Rane BB 44X Manual

Rane Ikke kategoriseret BB 44X

Læs gratis den danske manual til Rane BB 44X (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Rane BB 44X, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

BB 44X / OPTION 88 OPERATORS MANUAL

Application Information

Driving Impedances

Some people wrongly feel you cannot use a transformer to con-

vert between -10 dBV and +4 dBu because of low impedances.

is is not a problem as long as you use them to interconnect

equipment with at least 15 kΩ input impedance. Since most

professional products have input impedances of 20 kΩ or greater

(50k and 100 kΩ are not uncommon), this should never be di-

cult. A 15 kΩ load winds up looking like 1 kΩ to the equipment

with the -10 dBV output (due to transformer action). is may

seem excessively low, but is not in practice. e maximum trans-

former output level of +24 dBu occurs with an input level of +10

dBV, which equals 3.16 volts. And 3.16 volts driving 1 kΩ only

requires 3.16 milliamps, which is a very modest requirement for

any -10 dBV equipment to deliver.

Wiring

e BB 44X follows AES/ANSI/IEC standards of pin 2 positive

and pin 3 negative. Note the shields (commons) of the RCA

jacks are tied for the Inputs and the Outputs but not to each oth-

er. is allows ground isolation of stereo Input and Output pairs.

A positive signal applied to pin 2 of the 3-pin connectors causes

a positive signal to appear on the tip of the associated RCA jacks,

and vice-versa.

Signal Direction

Signal can be converted through the channels either direction.

at means there is the possibility of having 4 channels -10 dBV

unbalanced to +4 dBu balanced, or vice versa (in the standard

unit). e only problem arises in the gender of the XLR con-

nector. e solution requires same-sex XLR adaptors or special

cables.

Chassis Grounding

A tapped hole and a #6-32 screw is provided for chassis ground-

ing purposes. Good practice dictates earth-grounding the BB

44X. If the grounding integrity of the rack screws is in doubt,

run a wire from this screw to a known earth ground.

Expansion Assembly

e OPT 88 (Option 88) expands the BB 44X into an eight

channel model. e OPT 88 consists of a printed circuit board

with four additional transformers and jacks soldered in place.

e OPT 88 installs easily in the blank side of the BB 44X.

Assembly is simple: remove the cover, install the board in place,

and secure with the supplied mounting screws. No soldering

required; all you need are #1 and #2 Phillips screwdrivers. See

the illustration on the next page.

e OPT 88 may be used in some environments without the

BB 44X, however best RFI rejection is obtained using the cold

rolled steel metal chassis of the BB 44X.

INPUT 1

OUTPUT 1

11 4

+4 dBu -10 dBV

11 4

INPUT 2

+4 dBu

9 2

-10 dBV

OUTPUT 2

114

OUTPUT 3

+4 dBu

-10 dBV

INPUT 3

114

OUTPUT 4

+4 dBu

-10 dBV

INPUT 4

All features & specications subject to change without notice 12275

©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5000 TEL 425-355-6000 FAX 425-347-7757 WEB rane.com

BALANCED

UNBALANCED

2 4

BALANCED

1 3

BALANCED

UNBALANCED

6 8

BALANCED

5 7

M2.9 X 5/16" SCREW (9 PLACES)

6-32 X 3/16" SCREW (2 PLACES)

INSTALLATION INSTRUCTIONS:

1. REMOVE THE (7) TOP COVER SCREWS.

2. REMOVE TOP COVER.

3. INSTALL PCB ASSEMBLY INTO CHASSIS.

4. INSTALL THE (11) REAR PANEL SCREWS.

5. INSTALL THE (2) BOTTOM SCREWS.

6. REPLACE TOP COVER.

7. REPLACE THE (7) TOP COVER SCREWS.

8. PLUG AND PLAY.

PCB ASSEMBLY

H:\BB44\105185.DWG

4-40 X 1/4" SCREW (2 PLACES)

(9) M2.9 X 5/16" AND (2) 4-40 X 1/4"

BB 44X

4321

RANE CORP.

ACN001.187.837

PIN 2

BALANCED WIRING:

PIN 1

PIN 3

CHASSIS GROUND

NEGATIVE

POSITIVE

INPUTS

+4dBu

OUT

-10dBV

OUTPUTS

+4dBu

INPUTS

+4dBu

OUT

-10dBV

OUTPUTS

+4dBu

WARNING: is product may contain chemicals

known to the State of California to cause cancer,

or birth defects or other reproductive harm.

Parameter LimitSpecication Units Conditions/Comments

Transformer Construction Nickel Core Bobbin Wound Grade “80” Ni

Turns Ratio -10 dBV (316 mV): +4 dBu (1.23 V)1:3.89

Maximum Levels (In or Out )

..........-10 dBV +10 (40 Hz-20 kHz); +4.5 (20 Hz) 1% THD point0.5dB dBV

..........+4 dBu +24 (40 Hz-20 kHz); +18.5 (20 Hz) 1% THD point0.5dB dBu

Input Impedance (Load impedances as shown)

..........-10 dBV 1k 5 % Ω Load impedance 15 kΩ

..........+4 dBu 15k 5 % Ω Load impedance 1 kΩ

Insertion Loss 0.5 0.1 dB With recommended load impedance

DC Resistance 47.5 / 200 Ω -10 dBV / +4 dBu10%

Frequency Response 20 Hz -20 kHz +4 dBu In or Out; rec. load impedance±2 dB

THD + Noise less than .05 (40 Hz-20 kHz) % +4 dBu In or Outmax

Unit: Conformity CE, FCC Exempt

..........Size 1.75"H x 19"W x 5.3"D (1U) (4.4 cm x 48.3 cm x 13.3 cm)

..........Weight 4 lb (3 kg)

Shipping: Size 4.25" x 20.3" x 13.75" (11 cm x 52 cm x 35 cm)

..........Weight (5 kg)8 lb

All specications apply both directions, unless noted. 0 dBu = 0.775 volts; 0 dBV=1.0 volts

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	BB 44X

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane BB 44X stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025

AMX DVX-2250HD Manual

14 September 2025

AMX Vision² Manual

14 September 2025

AMX NMX-ENC-1100 Manual

14 September 2025

AMX UPC20+ Manual

14 September 2025