Pryme BT-522s-V2 Manual

Pryme Ikke kategoriseret BT-522s-V2

Læs gratis den danske manual til Pryme BT-522s-V2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Pryme BT-522s-V2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

This manual applies to all

PRYMEBLU BT-500 series

adapters for radios with

SINGLE or DUAL PIN

accessory connectors.

3 4

Controls and Connection

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment oﬀ and on, the user is encouraged to

try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit diﬀerent from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user's authority to operate this

equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. To maintain compliance with FCC RF exposure

compliance requirements, please avoid direct contact to the transmitting antenna

during transmitting.

RF Exposure Warning!

Please keep product 20cm away from your

body or bystander during the radio operation.

The typical handheld radios were

certiﬁed under mobile usage condition

(i.e. keep 20cm away from the user body)

and use of such radio closer than 20cm may

exceed the US RF exposure limit

and shall be avoided.

Version 2.1.S February 2021

911 Mariner St., Brea, CA 92821

PH: 714.257.0300 FAX: 714.257.0600

TOLL FREE: 800.666.2654

WWW.PRYME.COM

Wireless Adapter

Model No.: BT-500-Simple-Pin

Made in Taiwan

FCC ID: N2E-BTM01

The PRYMEBLU Adapter allows you to use a compatible wireless

headset or other audio accessory with your 2-way radio.

PRYMEBLU ADAPTER USER’S GUIDE

For Portable Radios with SIMPLE PIN accessory connector

PRYME® and PRYMEBLU® are trademarks owned by PRYME Radio Products,

Brea CA. All other product or service names are the property of their respective owners.

STEP ONE: Charging the PRYMEBLU Adapter

The PRYMEBLU Adapter has an internal Lithium Ion rechargeable battery pack which must be charged prior to operation, and must be

recharged regularly. A fully charged battery will provide approximately 10 hours (or more) of operation before needing to be recharged,

however, operating time can vary depending on usage and the condition of the battery pack. Recharge the battery regularly.

To charge the PRYMEBLU Adapter:

1. Ensure the PRYMEBLU Adapter is turned oﬀ, using the switch located on the back of the device.

2. Plug the supplied wall charger into a standard 120 volt AC outlet.

3. Plug the charger into the charge jack on the bottom of the PRYMEBLU Adapter. You will need to remove the protective rubber cover that

is inserted into the charge jack. (To prevent dust and moisture from damaging your adapter, always ensure this cover is in place when you

are not charging the adapter.)

4. Once the charging process has begun, the LED indicator on the top of the PRYMEBLU Adapter will show a constant blue light. Typical

charge time is approximately 5-6 hours. Actual charge time will vary depending on several factors including the battery’s charge state,

condition, and age.

6. Disconnect the charger from the adapter when charging is completed.

Charging Cautions:

- Use only the wall charger supplied by the manufacturer. Do not use any other charger.

- Do not use a wall charger that appears to be damaged. (Example: frayed wires, melted plastic, etc.)

Contact PRYME to get a new manufacturer-approved replacement charger.

- Do not tamper with or modify the PRYMEBLU Adapter or charger.

-Always turn the power switch to the oﬀ position when charging the PRYMEBLU Adapter.

Connecting the Adapter to RadioCharging the PRYMEBLU Adapter

STEP TWO: Connecting to a 2-way Radio

To connect your PRYMEBLU Adapter to a 2-way radio, follow these steps:

* Always turn oﬀ your 2-way radio before connecting the PRYMEBLU Adapter.

* Plug the PRYMEBLU adapter’s radio connector into the speaker-microphone / audio accessory jack of your 2-way radio.

* You can attach the PRYMEBLU Adapter to your 2-way radio or clothing using the Velcro fastener.

QUICK START

1. Connect the PRYMEBLU adapter to a compatible 2-way radio.

2. Pair the PRYMEBLU adapter with a compatible wireless audio accessory.

3. Test and use.

Multifunction Talk Switch

Used to place the PRYMEBLU

Adapter in pairing mode.

Once paired with an audio

accessory, this switch is used

to activate the Push-To-Talk

function of the 2-way radio

Status LED

The LED ﬂashes messages that

let the user know the current

status of the PRYMEBLU Adapter

Velcro Fastener

or Belt Clip

Used to attach

the PRYMEBLU

adapter to the

2-way radio

or to the user’s

belt or lapel

Radio Connector

Plugs into the 2-way

radio’s Mic/Speaker jack.

Belt Clip Version

Velcro Fastener

Version

Produkt Specifikationer

Mærke:	Pryme
Kategori:	Ikke kategoriseret
Model:	BT-522s-V2

Har du brug for hjælp?

Hvis du har brug for hjælp til Pryme BT-522s-V2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Pryme Manualer

Pryme BLU BT-500-M11-V2 Manual

6 November 2025

Pryme PICO-USBC-BF Manual

13 August 2025

Pryme BT-522s-V2 Manual

13 August 2025

Pryme LNK-01-ZU Manual

13 August 2025

Pryme PICO-LIGHTNING-EH Manual

12 August 2025

Pryme BLU BT-523-V2 Manual

30 Juni 2025

Pryme BTH-900-MAX Manual

4 Juni 2025

Pryme BT-583APX-V2 Manual

3 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Siemens WQ32G28IL Manual

6 December 2025

MDT BE-TA550606.02 Manual

6 December 2025

Opticis USC-CC32 Manual

6 December 2025

Audio-Technica AT33xMONO Manual

6 December 2025

Bosch SPI4EMS24E Manual

6 December 2025

Fostex P1000K Manual

6 December 2025

Advantech UTC-124I1 Manual

6 December 2025

Anton/Bauer Titon Micro Kit Manual

6 December 2025

Philips Zoom! DayWhite DIS130 Manual

6 December 2025

Opticis USB-FC30AA Manual

6 December 2025