Optex SIP-100 Manual

16 December 2024

Optex SL-350QDM Manual

16 December 2024

Optex SIP-3020WF Manual

16 December 2024

Optex FLX-P Manual

16 December 2024

Optex FLX-A Manual

16 December 2024

Optex RLS-2020S Manual

5 December 2024

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

10 August 2025

10 August 2025

9 August 2025

9 August 2025

9 August 2025

9 August 2025

Vemer Muvy DUO Manual

4 August 2025

Theben thePassa P360 KNX UP Manual

3 August 2025

Theben theRonda P360 DALI-2 HCL UP Manual

3 August 2025

Theben thePiccola S360-100 DE Manual

3 August 2025