QSC AD-S402T Manual

QSC Højttaler AD-S402T

Læs gratis den danske manual til QSC AD-S402T (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 2 anmeldelser. Har du et spørgsmål om QSC AD-S402T, eller vil du spørge andre brugere om produktet?

Side 1/4
1
TD-001597-01-A
AD-S402T
Quick Start Guide
NOTE:
The AD-S402T is UL listed (1480A) for indoor use only
Installation
AD-S402T passive column loudspeaker systems require amplified audio signals. A pass-through on each loudspeaker permits connection to multiple loudspeakers.
The pluggable “Eurostyle” connectors allow the installer to pre-wire the audio system on site before the loudspeakers are installed.
TD-001597-01-A
*TD-001597-01*
The loudspeaker comes with a weather cover for the input cup to protect the input connections and switches from
precipitation and other weather hazards (Figure 1). Use the weather cover for all non-UL outdoor installations or any
applications where the loudspeaker may be exposed to moisture. To ensure a good seal in the cable gland, use outdoor-rated
cable with a round jacket between 5.5 mm and 9.4 mm in diameter.
To use the weather cover:
1. Loosen the nut on the cable gland.
2. Pass the cable all the way through the nut and the rest of the gland.
3. Attach the input connector to the wires (see
Input Connector
, below).
4. Once the loudspeaker enclosure is installed, plug the input connector into the loudspeaker's input cup. Secure the
connector to the loudspeaker using the two captive retaining screws, one on each end.
5. Make sure that the transformer tap selection switch is set properly.
6. Place the cover onto the loudspeaker's input cup and attach it using the four screws, lock washers, and flat washers
provided.
7. Dress the cable so there is no undue strain on it. Tighten the gland nut until the grommet inside the gland has made a
tight seal onto the cable jacket.
Input Connector
AD-S402T Weather Cover
Diameter
up to
0.37 in
9.4 mm
— Figure 1 –
Strip wire
¼in
6.3 mm
Up to
10 AWG
6 mm²
Turn screw fully
counterclockwise.
Insert wire fully.
Turn screw clockwise
to clamp wire tightly.
— Figure 2 –
INPUT
THRU
To other
loudspeaker(s),
if necessary
— Figure 3 –
The pluggable “Eurostyle” input connector (Figure 2) has four terminals to facilitate connection on a distributed
line. It also allows the installer to pre-wire the venue before the loudspeakers themselves are installed. The
connector accommodates wire up to 10 AWG or 6 mm
2
. Be sure of proper and consistent polarity at each connector
(Figure 3). If one or more loudspeakers is out of polarity with others, the acoustic performance will suffer. Always
secure the connector to the loudspeaker using the retaining screws at both ends.
Mounting
Tilt/Swivel Bracket
The bracket provided with the loudspeaker allows 0, 5,
10, 15, and 20 degrees of downward tilt (Figure 4), and
up to ±55 degrees of horizontal panning (Figure 5).
These angles may be constrained by the loudspeaker
enclosure and adjacent walls or other structural elements.
In addition, the bracket can be inverted, which allows the
loudspeaker to be tilted up.
— Figure 4 –
120 degrees pan
at 0 degrees tilt
— Figure 5 –


Produkt Specifikationer

Mærke: QSC
Kategori: Højttaler
Model: AD-S402T
Kode for international beskyttelse (IP): IP54
Bredde: 131.3 mm
Dybde: 327.5 mm
Højde: 126.1 mm
Vægt: 3400 g
Produktfarve: Hvid
Pakkevægt: 5000 g
Pakkedybde: 544 mm
Pakkebredde: 310 mm
Pakkehøjde: 244 mm
Udgangseffekt (RMS): 60 W
Driftstemperatur (T-T): -20 - 50 °C
Husmateriale: Aluminium
Anbefalet brug: Hjem
Frekvensområde: 110 - 20000 Hz
Lydtryksniveau (maks.): 111 dB
Impedens: 16 ohm (Ω)
Forbindelsesteknologi: Ledningsført
Højttaler, type: Fuld interval
Lyd-output kanaler: - kanaler
Højttaler, placering: Surface-mountable, Wall-mountable
Certificering: EASE, CLF, CAD, BIM
Bæredygtighedscertifikater: RoHS
Antal drivere: 4
Driver diameter: 69.8 mm
Sensitivitet: 85 dB
Overholdelse af bæredygtighed: Ja
Bashøjttaler: Ja
Antal bashøjttalerdrev: 4
Monteringsbeslag inkluderet: Ja
Anbefalet forstærkereffekt (maks.): 120 W

Har du brug for hjælp?

Hvis du har brug for hjælp til QSC AD-S402T stil et spørgsmål nedenfor, og andre brugere vil svare dig




Højttaler QSC Manualer

QSC

QSC SC-423C Manual

11 September 2025
QSC

QSC AD-S82 Manual

11 September 2025
QSC

QSC AC-C8T Manual

11 September 2025
QSC

QSC NL-P4 Manual

11 September 2025
QSC

QSC SC-223 Manual

11 September 2025
QSC

QSC AD-S12 Manual

11 September 2025
QSC

QSC I-282H Manual

11 September 2025
QSC

QSC AD-DWL.BASE Manual

11 September 2025
QSC

QSC AC-C4T Manual

11 September 2025

Højttaler Manualer

Nyeste Højttaler Manualer

RetroSound

RetroSound R-507N Manual

29 Oktober 2025
TDK

TDK TP6803BLK Manual

28 Oktober 2025
TDK

TDK TREK Flex A28 Manual

28 Oktober 2025
Vonyx

Vonyx VX822 Manual

21 Oktober 2025
Memphis Audio

Memphis Audio SRX42 Manual

19 Oktober 2025
Memphis Audio

Memphis Audio MS62 Manual

19 Oktober 2025
Goji

Goji Mini GMINIG17 Manual

19 Oktober 2025
Audison

Audison VOCE AV 12 Manual

19 Oktober 2025