Panasonic EX33PN Manual

Panasonic Ikke kategoriseret EX33PN

Læs gratis den danske manual til Panasonic EX33PN (16 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Panasonic EX33PN, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/16
ENDEESIT FR
EX-30
Instruction manual
Betriebsanleitung
Manual de Instrucciones
Manuel d’instructions
Manuale d'istruzioni
1
n
MEUML-EX30 V1.0
Thank you very much for using SUNX products. Please read this Instruction
Manual carefully and thoroughly for the correct and optimum use of this
product. Kindly keep this manual in a convenient place for quick reference.
This product has been developed / produced for industrial use only.
A thin 0.1mm2 cable is used for this product. Do not use excessive force
when pulling on the cable: it may cause cable to break.
You can extend the cable up to 50m max. with 0.3mm
2 or more cable for
both emitter and receiver (thru-beam types). However, in order to reduce
noise, make the wiring as short as possible.
Do not apply stress directly to the sensor cable joint by forcibly bending
or pulling.
Make sure that the power supply is off while wiring.
Incorrect wiring will damage the sensor.
Do not run the wires together with high-voltage lines or power lines or put
them in the same raceway. This can cause malfunction due to induction.
Verify that the supply voltage including the ripple is within the rating.
If power is supplied from a commercial switching regulator, ensure that
the frame ground (F.G.) terminal of the power supply is connected to an
actual ground.
In case noise generating equipment (switching regulator, inverter motor,
etc.) is used in the vicinity of this product, connect the frame ground
(F.G.) terminal of the equipment to an actual ground.
Do not use during the initial transient time (0.5s) after the power supply is
switched on.
Make sure to use an isolation transformer for the DC power supply. If an
auto-transformer (single winding transformer) is used, this product or the
power supply may be damaged.
If it is possible that the power supply used may generate a surge,
connect a surge absorber to the power supply.
Ensure that the sensor is not directly exposed to the following light
sources as they may adversely effect sensing performance: fluorescent
light from a rapid-starter lamp, a high frequency lighting device, sunlight
etc.
Avoid dust, dirt and steam.
Take care that the sensor does not come in contact with oil, grease,
organic solvents such as thinner, etc., strong acid, or alkalines.
If the sensor is operating where static electricity is present, use a
grounded metal mounting plate.
Sensitivity adjustment is available for EX-32 and EX-33.
When EX-32 is used, adjust the sensitivity as follows. When EX-33 is
used, set the sensitivity adjuster to the MAX. position. However, if the beam
penetrates a sensing object, adjust the sensitivity as follows.
Procedure
This procedure assumes that “Light-ON” is set for the operation mode. If
“Dark-ON” is the operation mode, the output will behave the other way
around.
Use a standard screwdriver and turn the adjuster slowly. Using
excessive force will damage the adjuster.
INSTRUCTION MANUAL
Photoelectric Sensor
EX-30 Series
WARNING
• Never use this product as a sensing device for personnel protection.
• In case of using sensing devices for personnel protection, use
products which meet laws and standards, such as OSHA, ANSI or IEC
etc., for personnel protection applicable in each region or country.
1CAUTIONS
2PART DESCRIPTION
No. Part Description
1Operation indicator
(orange)*1
*1For the thru-beam type sensor, located on the receiver.
Lit when the output is ON.
2Stability indicator
(green)*1
Lit when detection is stable according
to the parameters set.
3Sensitivity adjuster
*2
*2Incorporated on the emitter for EX-33 and EX-32. Not incorporated for
EX-31.
Sensing range increased when turned
clockwise.
4Operation mode
switch
EX-33
only.
• L: Light-ON
Turn the operation mode
switch fully clockwise
until it stops.
• D: Dark-ON
Turn the operation mode
switch fully
counterclockwise until it
stops.
3SENSITIVITY ADJUSTMENT
Step Sensitivity
adjuster Description
1Turn the sensitivity adjuster fully counterclock-
wise to the minimum sensitivity position.
2In the “light received” condition, turn the sen-
sitivity adjuster slowly clockwise to find point
A where the sensor output turns ON.
*1
12
3
4
L
D
L
D
MAX
MAX

Produkt Specifikationer

Mærke: Panasonic
Kategori: Ikke kategoriseret
Model: EX33PN

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic EX33PN stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Panasonic Manualer

Panasonic

Panasonic CS-BKP Manual

1 Juli 2025
Panasonic

Panasonic CS_CU-E9CKP Manual

1 Juli 2025
Panasonic

Panasonic CQ-DPX151U Manual

30 Juni 2025
Panasonic

Panasonic CS-2C19BKP5G Manual

30 Juni 2025
Panasonic

Panasonic CS-C24 Manual

29 Juni 2025
Panasonic

Panasonic CS-12CKE Manual

29 Juni 2025
Panasonic

Panasonic CS-E15CKP Manual

27 Juni 2025
Panasonic

Panasonic CS-E12 Manual

27 Juni 2025
Panasonic

Panasonic CS-V24BKP Manual

24 Juni 2025
Panasonic

Panasonic CS-V18 Manual

24 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Schneider

Schneider LUCD1XES Manual

4 Juli 2025
Ikea

Ikea BLÄDDRARE 304.743.99 Manual

4 Juli 2025
NUX

NUX Komp Core Deluxe MKII Manual

4 Juli 2025
Ikea

Ikea GRÖNAMARANT 204.604.25 Manual

4 Juli 2025
Rowenta

Rowenta Focus DW5121 Manual

4 Juli 2025
Racktime

Racktime Baskit Breeze 2.0 Manual

4 Juli 2025
Schneider

Schneider KSB32CP15D Manual

4 Juli 2025
Wiesenfield

Wiesenfield WIE-IN-100 Manual

4 Juli 2025
Ergotec

Ergotec PM-705N Manual

4 Juli 2025
Sol Expert

Sol Expert 19590 Manual

4 Juli 2025