Perel E300GSM Manual

Perel Måleudstyr E300GSM

Læs gratis den danske manual til Perel E300GSM (16 sider) i kategorien Måleudstyr. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Perel E300GSM, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/16
E300GSM
V. 03 22/10/2018 1 ©Velleman nv –
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal
of the device after its lifecycle could harm the environment. Do
not dispose of the unit (or batteries) as unsorted municipal
waste; it should be taken to a specialized company for recycling.
This device should be returned to your distributor or to a local
recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Perel! Please read the manual thoroughly before
bringing this device into service. If the device was damaged in transit, do not
install or use it and contact your dealer.
2. Safety Instructions
● This device can be used by children aged from 8 years and above, and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning the use of the device in a safe way and understand the hazards
involved. Children shall not play with the device. Cleaning and user
maintenance shall not be made by children without supervision. Indoor use ●
only. Keep this device away from rain, moisture, splashing and dripping
liquids Risk of electroshock when opening the cover. Touching live wires . ●
can cause life-threatening electroshocks. Familiarise yourself with the ●
functions of the device before actually using it. All modifications of the ●
device are forbidden for safety reasons. Damage caused by user modifications
to the device is not covered by the warranty. Damage caused by disregard ●
of certain guidelines in this manual is not covered by the warranty and the
dealer will not accept responsibility for any ensuing defects or problems.
● ● Keep this manual for future reference. Refer to the Velleman
® Service and
Quality Warranty on www.velleman.eu.
3. Overview
1. M button
5. SIM card slot
2. antenna
6. USB connector (firmware
3. GSM status LED
upgrade only)
4. power LED
7. temperature sensor slot
GSM status LED:
Slow blinking: no GSM signal
Normal blinking: GSM signal fixed
Fast blinking: send or receive SMS
4. Power Control Connector
input
output
Input: 110- 230 V~
L: live
N: negative
G: ground
Output: 110- 230 V~
L: live
N: negative
G: ground
12V: output and alarm sensor input
12V: constant 12 VDC output (max. 200 mA)
S1: wired sensor input 1, NO/NC type
S2: wired sensor input 2, NO/NC type
12V(C): controllable 12 VDC output (max. 200 mA) (only via SMS)
5. Start
● ● SIM card’s Connect the antenna to the power control. Deactivate the PIN
code using your cell phone. Install your SIM card (standard format) Make ●.
sure to insert it fully into the slot Connect the temperature sensor if . ●
desired. Connect the power input and output. Make sure to cut off the ●
power supply prior to connecting! Reconnect the power. The LED will light ●
within 3 to 5 seconds.
6. Registering a Phone Number
This power control accepts up to five phone numbers, i.e. one master number
and four auxiliary numbers The master number has full authorization to .
configure the devices. The auxiliary numbers can only be added by the
master number. All configurations are processed by sending an SMS to the
device’s SIM card. The SMS format is #code-1#code-2#.
Register the master number: # # 00
Add an auxiliary number: # #User-number# 06
Delete an auxiliary number: # #User-number# 15
Manually reset the device to delete the old master number if the device
replies [Master number already exists]. Hold the M button pressed for ten
seconds to return to the factory settings.
7. Free-Calling Control
A master or auxiliary number calling the SIM card number is able to switch
the 230 V power on or off for a few seconds.
Call to switch on/off the power output: #09#1#
When a user is calling, the switched on power will switch off and vice
versa.
Call to switch on/off the power output for a few seconds: #09#2#time#
Time parameters: 1-1800, i.e. duration 1-1800 seconds.
Switch off calling control function: #09#0#
8. Power On/Off
Any registered user can send an SMS to switch the 230 V power on/off.
Switch on power: #01#0#
Switch off power: 2#0# #0
9. Delay Control
Automatically switch the 230 V power on/off for a few minutes. Valid only for
the master number.
Switch on power for a few minutes: 2#0#time#0# #1
Switch off power for a few minutes: 2#0#time#1# #1
Time range: 1-720, i.e. duration 1-720 minutes.
Manually switch on/off the device to abort this function automatically.
10. Schedule Control
Automatically switch the 230 V power on/off according to the set schedule.
Valid only for the master number.
Set switch-on schedule: #20#0#day#start-time#end-time#
It will switch on the power at set time.
Day: one digit, see table.
value
day
value
day
0
Every day
5
Friday
1
Monday
6
Saturday
2
Tuesday
7
Sunday
3
Wednesday
8
Monday-Friday
4
Thursday
9
Weekend
Start-time and end-time: four digits (hhmm) in 24h-format.
Example: #20#0#0#2000#0800# means every day, power on at
20 08:00, power off at :00 the next day.
Activate schedule control function: #19#0#1#
Manually switch on/off the device to abort this function automatically.
E300GSM
V. 03 22/10/2018 2 ©Velleman nv –
11. Temperature Control
Connect the included temperature sensor. The temperature will be displayed
in an SMS.
The temperature control function is useful when the power output is
connected to a heating or cooling device. The power will automatically switch
on/off according to temperature changes.
Set control parameters: #24#0#mode#low-temp#high-temp#
Mode parameters: 1 (warming) or 2 (cooling).
Temperature range: - °C to 100 °C. 30
Example: #24#0#1#15#25# means power on when
temperature < °C, power off when temperature > . 15 25 °C
Activate temperature control function: # #0#1# 23
Manually switch on/off the device to abort this function automatically.
12. Temperature Alarm
Connect the included temperature sensor. You will be notified by SMS when
the temperature is out of range.
Set alarm range 2#0#low-temp#high-temp# : #2
Temperature range: - °C to 100 °C. 30
Activate temperature alarm: # #0#1# 21
Deactivate temperature alarm: # #0#0# 21
13. Wired Sensor Alarm
The power control accepts two wired sensor inputs, one constant 12 VDC
output and one controllable 12 VDC output. The constant 12 VDC output can
act as a power supply for the wired sensors. The input sensors are of the
NO/NC type. Connect the wired sensors and COM PIN to the S1 and S2
terminals. Do not connect S1 and S2 to the power supply as this can
irreversibly damage the device.
The power control will send an SMS when the sensor is triggered.
SMS when sensor alarm on: #40#1#
SMS when sensor alarm off: #40#0#
Change sensor name: #43#sensor-1#sensor- 2#
Example: #43#door#window# means door = sensor 1,
window = sensor 2. The respective name will appear in the SMS.
Change alarm mode: #44#sensor-number#mode#
Sensor number: 1 or 2. Mode: 1, 2 or 3. Mode 1: NC (only alarm when
two terminals are open), mode 2: NO (only alarm when two terminals
are closed), mode 3: NO/NC (only alarm when two terminals are open
or closed).
14. Auto Control When Triggered
Use this function as a smart control for your home, e.g. as motion detector.
Sensor trigger, auto turn on 230 V power: #42#220#time#
Time range: 1-1800, i.e. turn on power for 1-1800 seconds. Function
turn off at set time 0 (default value ).
Sensor trigger, auto turn on 12 VDC power: #42#12#time#
Time range: 1-1800, i.e. turn on power for 1-1800 seconds. Function
turn off at set time 0 (default value = 60 ).
A triggered sensor can switch on 230 V and 12 VDC according to the settings.
15. Advanced Settings
SMS when on/off button pressed
Default send SMS when M button is pressed.
SMS when on-off button pressed on: #03#1#
SMS when on-off button pressed off: #03#0#
SMS when power lost or restore
Default send SMS when main power supply is lost or restored.
SMS when power lost or restored on: 5#1# #0
SMS when power lost or restored off: 5#0# #0
SMS when calling operation
Default send SMS when calling.
SMS when calling on: # #1# 41
SMS when calling off (default): # #0# 41
Reset factory settings
There are two methods to restore the factory settings:
Method 1: The master uses sends an SMS.
Reset factory settings: #08#1234#
Method 2: Hold the M button pressed for ten seconds. The factory settings
are re-loaded after the beep.
16. SMS Command List
category
function
command
Define users
Register master number
#00#
Add family number
#06#family-number#
Check family number
#06#
Delete family number
#15#family-number#
Delete all family numbers
#15##
Power control
Set calling to switch power
#09#1#
Set calling to switch on
power for some seconds
#09#2#time#
Switch off calling function
#09#2#
Power on
#01#0#
Power off
#02#0#
Delay control
Turn off power for some
minutes
#12#0#minutes#1#
Turn on power for some
minutes
#12#0#minutes#0#
Schedule control
Schedule control on
#19#0#1#
Set schedule control
parameters
#20#0#workday#
starttime#endtime#
Temp control
Temp control on
#23#0#1#
Set temp control parameters
#24#0#mode#
low-temp#high-temp#
warming=1, cooling=2
Temp alarm
Temp alarm on
#23#0#1#
Set temp range
#22#0#mintemp#maxtemp#
Temp alarm off (default)
#21#0#1#
Sensor alarm
Sensor alarm on
#40#1#
Sensor alarm off
#40#0#
Change sensor name
#43#sensor1#sensor2#
Change alarm mode
#44#sensor-number#mode#
Sensor trigger, turn
on power
Sensor trigger, auto turn on
230 V power
#42#220#time#
Sensor trigger, auto turn on
12 VDC power
#42#12#time#
SMS notifications
SMS when on-off button
pressed on (default)
#03#1#
SMS when on-off button
pressed off
#03#0#
SMS when power lost or
restore on (default)
#05#1#
SMS when power lost or
restore off
#05#0#
SMS when calling on
#41#1#
SMS when calling off (default)
#41#0#
SMS to users on (default)
#16#1#
SMS to users off
#16#0#
Check status
Check status
# 07#
Check delay control status
# 34#
Check schedule control
status
# 33#
Check temp control status
# 32#
Check temp alarm status
# 35#
Check GSM signal
# 27#
GSM signal alert on
#27#1#
GSM signal alert off (default)
#27#0#
Reset
Reset factory setting
#08#1234#
17. Cleaning and Maintenance
Occasionally wipe with a damp cloth occasionally to keep it looking new. Do
not use harsh chemicals, cleaning solvents or strong detergents.
18. Technical Specifications
1 channel
max. power loading .............................. 3500 W, 16 A (two lines control)
power input ........................................................ 110-230 V~, 50/60 Hz
power output ................... 110-230 V~, 50/60 Hz, 12 VDC (max. 200 mA)
GSM frequency ............................................... 850/900/1800/1900 MHz
SIM card slot ......................................................standard size SIM card
wired sensor input ..................... NO (normal closed) or NC (normal open)
wired sensor cable length ................................................ 2 m (included)
GSM antenna .......................................................................... included
dimensions ............................... 90 x 70 x 73 mm (without GSM antenna)
weight .......................................................................................222 g
max. users ......................................................... 5 (1 master / 4 users)
Use this device with original accessories only. Velleman nv cannot be
held responsible in the event of damage or injury resulting from
(incorrect) use of this device. For more info concerning this product
and the latest version of this manual, please visit our website
www.perel.eu. The information in this manual is subject to change
without prior notice.

Produkt Specifikationer

Mærke: Perel
Kategori: Måleudstyr
Model: E300GSM

Har du brug for hjælp?

Hvis du har brug for hjælp til Perel E300GSM stil et spørgsmål nedenfor, og andre brugere vil svare dig


Måleudstyr Perel Manualer

Perel

Perel Smart Tag Manual

30 August 2024
Perel

Perel EHT-G Manual

24 August 2024
Perel

Perel E304-GN Manual

5 August 2024
Perel

Perel E305DO2 Manual

5 August 2024
Perel

Perel E305DO2-GN Manual

3 August 2024
Perel

Perel EMS111-G Manual

2 August 2024
Perel

Perel E300GSM Manual

1 August 2024
Perel

Perel EMS111 Manual

29 Juli 2024
Perel

Perel SMART1002 Manual

23 Juli 2024
Perel

Perel E305EM5-G Manual

22 Juli 2024

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

Uni-T

Uni-T UT220 Manual

3 April 2025
Uni-T

Uni-T UT681C Manual

3 April 2025
Uni-T

Uni-T UT216C Manual

3 April 2025
Uni-T

Uni-T UT611 Manual

3 April 2025
Uni-T

Uni-T UT210D Manual

3 April 2025
Uni-T

Uni-T UT210C Manual

3 April 2025
Uni-T

Uni-T UT210B Manual

3 April 2025
Uni-T

Uni-T UT682 Manual

3 April 2025
Uni-T

Uni-T UT275 Manual

3 April 2025
Uni-T

Uni-T UT08A Manual

3 April 2025