Prima LPR 602 Manual


Læs gratis den danske manual til Prima LPR 602 (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Prima LPR 602, eller vil du spørge andre brugere om produktet?

Side 1/8
GB
-1-
Chart
PROGRAM SELECTION
BUTTON
Push “Programs” button
(repeatedly) until the indicator
of the required program lights
below).
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the
program. When the door is opened during a
washing cycle, the cycle is temporarily paused: the
Start indicator blinks.
To resume the cycle push the Start button and
close the door within 3 seconds.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute.
If pressed when the dishwasher is switched off it
drains any possible liquids from dishwasher (1
minute process).
If the indicator flashes repeatedly, see page 6 -
chapter ”What to do if ...”.
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
“nk_customer@whirlpool.com”.
Table of programs
Deter-
gent
Consumption
P
Programs Loading instructions
Litres kWh
Minutes
1)
1 Pre-Wash cold
Crockery to be washed later. 5.0 0.02 10
2 Glasses 40°C
Light soiling, for example glasses
and cups.
X 13.0 0.90 97
3 Quickwash 40°C
Lightly soiled crockery, with no
dried-on food.
X 13.0 0.70 30
4
Bio
2)
50°C
Normally soiled crockery.
Energy-saving program.
X 15.0 1.05 165
5 Intensive 70°C
Recommended program for heavily
soiled crockery, especially suitable
for pans and saucepans.
X 15.0 1.50 140
5019 696 01557LPR 602
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
Quick reference guide
GB
-2-
First time use
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
1.
Ask your water supply company what the
water hardness
is...
2.
...enter this value on
your dishwasher
Suggestions for detergent use
German
degrees °dH
French
degrees °fH
English
degrees °eH
Water hardness
level
3 first PROGRAM LEDs
lit on the panel
(see table of programs)
P1 P2 P3
Gel or Powder
(rinse aid and
salt)
Tablets
0 - 5 0 - 9 0 - 6.3 Soft 1
go to step 1
(see “Daily
check”)
6 - 10 10 - 18 7 - 12.6 Medium 2
11 - 15 19 - 27 13.3 - 18.9 Average 3
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4
if water is
HARD extra salt
needs to be
added
(go to step 1,
“Daily check”)
22 - 28 38 - 50 26.6 - 35 Hard 5
29 - 35 51 - 63 35.7 - 44.1 Very hard 6
36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
Water hardness should be set only
before the first wash or if water
hardness has been changed
1
Visual indicator
(depending
on the model).
Unscrew cap.
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT
NEEDS TO BE ADDED.
green: OK.
clear: NEEDS TO
BE ADDED
Daily check
Filling the salt reservoir -
Dissolve limescale (not necessary if water hardness level is set to “soft”!)
- Press and hold together Programs and buttons for minimum 3 seconds.CANCEL/Off
- Programs LEDs will indicate the water hardness setting.
- Press the
Programs
button to increase setting (when the level reaches 7, the next key press will set the level back to 1.
- Wait 30 seconds (control panel switches off) or press
START/Resume
button to save setting.
Add salt (never add detergent!)
min. 0.8 kg / max. 1 kg
Water hardness level is factory
set for medium-hard water
(level 4).
Even if you use tablets which
include salt functionality, you
must still add regeneration salt
since such detergents are not
effective enough at softening
hard water.
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
How to set water hardness in order to always assure the best cleaning results


Produkt Specifikationer

Mærke: Prima
Kategori: Opvaskemaskine
Model: LPR 602

Har du brug for hjælp?

Hvis du har brug for hjælp til Prima LPR 602 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Opvaskemaskine Prima Manualer

Prima

Prima PRDW204 Manual

11 Juli 2025
Prima

Prima LPR659A Manual

10 Juli 2025
Prima

Prima LPR661A Manual

10 Juli 2025
Prima

Prima PRD001 Manual

10 Juli 2025
Prima

Prima LPR659 Manual

25 Februar 2025
Prima

Prima LPR 602 Manual

25 Februar 2025

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer