Princeton Tec Switch MPLS Manual

Princeton Tec Ikke kategoriseret Switch MPLS

Læs gratis den danske manual til Princeton Tec Switch MPLS (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Princeton Tec Switch MPLS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Battery installation

1. ARC Rail Installation 2. MOLLE Mount

Slide ARC Rail Adapter into ARC rail to desired position and secure in place with center

anti-slip lock screw. DO NOT OVERTIGHTEN this screw.

Slide clip inside any strap position, pinch MOLLE strap to hook the lower end of the

metal clip onto the strap.

3. MICH Mount Installation 4. Picatinny Rail Mount

Back the screw out so the end of screw is ush with metal U-clip. Slide the exposed

U-clip over the bottom edge of your helmet with the metal clip on the inside and the

plastic base exposed on the outside of your Helmet. Holding Mount rmly upward,

tighten center slotted screw until it stops.

Remove the center through screw from the side of the Picatinny base mount. Slide Pica-

tinny to desired position and insert side locking screw aligning with any slot in Picatinny

rail and tighten to clamp in place. DO NOT OVERTIGHTEN this screw.

5. (ABR) Above Rail Mount

A. If using MPLS ABR on a ballistic helmet, skip to step two. For

use with nonballistic helmets, begin by snapping off unneeded

portion of ABR mount by hand or with a pair of pliers, and

discarding the smaller ‘hook’ portion

Loosen or remove front rail screw, and slide ABR into desired position

beneath rail. Retighten front rail screw.

1a 2a 1b 2b 3b 4b

Select Charge MPLS mount and secure with included machine screws, gently tightening with a Phillips screwdriver. Install Switch/Point onto mount.

1c 2c 3c

POINT / SWITCH

M P L S

MODULAR PERSONAL

LIGHTING SYSTEM

OPERATING AND MAINTENANCE

INSTRUCTIONS

English

Battery Installation

White, Blue or Green LED

• (2) CR2016 Coin Cells - 6V

• Infrared and Red LED

• (1) CR2032 Coin Cell - 3V

Princeton Tec cares about the environment and recom-

mends recycling batteries. For more information about

battery recycling, please go to: batteryrecycling.com To

install the batteries, rotate light unit out of base. Lift tab

of battery door on the underside of light unit to expose

coin cell(s)

Install coin cell(s) batteries with the (+) positive side fac-

ing up. Improper installation of the batteries will damage

the light and void the warranty.

Replace the battery door with the lift tab properly

aligned with lift tab slot of the housing. Press door rmly

in place making sure it is all the way seated in place.

WARNING !

Never mix fresh and used batteries.Never mix different

battery brands or chemistry types.

Always remove drained batteries immediately.

Remove batteries during long periods of storage.

Switch Operation

Modes-Low, High (Color), High (White or Red)

Low, High (Color): Select by pressing and releasing the

button within 1.6 seconds of the previous button press.

High (White or Red): Hold down the push button in any

mode for 1.6 seconds to activate the high output light

mode. Once off, the Switch will always return to the low

(color) LED mode once turned on again.

There are two ways to turn the Switch-MPLS off.

1. You can cycle through the modes within 1.6 seconds of

the initial button press until you reach the off mode.

2. Or if more than 1.6 seconds has passed since the

previous button press, the next press of the button will

turn the light off.

Troubleshooting

If the MPLS fails to light:

• Check the batteries for proper installation.

• Replace batteries if proper installation is conrmed.

• This light has been designed to be water resistant.

Check the light for water contamination on the circuit

board. The light will resume normal operation once any

water is shaken or blown out and the light is left open

until completely dry. If the light has been contaminated

with salt water, ush the unit with fresh water and dry

as described above.

USA– International 1-Year Warranty

WARRANTY – Princeton Tec warrants this product to be

free from defects in workmanship and materials under

normal use for one year. This warranty covers all of the

component parts of the product except batteries. This

warranty does not cover deterioration due to normal

wear or damage due to misuse, alteration, negligence,

accidents, or unauthorized repair. Princeton Tec will

repair or replace parts which are

defective in workmanship or materials. Your authorized

Princeton Tec Dealer and Princeton Tec are the only

facilities authorized to repair the product. After (3) un-

successful attempts (within the warranty

period) to repair the product, you have the right to elect

replacement of the product or a refund of the purchase

price less allowance for use of the product. NO IN-

CIDENTAL OR CONSEQUENTIAL DAMAGES ARE

INCLUDED IN THIS WARRANTY. (Some states do not

allow the exclusion or limitation of incidental or conse-

quential damages, so the above limitations or exclu-

sions may not apply to you.) This warranty gives you

specic legal rights, and you may also have other rights

which vary from state to state.

Princeton Tec reserves the right to change product

specications without notice.

FOR CALIFORNIA RESIDENTS

WARNING: This product contains Bisphenol A (BpA) a

chemical known to the State of California to cause birth

defects or other reproductive harm.

Return Policy

If your light fails to operate, follow these simple steps:

1. Check batteries. Replace if necessary.

2. To send your light in for repair or replacement, rst

contact Princeton Tec customer service on

1-800-257-9080 to request an RMA number. Please

have your light model, date of purchase and a brief

description of the fault your are experiencing. No

warranty repairs will be accepted without an RMA

number.

3. Return the light to: Princeton Tec, PO Box 8057

Trenton NJ 08650. Postage due and freight collect

items will not be accepted.

4. Upon receipt your light will be processed in about

two weeks. Please allow additional time for return

transportation from NJ.

Princeton Tec

PO Box 8057, Trenton, NJ 08650

Phone: 609-298-9331

Fax: 609-298-9601

princetontec.com

Produkt Specifikationer

Mærke:	Princeton Tec
Kategori:	Ikke kategoriseret
Model:	Switch MPLS

Har du brug for hjælp?

Hvis du har brug for hjælp til Princeton Tec Switch MPLS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Princeton Tec Manualer

Princeton Tec MPLS-ABR Manual

25 Februar 2025

Princeton Tec Switch MPLS Manual

25 Februar 2025

Princeton Tec Charge X Manual

7 December 2024

Princeton Tec Charge Pro Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tams Elektronik Heißwolf SFR-4000 Manual

15 September 2025

Fulgor Milano FSRC 3004 P MI ED 2F Manual

15 September 2025

Panasonic SD3-A1 Manual

15 September 2025

Biltema 30-057 Manual

15 September 2025

Solplanet ASW3680-S-G2 Manual

15 September 2025

Bretford MDMLAP20NR Manual

15 September 2025

Timbersled RIOT 120 Premium (2024) Manual

15 September 2025

Timbersled 120 SX (2022) Manual

15 September 2025

Brandson 303824 Manual

15 September 2025

Roccat Recon Cloud Manual

15 September 2025