Prima LPR9032 Manual

Prima Ovn LPR9032

Læs gratis den danske manual til Prima LPR9032 (7 sider) i kategorien Ovn. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Prima LPR9032, eller vil du spørge andre brugere om produktet?

Side 1/7
3
INSTRUCTIONS FOR USE
INSTALLATION
ELECTRICAL CONNECTION
BEFORE USING THE OVEN
SAFEGUARDING THE ENVIRONMENT
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
CARE AND CLEANING
TROUBLE-SHOOTING GUIDE
AFTER SALES SERVICE
DECLARATION OF CONFORMITY CE
4
INSTALLATION
Technical information for the installer
The oven has been designed to be installed under a worktop surface.
Do not lift the oven by the handle, but hold it by the sides.
Make sure that the appliance was not damaged during transport.
The oven and unit dimensions are shown in the below figures.
The units in contact with the oven must be heat-resistant (min. 85°C).
If the plastic laminates or the sealing material are not sufficiently heat resistant, this may result in the formation of
bubbles, deformation of the surface or detachment of the coating.
Insert the oven in the unit cavity, lifting it by the sides and being careful not to trap the power cable.
The oven and housing dimensions are illustrated in the below figures.
For correct ventilation, follow the ventilation opening directions shown in the figure 1.
Two systems can be used to fit your appliance to a chosen furniture layout:
A. Between two side panels of two distinct cabinet units without the aid of a support shelf, by fitting four support
steel brackets provided with the product. (fig. 3).
B. Between two side panels each fixed to the side of a cabinet unit without the aid of a support shelf. In this case only
the two lower support brackets will be necessary (fig. 4).
Note: In both of the above cases you must measure 717 mm from the underside of the worktop and mark the correct
position of the lower support brackets before fixing them to the sides. With reference to (fig. 3), ensure the side
support brackets are positioned 40 mm from the front of the cabinet door exterior surface, as illustrated, before
securing them to the cabinet sides. If necessary, this product can be installed in a housing unit (fig. 2). The housing unit
will not be a standard one but will have to be of a size that can accommodate the full height of the oven - minimum
height 717 mm. This housing unit will need to fulfil the ventilation requirements.
Fasten the oven using the screws.
Fig. 1
Fig. 2
Fig. 3 Fig. 4
NOTE:
Always remove
the rear panel
of the housing
unit
Top
Oven
Front of
oven
Rear
Wall
Important
BACK EDGE OF SUPPORT
SHELF (WHEN APPLICABLE)
RUNNERS
562-565
Min.
560
717
665
548
595
708
525
545
22
715
Mi
n. 560
562-565
717
5
45
548
595
525
715
22
665
708
40
600
Min. 560
717
40
665
708
525
548
5
95
22
545
715
RUNNERS
SIDE


Produkt Specifikationer

Mærke: Prima
Kategori: Ovn
Model: LPR9032

Har du brug for hjælp?

Hvis du har brug for hjælp til Prima LPR9032 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ovn Prima Manualer

Prima

Prima PRSO301 Manual

10 Juli 2025
Prima

Prima PRD Manual

25 Februar 2025
Prima

Prima LPR9032 Manual

25 Februar 2025
Prima

Prima LPR9034 Manual

25 Februar 2025
Prima

Prima LPR9030 Manual

25 Februar 2025
Prima

Prima LPR9028 Manual

25 Februar 2025
Prima

Prima LPR9026 Manual

25 Februar 2025
Prima

Prima LPR9024 Manual

25 Februar 2025
Prima

Prima LPR9023 Manual

25 Februar 2025
Prima

Prima LPR9022 Manual

25 Februar 2025

Ovn Manualer

Nyeste Ovn Manualer