PAC AP4-TY11 Manual

PAC Modtager AP4-TY11

Læs gratis den danske manual til PAC AP4-TY11 (10 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 17 anmeldelser. Har du et spørgsmål om PAC AP4-TY11, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

PAC-audio.com

Page 1

Rev: V2

Date:032718

Advanced Amplier Interface

for Toyota / Lexus

AP4-TY11

The AP4-TY11 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range,

xed level head unit output, in conjunction with data bus messages, the AP4-TY11 delivers a variable 5v RMS pre-

amp output with fading, balance, equalization, and level control capabilities. The module also retains audio from

other vehicle features such as factory navigation prompts, Bluetooth and Voice Activation. An accessory controlled

remote amplier turn on wire is also provided by the AP4-TY11. When used in conjunction with the APA-TOS1 (sold

separately), the module can provide a variable 2-channel ber optic digital audio output (TOSLINK).

Introduction and Features

Important Notes

Wiring Connection Chart

To Aftermarket

Amplifier

Non-FadingRearFront

1(L) 2(R) 4(R) 5(L) 6(R)3(L)

Remote Turn On Output (2A Max)

Mute Input From Navigation

Mute Input From Telematics

To Amp PRO*

*Connections “To Amp PRO”, “A”, “B” and “C”

are discussed in detail starting on page 5 under

“Voice / Nav Audio Connections”.

To Vehicle

Harness

To Radio

Non-Fading

Level Control

Knob

AP4-TY11-HAR

To Radio

1. Only compatible in vehicles equipped with a data bus controlled premium sound system. To verify compatibility in Toyota,

look for a JBL logo on the radio. In Lexus applications, most compatible radios will have a factory subwoofer or center

channel. RX Series Lexus are always amplied regardless if they do or do not have a center channel or subwoofer. Always

check PAC-audio.com for radio specic compatibility notes based on the year, make and model of the vehicle.

2. Voice activation / navigation prompt audio requires the AP4-TY11 harness to be connected for the proper conguration for

the vehicle. See the Vehicle Connections Chart starting on page 2 for details.

3. The factory radio's speed controlled volume, DSP, and surround sound mode are not supported by the AP4 outputs.

4. The factory amplier must remain connected, and in the vehicle after the AmpPRO has been installed.

5. Prior to testing, cycle the ignition off and back on again to properly initilize the AP4-TY11.

6. The AP4-TY11 beep volume and minimum volume levels are set to 0 dB by default. If you are happy with this level in your

particular application, additional adjustment is not required. Please refer to the Setup and Conguration section on page 9

for more details.

7. The remote output is rated at 2A of current. If more current is needed, an external relay must be used.

8. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level

control knob.

9. The level control knob must be connected in order to manually adjust the beep volume and minimum volume settings.

10. Due to variations in output levels between various OEM radios and even between radio modes, the AP4-TY11 output

voltage may vary from the selected 5 volt (or 4 volt when DIP switch 2 is down) output.

11. Toyota Safety Connect and Lexus Enform (SOS) can easily be retained. See the Tech Brief "AP4-TY SOS Retention" at

PAC-audio.com for detailed instructions.

PAC-audio.com

Page 2

Rev: V2

Date:032718

Advanced Amplier Interface

for Toyota / Lexus

AP4-TY11

Vehicle Connections Chart

The connections chart provides the information necessary to retain the voice prompts and navigation audio along with details

of where to nd the factory amplier, and in some cases, location of the factory navigation module. In vehicles with navigation

and / or a voice button on the steering wheel, locate your vehicle on this chart to determine which cong you will use. If the

vehicle does not have the voice button on the steering wheel and it does not have navigation, this information will not pertain to

the installation.

Use the chart to determine which Conguration to use, and the location of the amplier and navigation module (when

applicable). Under the "Cong Type" column, if it is listed as "A" it is cong type A, "B" is cong type "B" and Cong type C is

listed as the 3 possible versions. "C v1" is cong type C version 1, "C v2" is cong. type C version 2, and "C v3" is cong C

version 3. See the appropriate section covered on pages 5 thru 8 regarding the connections covered in the chart. If there is

an N / A listed for the vehicle, the information in that column does not pertain to your vehicle. The "Nav Input Audio" and "Nav

Output Audio" information describes the wiring and connector found at the navigation module.

Toyota

Model Years Cong Type OEM Amp Location Nav Module Location Nav Input Audio Nav Output Audio

4Runner 2003 - 2005 C v3 Behind Right Rear Side *

Panel in Rear Cargo Area

Over Right Rear Tire Well

In Rear Cargo Area

18 Pin Connector

Pin 1 (+) Light Green

Pin 10 (-) Blue

18 Pin Connector

Pin 2 (+) Light Green

Pin 11 (-) Blue

4Runner 2006 - 2013 A Behind Right Rear Side

Panel in Rear Cargo Area

N / A N / A N / A

Avalon 2005 - 2007 C v3 Under Front Right Seat Left Side of Luggage

Compartment

18 Pin Connector

Pin 1 (+) Gray

Pin 10 (-) Yellow

18 Pin Connector

Pin 2 (+) Pink

Pin 11 (-) Violet

Avalon 2008 - 2010 Non Nav: A

Nav: C v3

Under Front Right Seat Left Side of Luggage

Compartment

18 Pin Connector

Pin 1 (+) Gray

Pin 10 (-) Yellow

18 Pin Connector

Pin 2 (+) Pink

Pin 11 (-) Violet

Avalon 2011 - 2012 A Under Front Right Seat N / A N / A N / A

Avalon 2013 - 2014 B Under Front Left Seat N / A N / A N / A

Camry 2007 - 2011 A Under Front Right Seat N / A N / A N / A

Camry 2012 - 2014 B Under Front Left Seat N / A N / A N / A

Corolla 2005 - 2008 Under Front Right SeatN / A N / A N / A N / A

Corolla 2009 - 2011 A Under Front Right Seat N / A N / A N / A

FJ Cruiser 2011 - 2014 A Behind Right Rear Side

Panel in Rear Cargo Area

N / A N / A N / A

Highlander 2008 - 2010 A Under Front Right Seat N / A N / A N / A

Highlander 2011 - 2013 ** Radio and

Display: B

All Others: A

Under Front Right Seat N / A N / A N / A

Prius 2004 - 2005 C v1 Under Front Right Seat Pin 22 (+) White N / A N / A

Pin 21 (-) Black

Prius 2006- 2009 C v2 Under Front Right Seat Pin 25 (+) Green N / A N / A

Pin 26 (-) Red

Prius 2010 - 2011 A Under Front Right Seat N / A N / A N / A

Prius 2012 - 2015 B Under Front Right Seat N / A N / A N / A

Rav4 2004 - 2006 Behind Right Rear Side N / A

Panel in Rear Cargo Area

N / A N / A N / A

Produkt Specifikationer

Mærke:	PAC
Kategori:	Modtager
Model:	AP4-TY11

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC AP4-TY11 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager PAC Manualer

30 Juli 2025

29 Juli 2025

17 Februar 2025

11 Februar 2025

11 Februar 2025

8 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Atlona AT-HDR-CAT-4ED Manual

15 September 2025

Ibiza Sound SA2000 Manual

15 September 2025

Sony HCD-SH2000 Manual

15 September 2025

AMX NMX-ENC-N2612S Manual

14 September 2025

AMX UDM-RX02N Manual

14 September 2025

AMX AVB-RX-DXLINK-HDMI Manual

14 September 2025

Perreaux Silhouette SXH2 Manual

13 September 2025

Perreaux Silhouette SXP2 Manual

13 September 2025

Perreaux Silhouette SX25i Manual

12 September 2025

Perreaux Silhouette SXV2 Manual

12 September 2025