Philips L6054X1 Manual

Philips Lys L6054X1

Læs gratis den danske manual til Philips L6054X1 (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Philips L6054X1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

round

H4651

H6054

Black = Ground

Red = Low beam

White = High beam

Philips Inte lights are universal LED repla nt upgrade es with H6 054,

H4651, H4 aled beam h hts. In some cles, the ex light wiring ss

will plug di hilips Integr LED Headli s and the he ill work nor

In other v ng harnes ter may be cessary.

Here’s wh essary:

• Case 1

Your ve harness m ’s not comp the connec

termina the LED he eam Headli mpatible w ype

connect

to purch

• Case 2

Your ve s on the back

of the In arness is plugg d in.

For inst the low beam position r the

headlig ase ring harness adapters t

have an s on the er end. This will allow

to conn o the approp slot on the vehicle

harness

If you n wo (one for each head The adapters are

inexpen hing online for: Adapte harness sockets.

Pre-insta

• Put the osition.

• Discon arness s

such as to gain access to the headligh

• Next, d headlight wiring harness connector p tly onto the Philips Integral

Beam H hether it provides correct headlight ope r high beam, low beam,

and off s in the vehicle wiring harness connector line up with the electrical

connec Integral Beam LED Headlight, or if they line ut do not deliver normal

headlig need to purchase two wiring harness adapte explained above. Depending

on your erform one of the three installations shown on next page.

Installat equired:

• Tool(s ght remo ually a Phil wdriver)

• Corro tion tape

• Dielec

• Voltage tester

g tip: If the LED lights flash or flicker when y u turn them on,

apter. In some modern vehicles, ED

the h

n bulb filamen pulses are

. However, with an LED light, the nough to turn the LEDs off and

y, which results in a flashing of the light. If your LED lights flash or flicker after

ing a Philips CANbus Adapter solves this problem, and installation takes only

m Adapters can be found at many online automotive retailers.

See next page for installation s.

Installa

Installation C

conn

wiring

H4 (female) connecto

ehicle wiring harness

ess

ection

hicle

ing

ness

Vehicle wiring harness

Installatio

For a vehicle

Installatio

For a vehicle s that plugs gral Beam t but does ovide norm dlight control opera n:

Installatio

For a vehicle that does not plug directly onto the Integr eam Headlight:

1. Put the he

wiring har headlight (if not already

2. Remove th ght (procedures vary by vehicl ch online

for how-to ehicle).

3. Fill the veh s connector s h dielectric g se to seal

the conne

g the headli trols, confir he Integral B t

ates norma

eration is no nstall the Int eam Headlig he

dard headlig peration is n al, follow In low.

7. Repeat the proc r the other h t.

1. Purchase ss adapters r (female)

on one en

2. Put the he

harness fr

3. Remove th ne

for how-to

4. Fill the slo lectric grease

to seal the

5. Plug the w ntegral Beam

Headlight.

6. Put the he osition. Use the voltage

tester to d wiring harness connector

correspon

7. Put the he m on

tester to d vehicle wiring h

correspon nd ground.

the slots on wire ha onnector with dielectr ease to icle

he right).

vehicle head ight controls to confirm that the Integral Beam

Headlight operates rmally. If it does not operate normally, use the

voltage meter to rec ck the wire harness connector slots for vehicle

correct low beam, beam, and ground.

11. When correct ope is confirmed, wrap the spade / connector

connection w protection tape to protect the electrical

connection.

Headlight in place of the standard headlight.

controls to check operation.

eat the procedure for the other headlight.

1. Purchase d adapter wiring harnesses

(see Cas s page).

2. Put the he in the off position. Disconnect the vehicle wiring

harness fr ot already removed).

3. Remove o

for how-to

4. Fill the ad ness so

connector grease to seal the c

5. Plug the H he adapter wiring harness onto the Integral Beam

Headlight t

6. Plug the oth r wiring harness into the vehicle wiring

harness.

7. Use the vehicle headlight contr m

Headlight operates norm

8. Wrap the conn protection tape

to pr

9. Install the Integral Beam Headlight in pla

Retest the controls to check oper

10. Repeat the procedure fo

Black

Red = Low

White = High

Black = Ground

Red = Low beam

White = High beam

beam power and ground and the veh

have only two socket slots.

NOTE: It is commended to always wrap the connector

co ctions with corrosion protection

ta o protect the electrical connection.

Ground, Low Be es

Must us

Ground, L es

Produkt Specifikationer

Mærke:	Philips
Kategori:	Lys
Model:	L6054X1
Bredde:	324 mm
Dybde:	151 mm
Højde:	221 mm
Vægt:	2458 g
Antal pr. pakke:	1 stk
Strøm:	14 W
Pakkevægt:	2458.4706454 g
Pakkebredde:	220.98 mm
Pakkehøjde:	151.892 mm
Pakketype:	Kasse
Lampetype:	LED
Farvetemperatur:	6000 K
Indgangsspænding:	12/24 V
Pære levetid:	1500 t
Forsendelseskassens bruttovægt (indvendig):	1070.4779932 g
Mindste ordremængde:	2 stk
Påsætning af pære på køretøjer:	High beam, Low beam