Panamax MOD-AT2 Manual

Panamax PowerBank MOD-AT2

Læs gratis den danske manual til Panamax MOD-AT2 (2 sider) i kategorien PowerBank. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Panamax MOD-AT2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

800-472-5555 www.panamax.com

INSTRUCTIONS FOR PANAMAX SIGNAL LINE PROTECTION MODULES - PREMIUM SERIES

When properly installed, the base unit’s Connected Equipment Protection Policy

remains valid. All modules include a small rectangular bracket and mounting screws. This

bracket replaces the small triangular wall-mount bracket that comes with the models listed in

the CURRENT PRODUCTS above.

Module

Bracket

AC Base Unit

Ground

Connector

Ground

Connector

Ground

Connector

Pull Out Card

The MOD-AT4 module is designed to pro-

tect standard phone lines and DSL (ADSL,

G.Lite) lines. Multiple input & output jacks

provide complete installation flexibility. The

following diagram shows how the

jacks/wires are interconnected. Different

cables/connections can be split or com-

bined to accommodate a variety of installa-

tions. For example:

• Incoming lines can be punched-down on

the 110 jack on the side and four RJ11LINE

(single-line) cords will connect from the

EQUIP side to the equipment.

• Two RJ14 (dual-line) cords connected to

the LINE side (upper 2 jacks) can be split to

four RJ11 (single-line) cords on the EQUIP

side.

• Four RJ11 (single-line) cords connected

to the side can be combined into aLINE

single RJ45 (8 wire) cord (upper jack) on the

EQUIP side.

Caution: Never install telephones

during a lightning storm.

The MOD-AT8110 module is designed to

protect up to 8 standard phone lines using

110 punchdown connectors on both the

input LINE EQUIPand output .

1. Cut the cable from the primary protector

to the correct length and punch down the

cable to the punchdown block onLINE IN

the module.

2. Punch down another cable to the EQUIP

OUT punchdown block on the module and

connect to the phone equipment.

MOD-AT4

EQUIP

OUT

RJ-45

LINE

RJ-45

EQUIP

OUT

RJ-14

LINE

RJ-14

EQUIP

OUT

RJ-11

LINE

RJ-11

LINE

RJ-11

EQUIP

OUT

RJ-11

EQUIP

OUT

S110D

Pull Out

LINE

S110D

MOD-AT4

EQUIP

OUT

RJ-45

LINE

RJ-45

EQUIP

OUT

RJ-14

LINE

RJ-14

EQUIP

OUT

RJ-11

LINE

RJ-11

LINE

RJ-11

EQUIP

OUT

RJ-11

EQUIP

OUT

S110D

Pull Out

LINE

S110D

Bl Bl

Or Or

Gr Gr

Br Br

1 - 8 1 - 41 - 41 - 4

1 - 8

1 - 41 - 41 - 4

WIRING DIAGRAM AND SPECIFICATIONS

MOD-AT4

For Analog

Telephone

Lines

• 4 Pairs (8 wires) Protected

• 260 Volt Clam

ping • Straight-Through Pinout

Blue

Blue Blue

Blue

Orange

Orange Orange

Orange

Green

Green Green

Green

Brown

Brown Brown

Brown

MOD-AT8110

For Analog Telephone Lines

• 16 Wires (two 110 punch-downs) Protected

• 260 Volt Clamping

• Auto-resetting PTC's

110

IDC

110

IDC

WIRING DIAGRAM AND SPECIFICATIONS

LINE

S110D

EQUIP

OUT

S110D

MOD-AT8110

Pull Out

LINE

S110D

EQUIP

OUT

S110D

MOD-AT8110

Pull Out

The MOD-AT2 module is designed to protect

standard phone lines connected to computer

modems, telephones, pay-per-view ports, etc.

It will also protect DSL lines (ADSL, G.Lite)

going into the DSL modem. The MOD-AT2

module will protect a single phone line using

an RJ-11 (2 wire) cord or a dual phone line

using an RJ-14 (4 wire) cord.

1. Connect the telephone line to the LINE

jack on the module.

2. Use a modular cord to connect the

EQUIP modular jack to the equipment to be

protected.

1 - 8

MOD-AT2

For Analog Telephone Lines

• 4 Wires (1 RJ-14) Protected

• 260 Volt Clamping

• Auto-resetting PTC's

1 - 8

WIRING DIAGRAM AND SPECIFICATIONS

MOD-AT2

EQUIP

OUT

LINE

Pull Out

MOD-AT2

EQUIP

OUT

LINE

Pull Out

SAT

CATV

It is very important to connect

telephone signal lines properly.

1. Mount the rectangular bracket to the back

of the AC base unit with the #8-32 x 5/16”

machine screws.

Note: The brass ground connector must be

used with the bracket in order to bond the

module ground to the base unit’s ground.

2. Mount the signal line module to the

bracket (screws provided with the module).

3. Optional – The assembled base unit and

module(s) may be wall mounted if desired.

4. Connect the wiring to the signal line

module as shown in the appropriate follow-

ing section.

MOD-AT2 MOD-AT4 MOD-AT8110 MOD-DT4

MOD-UTP MOD-CAT5 MOD-DBSTV MOD-SPKP

These modules are approved accessories for use with compatible Panamax AC

base units. Compatible base units include the following:

There are no designated

input/output connections

on coaxial protection

modules. These are

bi-directional modules

in both transmission fre-

quency and voltage.

All telephone input/output connections will

be labeled with LINE EQUIP.and

Model: MOD-AT8110 (Secondary Protector)

Model: MOD-AT4 (Secondary Protector)

Installation Instructions

Model: MOD-AT2 (Secondary Protector)

MOD-DT4

EQUIP

OUT

RJ-45

LINE

RJ-45

EQUIP

OUT

RJ-14

LINE

RJ-14

EQUIP

OUT

RJ-11

LINE

RJ-11

LINE

RJ-11

EQUIP

OUT

RJ-11

EQUIP

OUT

S110D

Pull Out

LINE

S110D

EQUIP.

OUT

LINE

MOD-UTP

Pull Out

Pul Out

MOD-CAT5

MOD-DBSTV

E UIPQ

OUT

RJ-11

LINE

RJ-11

SAT /

CATV

P tul l Ou

Card

SAT /

CATV

SAT /

CATV

OUTSIDE LINES

MOD-SPKP

RECEIVER

Pull Out

An easy access

PULL OUT card

is included on

the back of each

module for wiring

diagrams and

specifications.

CURRENT PRODUCTS

AC Base Units

DISCONTINUED PRODUCTS

AC Base Units

PM8-EX

PM8T-EX

PM8C-EX

PM8DBS-EX

M4-EX

M4T-EX

M8-EX

M8C-EX

M8HT-PRO

M8-HT

PM8-HT

M8C-EX

M8DBS-EX

M8C-Pro

M8HC-Pro

M4T

M4L

M8T

M8C

M8KSU

M8COM

M8KSU

LINE

EQUIP.

OUT

Produkt Specifikationer

Mærke:	Panamax
Kategori:	PowerBank
Model:	MOD-AT2
Vægt:	1472.9 g
Produktfarve:	Grå
Dimensioner (BxDxH):	184.1 x 158.7 x 139.7 mm
AC udgange, antal:	2 AC stikkontakt(er)
Telefonlinje beskyttelse:	Ja
Netværk linje beskyttelse:	Ja
Indgangsforbindelser:	RJ-14