Panduit CT-1090 Manual

Panduit Håndværktøj CT-1090

Læs gratis den danske manual til Panduit CT-1090 (2 sider) i kategorien Håndværktøj. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Panduit CT-1090, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Page: 1 of 2

CONTROLLED CYCLE FERRULE CRIMPING TOOL

OPERATION, INSPECTION and MAINTENANCE INSTRUCTIONS

1. With the handles in the open position, insert the ferrule

into the crimp pocket. Make sure that the ferrule is

inserted fully into the crimp die (see Figure 2).

2. Insert the stripped wire into the ferrule until the wire

stops. Refer to product packaging for wire strip length.

3. Crimp the ferrule by closing the handles until the

controlled cycle mechanism releases. Upon release,

the handles will open automatically and the crimped

ferrule can be removed.

NOTE: Crimp entire uninsulated ferrule length. This may

require additional crimps.

CT-1090 TOOL

Fig. 1

Fig. 2

Stripped

Wire

Crimp Die

Controlled cycle mechanism

prevents tool from opening

before crimp cycle is completed.

Manual release lever, push

forward in the event that

controlled cycle mechanism

must be released.

Cushioned handle grips

CRIMP POCKETS for Ferrule

terminals. Refer to product

packaging for wire range and

proper crimp pocket. Crimp

pockets are identified with

applicable wire range.

Ferrule - Wire

crimp section

Ferrule Insulated

section

CT-1090

PA28190A01

REV: 00 9-2016

E-mail:

techsupport@panduit.com

For Technical Support:

1-800-777-3300

www.panduit.com

CAUTION:

Verify power is “OFF” before working on

wiring with these tools.

The plastic grips are for the user’s

comfort, and are not intended

to insulate against electrical shock while

working on live electrical circuits.

INSPECTION / MAINTENANCE

NEW TOOLS -

BEFORE PLACING INTO SERVICE:

All Panduit crimping tools are inspected before they are

shipped from the factory. All new tools should be

inspected before being used.

New tools are shipped, factory lubricated, in protective

packaging. After inspection, simply clean any excess oil

from the crimping dies and place into service.

When the tool is not in use, keep the handles closed to

prevent objects from becoming lodged in the crimping

area. Store the tool in a clean, dry area.

Page: 2 of 2

IN SERVICE TOOLS - AFTER TOOLS HAVE BEEN IN SERVICE:

It is recommended that each operator of the tool be made aware of - and responsible for following these maintenance

steps:

In-service tools should be cleaned and inspected at least ONCE A MONTH. To clean - wipe with a clean cloth.

In-service tools should be lubricated ONCE A WEEK, and after every cleaning. Lubricate all pins, pivots and bearing

surfaces with DOW CORNING®Molykote BR2 Plus.

Be sure to clean any excess oil from the crimping dies before using.

®Molykote BR2 Plus is the Registered Trademark of DOW CORNING.

VISUAL INSPECTION

1. Visually inspect the tool for missing or loose pins; then close the tool and note the return action of the handles.

2. Inspect the crimping dies for worn, chipped or broken edges.

3. If parts are missing, defective or damaged; contact Panduit for information on repair or replacement of tools.

4. Check for debris in dies. Any debris will need to be removed prior to tool use.

and MAINTENANCE INSTRUCTIONS CT-1090

Produkt Specifikationer

Mærke:	Panduit
Kategori:	Håndværktøj
Model:	CT-1090

Har du brug for hjælp?

Hvis du har brug for hjælp til Panduit CT-1090 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Håndværktøj Panduit Manualer

Panduit CT-2980/STBT Manual

25 August 2025

Panduit CT-1250 Manual

29 December 2024

Panduit CT-2931/STBT Manual

6 September 2024

Panduit CT-3980/BT Manual

6 September 2024

Panduit CT-2940/STBT Manual

6 September 2024

Panduit CT-2920/CCPBT Manual

6 September 2024

Panduit CT-3001/CCPBT Manual

5 September 2024

Panduit CT-3001/STBT Manual

5 September 2024

Panduit CT-2600/LBT Manual

5 September 2024

Panduit CT-1090 Manual

20 August 2024

Håndværktøj Manualer

Nyeste Håndværktøj Manualer

Klein Tools 3000CRKIT Manual

25 September 2025

Klein Tools 3007CR Manual

17 September 2025

Biltema 19-234 Manual

14 September 2025

Blaupunkt CL3010 Manual

8 September 2025

Blaupunkt CS4120 Manual

8 September 2025

Blaupunkt CS3120 Manual

8 September 2025

Blaupunkt CL7010 Manual

8 September 2025

Beha-Amprobe Universal Cabinet Key Manual

7 September 2025

Klein Tools VDV100-801 Manual

6 September 2025

Blaupunkt LB3010 Manual

29 August 2025