Schneider MTN644692 Manual

Schneider Ikke kategoriseret MTN644692

Læs gratis den danske manual til Schneider MTN644692 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Schneider MTN644692, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

The binary input REG-K/8x230 is used to connect eight

conventional 230 V devices (e.g. movement detectors,

light-sensitive switches) to the bus system.

The binary input has a bus coupler. It is installed on a

DIN rail acc. to EN 60715, with the bus connection

made via a bus connecting terminal. A data rail is not

required.

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connecting and establishing KNX networks

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• The internal device connection of the potentials is not

suitable for carrying load currents.

• Only operate the device according to the specifica-

tions stated in the Technical data.

• All the devices that are installed next to the binary in-

put must be equipped with basic insulation at the very

least.

Failure to follow these instruction can result in

equipment damage.

Binary input introduction

ACover of the bus connecting terminal

BProgramming button/programming LED

COperational LED

DChannel status LEDs

1Set the binary input onto the DIN rail.

2Connect KNX.

WARNING

Risk of fatal injury from electrical current.

The device could be damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX line.

½CAUTION

The device could be damaged.

High voltages can cause damage. Never connect

devices with more than 230 V.

Operating and display elements

Installing the binary input

RUNE 8E 7E 6E 5E 4E 3E 2E 1

E1 N N E2 E3 N N E4

E5 N N E6 E7 N N E8

5 mm

1 2

3 4

230 V

4 mm

KNX

3Connect the input cables.

|The N conductors must be connected to the

device. Inputs E1 to E4 have a common potential

(4 x N, top row) and inputs E5 to E8 have a

common potential (4 x N, bottom row). Inputs E1

to E4 and E5 to E8 can be assigned to each other

with different phases.

1Press the programming button.

The programming LED lights up.

2Load the physical address and the application into

the device from the ETS.

The operating LED lights up: The application was loaded

successfully, the device is ready for operation.

Schneider Electric Industries SAS

35 rue Joseph Monier

Rueil Malmaison 92500

France

If you have technical questions, please contact the Cus-

tomer Care Centre in your country.

se.com/contact

Putting the binary input into operation

Technical data

Power supply from

bus: DC 24 V / max.18 mA

Insulation voltage: AC 4 kV bus/inputs

Inputs

Nominal voltage: AC 230 V ±10 %, 50/60 Hz

0 signal: <40 V

1 signal: >160 V

Nominal current: AC approx. 7 mA

Permitted cable

length: max. 100 m/channel

Ambient temperature

Operation: -5 °C to +45 °C

Storage: -25 °C to +55 °C

Transport: -25 °C to +70 °C

Max. humidity: 93 % relative humidity, no

moisture condensation

Environment: The device is designed for use

at a height of up to 2000 m

above sea level (MSL).

Connections

Inputs, outputs: Screw terminals

Single-core: 1.5 mm2 to 2.5 mm2

Finely stranded

(with core end sleeve): 1.5 mm2 to 2.5 mm2

Bus: Bus connecting terminal

Dimensions

Height x width x

depth: 90 x 72 x 65 mm

Device width: 4 modules

Schneider Electric -Contact

KNX

+ -

L3 NL1 L2

Schneider Electric Limited

Telford, TF3 3 BL, UK

UK Representative

Stafford Park 5

SpaceLogic KNX Binary input REG-K/8x230

Operating instructions

Art. no. MTN644692

RUNE 8E 7E 6E 5E 4E 3E 2E 1

V6446-562-01 11/21

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN644692

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN644692 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider BC650-RSX761 Manual

7 Oktober 2025

Schneider P8VNTG Manual

1 Oktober 2025

Schneider QCGK3 Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3319 Manual

1 Oktober 2025

Schneider Altivar 312 VZ3V3103 Manual

1 Oktober 2025

Schneider SCTK30 Manual

1 Oktober 2025

Schneider Altivar 71 VW3A7201 Manual

1 Oktober 2025

Schneider OHBS Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3502 Manual

1 Oktober 2025

Schneider Altivar 21 VW3A21101 Manual

1 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hendi 580035 Manual

3 November 2025

MSW -PTM-02 Manual

3 November 2025

ANCEL FX1000 Manual

3 November 2025

Extron RCP 401 Manual

3 November 2025

IFM E11847 Manual

3 November 2025

Ingenuity Easy Rinse Bather Manual

3 November 2025

ANCEL S2000 Manual

3 November 2025

ANCEL HD3600 Manual

3 November 2025

Hendi 550113 Manual

3 November 2025

Philips Series 5000 MG5942 Manual

3 November 2025