Schneider MTN646991 Manual

Schneider Ikke kategoriseret MTN646991

Læs gratis den danske manual til Schneider MTN646991 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Schneider MTN646991, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

The control unit 0-10 V REG-K/3-gang with manual

mode dims and switches fluorescent lamps using

electronic ballasts with a 0-10 V/1-10 V interface and LV

halogen lamps using transformers with a 0-10 V/1-10 V

interface.

|The control voltage range can be set with the

ETS via a parameter.

You can also manually switch the connected loads with

the manual switches on the control unit without bus

voltage.

The control unit has a bus coupler. It is installed on a

DIN rail acc. to EN 60715, with the bus connection

made via a bus connecting terminal. A data rail is not

required.

For your safety

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR

ARC FLASH

Safe electrical installation must be carried out only by

skilled professionals. Skilled professionals must prove

profound knowledge in the following areas:

• Connecting to installation networks

• Connecting several electrical devices

• Laying electric cables

• Connecting and establishing KNX networks

• Safety standards, local wiring rules and regulations

Failure to follow these instructions will result in

death or serious injury.

The device may be damaged!

• Only operate the device according to the specifica-

tions stated in the Technical data.

• All the devices that are installed next to the binary in-

put must be equipped with basic insulation at the very

least.

Failure to follow these instruction can result in

equipment damage.

Control unit introduction

ABus connecting terminal

BCable cover

CProgramming button

DProgramming LED (red)

EOperating LED "RUN" (green)

FManual switch

GChannel terminals for load voltage

HOutputs 1-10 V

1Set the control unit onto the DIN rail.

2Connect KNX.

¼WARNING

Risk of fatal injury from electrical current. The

device could become damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX line.

½WARNING

Risk of fatal injury from electrical current. The

device could become damaged.

Disconnect the mains voltage before connecting

the device to the load.

Terminals may not be inserted under load.

Connections, displays and operating

elements

Installing the control unit

1 2 3

5 mm

1 2

3 4

230 V

4 mm

KNX

3Connect the bus voltage.

4Connect the load.

5Connect the load voltage.

1Press the programming button.

The programming LED lights up.

2Load the physical address and application into the

device from the ETS.

The programming LED goes out.

The operating LED lights up: The application was loaded

successfully, the device is ready for operation.

AControl unit

BElectronic ballast with 0-10 V/1-10 V interface

CFluorescent lamp

DElectronic transformer with 0-10 V/1-10 V

control input

ELV halogen lamps

FTo other devices with 0-10 V/1-10 V interface

Putting the actuator into operation

KNX

+ -

NL1

0-10V

12V AC

0-10V

16 A

SpaceLogic KNX Control unit 0-10 V REG-K/

3-gang with manual mode

Operating instructions

Art. no. MTN646991

123

V6469-562-01 11/21

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Ikke kategoriseret
Model:	MTN646991

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN646991 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Schneider Manualer

Schneider BC650-RSX761 Manual

7 Oktober 2025

Schneider P8VNTG Manual

1 Oktober 2025

Schneider QCGK3 Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3319 Manual

1 Oktober 2025

Schneider Altivar 312 VZ3V3103 Manual

1 Oktober 2025

Schneider SCTK30 Manual

1 Oktober 2025

Schneider Altivar 71 VW3A7201 Manual

1 Oktober 2025

Schneider OHBS Manual

1 Oktober 2025

Schneider Altivar 61 VW3A3502 Manual

1 Oktober 2025

Schneider Altivar 21 VW3A21101 Manual

1 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hendi 580035 Manual

3 November 2025

MSW -PTM-02 Manual

3 November 2025

ANCEL FX1000 Manual

3 November 2025

Extron RCP 401 Manual

3 November 2025

IFM E11847 Manual

3 November 2025

Ingenuity Easy Rinse Bather Manual

3 November 2025

ANCEL S2000 Manual

3 November 2025

ANCEL HD3600 Manual

3 November 2025

Hendi 550113 Manual

3 November 2025

Philips Series 5000 MG5942 Manual

3 November 2025