Paasche FP-4P Manual

Paasche Ikke kategoriseret FP-4P

Læs gratis den danske manual til Paasche FP-4P (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Paasche FP-4P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTRUCTION AND PARTS LIST FP-4P 2/26/2018

Paasche Airbrush Company

9511 58th Place Kenosha, WI 53144

Website: paascheairbrush.com

E-Mail: info@paascheairbrush.com

Comes with LN-1/32 (Assembled) and LN-1/64, 3/64, and 1/16 Nibs loose

Total Length of Flow Pencil is 5 -1/2 inches.

Printed in the U.S.A.

INTRODUCTION:

The FP-4P Flow Pencil is used extensively by Cake Artists,

Bakers, and Home Bakers to decorate their Cakes, Cupcakes,

Cookies,etc. The Flow Pencil is easy to control and operate.

MIXING :

1. Proper mixing of Royal Icing & Butter Cream is essential for

continuous and uninterrupted flow.

2. Experiment with thinning of Icing for best flow.

3. Do not mix Icing in cup of Flow Pencil, use a separate

container and pour into cup only when Icing is at proper

consistency.

LOADING ICING: ( Tighten adjusting screw at rear of flow

pencil before loading Icing)

1. Remove FP-5 Cover, and pour premixed Icing into cup 3/4

full, Hold lid firmly and push plunger into cup, Pressure will

build and plunger will rise, thread lid onto cup.

2. Turning the MU-72 Adjusting Screw will control the

movement of the MU-65 Finger Lever Assembly which

controls the flow of Icing.

OPERATION:

1. Hold the FP-4P Flow Pencil in your hand as you would a

pencil or brush and place your finger lightly over the MU-65

Finger Lever. When ready to begin piping, pull back on the

MU-65 Finger Lever, when the icing begins to flow raise

the pencil up and pull in a backward motion off the surface

slightly.

2. Regulate the flow to the desired feed rate by turning

MU-72 Adjusting Screw.

3. When the plunger gets closer to the cap the flow rate will

slow down.

4. Practice on a Cake board before working on a actual cake.

5. Correct adjustment of controls and skill of operation will result

in uninterrupted and continuous piping.

CARE AND CLEANING:

1. Before storing FP-4P Flow Pencil clean it thoroughly. Rinse

cup and lid in hot water to clean out Icing,remove nib and clean

in hot water, wipe dry.

2. MU-49L Needle is held in position by MU-57 Needle Chuck

and VL-141 Locknut. Remove the needle by unscrewing the

MU-71 Handle and removing the spring. Loosen the VL-141

Locknut and then remove the needle for cleaning.

ADJUSTING OR REPLACING WORN PACKING WASHER:

1. If PTFE Packing-#6 becomes worn or loose it must be

tightened or replaced.

2. You will need a small screwdriver to remove or tighten the

Packing Nut.

3. When replacing your PTFE Packing press Packing onto the

Packing Nut-#6. Use a small screwdriver to tighten packing nut

into shell until it is tight then back out one-half turn, may vary.

4. Now insert needle - you should feel a slight resistance. If too

loose or too tight adjust the Packing Nut with screwdriver until

you feel some slight resistance.

5. Now completely re-assemble guts of Flow Pencil.

CAUTION: OVER TIGHTENING CUP WILL

CAUSE TRIGGER TO MALFUNCTION.

WARNING: Follow all safety precautions.

CAUTION: Never point flow pencil at face when pressurized.

FP-4P

(Pressure Fed)

Flow Pencil

OPERATING INSTRUCTIONS & REPLACEMENT PARTS

Page 2 FP- 4P Flow Pencil Parts List

No. Part No. Description

3 MU-9 Tip Nut

4 LN-1/32 Nib (1/64, 3/64 & 1/16 Sizes)

5 MU-48A Shell Assembly

6 MU-612 PTFE Packing & Packing Nut

8 MU-65 Finger Lever Assembly

11 MU-71 Handle

12 3A-4 “O” Ring

13 MU-72 Adjusting Screw

14 MU-57 Needle Chuck

15 MU-49L Needle

No. Part No. Description

16 VL-141 Locknut

18 SpringVL-140

32 MU-77 Stand

24 Pressure CupFP-45

(new male thread)

25 MU-25 Rod & Cap Assembly

26 Nut MU-69

27 FP-5 Cover (only)

28 MU-26 Spring

29 MU-70 Piston

30 MT-21 “O” Ring

31 FP-6 Cup (only) Aluminum

33 “O” RingAE-43

FP-4P FLOW PENCIL (WITH EXTRA NIBS: LN-1/64, 3/64 AND 1/16)

Nibs are grooved as follows:

LN-1/64 has one (1) groove

LN-1/32 has two (2) grooves

LN-3/64 has three (3) grooves

LN-1/16 has four (4) grooves

Contains Aluminum

Contains Brass

Contains Stainless Steel

Contains FDA Approved Silicone

Produkt Specifikationer

Mærke:	Paasche
Kategori:	Ikke kategoriseret
Model:	FP-4P

Har du brug for hjælp?

Hvis du har brug for hjælp til Paasche FP-4P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Paasche Manualer

Paasche 2000SI Manual

22 August 2024

Paasche VL-1AS Manual

22 August 2024

Paasche TS-3AS Manual

22 August 2024

Paasche D220R Manual

22 August 2024

Paasche VL-100D Manual

22 August 2024

Paasche RG-3AS Manual

22 August 2024

Paasche TG-1AS Manual

22 August 2024

Paasche H-100D Manual

22 August 2024

Paasche FP-1/32 Manual

22 August 2024

Paasche H-3AS Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Synology CMA-01 Manual

1 August 2025

Synology RKS-02 Manual

1 August 2025

Navman MiVue 765 SAFETY Manual

1 August 2025

Navman MY75T Manual

1 August 2025

Exquisit AIRFRY 3010 Manual

1 August 2025

Navman MiVue 155 SAFETY Manual

1 August 2025

Navman MiVue 698 Manual

1 August 2025

Newland FM550 Manual

1 August 2025

Tripp Lite SRIN4181810 Manual

1 August 2025

Navman MyTruck III Manual

1 August 2025