Pyle PHCT55 Manual

Pyle Kabler til computere og periferiudstyr PHCT55

Læs gratis den danske manual til Pyle PHCT55 (1 sider) i kategorien Kabler til computere og periferiudstyr. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Pyle PHCT55, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
PHCT55
CABLE
TRACKER
INTRODUCTION
This Cable
Tr
acker is designed
to
identify and trace
wires
or
cables within a group without damaging the
insulation.
For
telephone line, it can identify
some
states
in the line. Owning this instrument, it is more convenient
to install, debug, and maintain telephone line, There
are
a
Sender
and a . Receiver included in the Cable Tracker
FUNCTIONS
1.
Judge continuity
of
the cables
or
wires.
2. Track the cables
or
wires, and diagnose the break
point.
3.
Receive the tone signal
on
the cables
or
wires
( telephone line
).
IDENTIFY
THE
STATE
OF
WORKING
TELEPHONE
LINE
USE
SENDER
( SWITCH
TO
"
OFF"
)
1. : Identify TIP&RING
Connect the red test lead to the side
of
one line and
the the black test lead to side
of
another line.
a.
"CO NT" indicator light is "green" w hen you connect
the the red test lead to Ring ( - ) side.
b.
"CO
NT
" indicator light is "red" when you connect
the red test lead to the TIP (+)
side.
2. Identify
CLEAR
, , RINGING
BUSY
state on th e
working telephone line:
Connect the the red test lead to RING side, black
test lead to , the TIP side
or
connect
RJll
into the
RJll
socket on telephone.
a.
"CONT"
indicator light is "green", indicates a
CLEAR
line.
If
"CO
NT" indicator light is "red" ,
it
means
the polarities we re reversed.
4.
Identify the state in the working telephone line (clear,
ring, busy)
5. a Send single solid tone
or
dual alternating tone to the
object cables
or
wires .
STRUCTURE
tip button battery cover earphone jack
J
Receiver
test lead
switch -
Sender
b. "CO NT" indicator does not
glow
or
glow faintly,
indicates a Y BUS line.
c.
"CONT"
indicator light brightly
ni
ckering "YELLOW",
indicates a RINGING
li
ne. ( to Switch "CONT" will
terminate the
calion
the
line)
BATTERY
REPLACEMENT
1.
Sender
Battery replacement:
Remove the
screw
on the the back case, remove
back case, replace the a exhausted battery with
new
one
of
9V(6F22). Rejoin the the back case and install
screw.
2. Recei ver Battery replacement:
Remove the scr
ew
on
the battery compartment,
remove the battery cover, replace the exhausted
battery with a
new
one
of
9V(6F22). Rejoin the r cove
and install the
screw
.
OPERATION
INSTRUCTION
TEST
CONTINUITY
1. Use the
Sender
( switch to "CONT")
Connect the the test leads to object pair, use
"CO
NT"
postion.The bright green
of
"CONT"
indicates the
co
ntinuity.(line r ises tance not exceeding
10kO.)
2.
Use the Sender (switch to "TONE")
a.
Connect the test le
ads
to
a pair
of
cables, touch
Receiver to the cables.
If
the two cables give larger
and same tones, it means both
of
them h
ave
continuity. Otherwise which the cable gives lower
tone doesn't have continuit
y.
b.
Connect one test lead to one cable a among group
of , cables connect another test lead and the other
cables to earth ground. Touch the tip
of
Receiver to
another end
of
the cable mentioned above.
Reception
of
tone
means
that the cable has
continuity. ( see
figure)
NOTE
1.
If
you don't use the Cable Tracker, set the switches to
"OFF".
If
you don't use the Cable Tracker for a
long time, . take out all the batteries
2 Keep away from moisture.
3.
Do not use Cable Tra
cker
under high voltage
environment.
4. Always follow thi s u y sers manual. Otherwise it ma
cause the the damage to tester
or
personal injury.
DISPOSAL
OF
THIS
ARTICLE
Dear Customer,
1!
Please help a
....
oiding refuse.
If you at some point intend to dispose of
this article, then please keep in mind that
many
of its components consist
of
valuable materials, . which can be recycled
Please do not discharge it in the garbage
bin, but check with your local council for
recycling facilities
in
you r area.
NOTE
Don't connect to any active AC
or
DC circuit
for measuring continuity.
TRACK
CABLE
OR
WIRES
USE
SENDER
(SWITCH
TO
"TON E") D AN RECEIVER
Connect the s , test lead to the pair
or
attach one test lead
to ground and another test lead to eilher side of the line.
Move the Receiver close to and a ( long the pair
or
the
line ). Reception
of
the . tone indicates the track
NOTE
Do not connect to
any
active c s ircuit in thi
mode
.
www PyleAudio com

Produkt Specifikationer

Mærke: Pyle
Kategori: Kabler til computere og periferiudstyr
Model: PHCT55

Har du brug for hjælp?

Hvis du har brug for hjælp til Pyle PHCT55 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Kabler til computere og periferiudstyr Pyle Manualer

Pyle

Pyle PHCT45 Manual

4 Marts 2024
Pyle

Pyle PPJX50 Manual

2 Marts 2024
Pyle

Pyle PHCT55 Manual

5 December 2022

Kabler til computere og periferiudstyr Manualer

Nyeste Kabler til computere og periferiudstyr Manualer

Hosa

Hosa Edge CMK-010AU Manual

3 November 2025
gofanco

gofanco HDbitT8Pv2 Manual

3 November 2025
gofanco

gofanco HD20Ext-Cas Manual

2 November 2025
Griffin

Griffin LG-AP3614 Manual

2 November 2025
Orei

Orei ARC-EX300-K Manual

2 November 2025
Kramer

Kramer CLS-AOCH/XL-262 Manual

16 Oktober 2025
Ewent

Ewent EW-110202-020-N-P Manual

11 Oktober 2025
Fresh 'n Rebel

Fresh 'n Rebel 2LC120BL Manual

11 Oktober 2025
Repotec

Repotec RP-1703 Manual

9 Oktober 2025
IOPLEE

IOPLEE IOPEXTHE4IN1603 Manual

7 Oktober 2025