Ozito CPP-802 Manual

Ozito Pomp CPP-802

Læs gratis den danske manual til Ozito CPP-802 (8 sider) i kategorien Pomp. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Ozito CPP-802, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
7. Recommended Setup
Cleaning
Use a moist cloth to wipe down the pump housing. Allow to dry
thoroughly before storing in a dry location that is protected from bad
weather conditions.
Storage
If there is danger of frost, dismantle the device and accessories, clean
and store them in a place protected from frost.
Dismantle and store
1. Disconnect the device from the mains
supply.
2. Fully open any shut-off mechanisms
(spray nozzles, valves, etc.) in the
pressure line so that the air can escape
without obstruction.
3. Completely empty the pump by
unscrewing the water drain plug.
4. Dismantle the suction and pressure lines
from the device.
5. Store device in a frost-free room
(at least 5 °C).
WARNING! MAKE SURE THE PUMP IS DISCONNECTED
FROM ELECTRIC POWER SUPPLY BEFORE
PERFORMING MAINTENANCE PROCEDURES.
WARNING! THE INPUT HOSE OR PIPE SHOULD BE
LOW ENOUGH IN THE WATER TO ENSURE THAT IF
THE WATER LEVEL FALLS, THE PUMP WILL NOT RUN DRY.
ENSURE THAT THIS IS CHECKED WHEN IN OPERATION.
WARNING! MAKE SURE THAT THE DEVICE AND
CONNECTED ACCESSORIES ARE DEPRESSURIZED
BEFORE CARRYING OUT ANY WORK ON THE DEVICE.
Positioning the hose or pipe
Position the input hose or pipe so that it rises from the water drawing
source to the pump. Where possible, avoid positioning the input hose
or pipe higher than the pump, as this would delay the escape of air
bubbles from the input hose or pipe and impede the priming process
(see section ‘ ’ for description on priming the pump)Priming the pump
• Thesuctionlineshouldbeasshortaspossible,sincetheconveying
capacity decreases as the length of the line increases.
Note: A leaking hose or pipe will draw in air and therefore not draw in
any water.
Note: A non-return valve is recommended so that the water does not
run off when the pump is shut off.
Note:Asuctionin-linelterwitha3000l/hourminowrate,and150to
250micronmeshmustbeusedtoprotectthepumpfromsand,dirtetc.
TheOzitoPAPF-001Pre-lterorequivalentisavailablefromBunnings
stores.
Note: During the initial set-up, please purge all air from the system via
the discharge outlet highest in the system.
INSTALLATION
Recommended set-up
Connection with tank base below water pump
Connection with tank base level with water pump
Connection with tank base above water pump
F EIRM BAS
SOLID STRUCTURE
0
1
2
3
4
5
6Bar
WATERTANK
NON-RETURN
VALVE
DISCHARGE
OUTLET
GATE
VALVE
SUCTION LINE
150mm 150mm
UNION
COUPLING
depending on
installation
IN-LINE
FILTER
WATERTANK
GATE
VALVE
SUCTION LINE
150mm
F EIRM BAS
SOLID STRUCTURE
0
1
2
3
4
5
6Bar
DISCHARGE
OUTLET
150mm
UNION
COUPLING
depending on
installation
IN-LINE
FILTER
0
1
2
3
4
5
6Bar
150mm 150mm
WATERTANK
GATE
VALVE
SUCTION LINE
SOLID STRUCTURE
DISCHARGE
OUTLET
F EIRM BAS
UNION
COUPLING
depending on
installation
IN-LINE
FILTER
WARNING! TO ENSURE CORRECT PUMP OPERATION
IT IS ESSENTIAL THAT A SUCTION IN-LINE FILTER BE
USED FOR A CLEAN WATER SUPPLY.
MAINTENANCE
DESCRIPTION OF SYMBOLS CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recyclingpackagingreducestheneedforlandllandrawmaterials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: enquires@ozito.com.au
SPARE PARTS
TROUBLESHOOTING
Problem LED Display Possible Cause Solution
Thepumpoperates
but water is not
owing
Yellow, green and red
LEDs are on
Thereisairinthepumphead Disconnectfrompowersupply,opentheprimingscrewandllthe
pump head with water
VerifythejointsaresealedtightlywithTeontape
Thesuctionpipeisblocked Disconnect from power supply, clean the suction pipe
Thepumpisnotprimed Followinginstructions“PrimingThePump”
Thein-linelterisblocked Cleanthelter
Theinletandoutletarenot
connected with the pipe or hose
correctly
Connect the inlet and outlet with pipe or hose correctly, ensure
thereisnoleakage.UseTeontapeonallconnections.
Nowaterowfromsupply Checkifthesupplysourcehassufcientwater
Thepumpwon’tstart No LEDs on Power not switched on If the yellow light doesn’t illuminate, check the mains supply
Yellow LED on Onbuttonhasnotbeenpressed Onceconnectedwiththemainspower,theyellowlightwill
illuminate.Whenthisoccurs,presstheOnbutton.
Pumps stops No LEDs on Check the mains powerThemainspowerisdisconnected
Power failure When power is restored, the yellow light will illuminate, press the
Onbutton
Yellow and red LEDs
are on
Thereisairinthepumphead Disconnectfrompowersupply,opentheprimingscrewandllthe
pump head with water
VerifyalljointsaresealedtightlywithTeontape
Thesuctionpipeisblocked Disconnect from power supply, clean the suction pipe
Thepumpisnotprimed Followinstructions“PrimingThePump”
Theexternalin-linelteris
blocked
Cleantheexternallter
Theinletandoutletarenot
connected with the pipe or hose
correctly
Connect the inlet and outlet with pipe or hose correctly, ensure
thereisnoleakage.UseTeontapeonallconnections
Nowaterowfromsupply Check if the tank has plenty of water
YellowLEDashing System has reached cut off
pressure of 3.8 bar
Thisisnormaloperation.Thepumpwillstartautomaticallyonce
theoutletsystempressureisbelow1.5bar.Openoutlet.
Pump cannot be
started by pressing
Onbutton
Yellow LED on and
redLEDashing
Pump has gone to self protection
modeduetofrequenton/offcycle
Check if there are any leaks in the outlet system. Fix any leaks
found.EnsureTeontapeisusedonallconnections.Pumpmust
be disconnected from mains power to reset.

Produkt Specifikationer

Mærke: Ozito
Kategori: Pomp
Model: CPP-802

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito CPP-802 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Pomp Ozito Manualer

Ozito

Ozito PTP-012A Manual

15 Oktober 2024
Ozito

Ozito CPP-802 Manual

10 August 2024
Ozito

Ozito PTP-425 Manual

8 August 2024
Ozito

Ozito PSDW-750 Manual

3 August 2024
Ozito

Ozito PFFP-65E Manual

30 Juli 2024
Ozito

Ozito PSA-001 Manual

25 Juli 2024
Ozito

Ozito PXGTPS-0182 Manual

22 Juli 2024

Pomp Manualer

Nyeste Pomp Manualer

Little Giant

Little Giant OPWG-29 Manual

1 April 2025
Interphone

Interphone Air Pump 3000 Manual

1 April 2025
Grundfos

Grundfos UPS 20-60 N 150 Manual

1 April 2025
Grundfos

Grundfos UPS 40-50 FN 250 Manual

1 April 2025
Grundfos

Grundfos MTA 120-280 Manual

1 April 2025
Grundfos

Grundfos DMX 860-5 Manual

1 April 2025
Grundfos

Grundfos UPM4 Manual

1 April 2025
Grundfos

Grundfos DMH 880-10 Manual

1 April 2025
Grundfos

Grundfos MTA 200-280 Manual

1 April 2025
Grundfos

Grundfos MTSE 40-66 Manual

1 April 2025