Siemens RDF600 Manual

Siemens Termostat RDF600

Læs gratis den danske manual til Siemens RDF600 (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Siemens RDF600, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CE1B3176.3en / 2012-08-29 Subject to change Siemens Building Technologies

Operating Instructions RDF600

RDF600 – the room thermostat that allows you to set the ideal room temperature you want.

The thermostat provides Comfort mode, Economy mode and Protection.

The fan operates either in automatic mode or at the selected speed when using manual mode.

You can either rely on the factory settings or make adjustments that suit your individual needs.

Change room temperature

+ -

Press + or - to increase or decrease the current room temperature setpoint for

Comfort mode. The thermostat changes to Comfort .

The setting range is from 5...40 °C, unless limited by parameters P09 and P10.

Adjust fan speed / fan mode

Press the button until you reach the desired fan mode.

In Auto mode, the fan speed is automatically selected by the thermostat and

depends on the setpoint and the actual room temperature. When the room

temperature has reached the setpoint, the fan is switched off (factory setting)

In manual mode the fan operates independently and always runs at the same

speed: Low, medium or high.

Low fan speed

Medium fan speed

High fan speed

For a single-speed fan, the mode can be changed between and .

Set the thermostat to Protection

Press the operating mode button several times until the display shows the

symbol to indicate that Protection is selected.

In Protection , only frost protection is active (factory setting = 8˚C), unless

your HVAC installer has adjusted the factory settings.

Changes by installer   Frost protection: ________ ˚C

 Heat protection: ________ ˚C

Set the thermostat to Economy mode

 

The thermostat can be set to Economy mode either via pressing the operating

mode button if enabled (see parameter P02), or via an external contact such

as window switch, key card switch etc.

If the external contact is activated the thermostat changes from Comfort mode or

Protection to Economy mode. Any operation by the user has no influence.

In Economy mode, the automatic fan control is active.

Note: If the thermostat is configured for manual heating / cooling changeover,

the Economy mode can not be selected via operating mode button .

Change from heating to cooling mode

The changeover between cooling and heating is done either automatically by a

heating / cooling changeover sensor or a remote changeover switch, or manually

by pressing the operating mode button . If the thermostat is configured for

cooling only or heating only, no changeover is possible (see parameter P01)

Display for automatic changeover or continuous heating/cooling:

Heating valve is open

Cooling valve is open

Display for manual changeover:

Thermostat is in heating mode

Thermostat is in cooling mode

Display

Operation and settings

Automatic fan

Low fan speed

Medium fan speed

High fan speed

ad locked

Fault indicator *

Condensation in the room*

Cooling demand / mode

Heating demand / mode

Electric heater active

Protection

Comfort

Economy

Measured room temperature,

setpoints and parameters

Symbol when actual room

temperature is displayed

Current time of day or

additional user information

Adjusting fan mode

- Automatic fan ( )

- Manual fan ( )

Adjusting operating mode

- Protection ( )

- Comfort ( )

- Economy ( )*

or in a system with manual changeover:

- Protection ( )

- Comfort heating ( )

- Comfort cooling ( )

Colder / Warmer

* if confi

ured b

our HVAC installe

CE1B3176.3en / 2012-08-29 Subject to change Siemens Building Technologies

Button lock

Press operating mode button for 3 seconds to lock or unlock the buttons if

manual button lock is configured (parameter P14 = 2).

The thermostat automatically locks the buttons 30 seconds after the last

adjustment if "Auto lock" is configured (P14 = 1).

The key symbol indicates locked buttons.

Reminder to clean filters

External faults

Commissioning (by qualified HVAC installer)

To adapt the thermostat to your system and optimize the control performance, a number

of control parameters can be adjusted. This can also be made during operation without

opening the thermostat.

Control sequence

Recalibrating the sensor

Note: Economy mode

The Economy setpoints are factory-set to 15 °C for heating and 30 °C for

cooling. Use parameters P11 and P12 to adjust the values.

Important: You can set these setpoints to OFF; the thermostat then is

inactive, i.e. no protective heating or cooling function. 



 Risk of frost!

Control parameters

Proceed as follows to change the most important control parameters:

(Your HVAC installer can set additional parameters)

+ / -

1. Set the thermostat to Protection

2. Press - and + simultaneously for a minimum of 4 seconds.

Release them and, within 2 seconds, press + again until "P01" is displayed.

3. Repeatedly press the + or – button to select the required parameter.

P01 P02 P08 P13

+- +

- -

3057z03

P14 -

-P12 +-

4. Press + and – simultaneously, the current value of the selected parameter starts to flash, allowing you to change

the value by repeatedly pressing + or –.

5. The next parameter is displayed when you press + and – again simultaneously.

6. Repeat steps 3 to 5 to display and change additional parameters.

7. 15 seconds after the last display or setting, all changes are saved and the thermostat will leave parameter entry

mode.

Para-

meter Description Factory setting Setting range 

P01 Control sequence

2-pipe: [0…3]

1 (Cooling only)

4-pipe: [2…4]

4 (Heating & Cooling)

0 = Heating only

1 = Cooling only

2 = Manual H or C

3 = Auto Changeover

4 = Heating & cooling

P02 Mode selection by user via operating mode button 1 (Protection,

Comfort)

1 = Protection, Comfort,

2 = Protection, Comfort,

Economy

P04 Selection of °C or °F 0 (°C) 0 = °C

1 = °F

P05 Sensor calibration 0.0 K – 3 ... +3 K

P06 Standard temperature display 0 (Room temp.) 0 = Room temperature

1 = Setpoint

P07 Additional user information 0 (no display) 0 = no display

1 = Temp in °C / °F

P08 Comfort basic setpoint 21 °C 5 ... 40 °C

P09 Minimum setpoint limitation in Comfort (WminComf) 5 °C 5 ... 40 °C

P10 Maximum setpoint limitation in Comfort (WmaxComf) 35 °C 5 ... 40 °C

P11 Setpoint of heating in Economy mode (WheatEco Eco) 15 °C OFF, 5 °C…Wcool

P12 Setpoint of cooling in Economy mode (WcoolEco Eco) 30 °C OFF, Wheat …40°C

P13 Electric heater in cooling mode ON OFF = Disabled

ON = Enabled

P14 Button lock

(Press operating mode button for 3 seconds to lock or

unlock the buttons)

0 (Disabled) 0 = Disabled

1 = Auto lock

2 = Manual lock

The control parameters displayed depend on the DIP switch settings made

 Please record all changes you make!

(All temperature settings can be made in increments of 0.5 K)

FIL This message reminds you to clean the filter on your HVAC equipment.

It will appear after  __________ "fan operating hours" and disappear when

the thermostat is set to Protection ( ).

This reminder must be configured by your HVAC installer.

AL1

AL2

This alarm message tells you an external alarm has occurred:

AL1 : ______________________

AL2 : ______________________

The alarms are configured by your HVAC installer

The thermostat can be used in systems either for heating only or cooling

only, manually selection of heating or cooling, or automatic heating / cooling

changeover. Depending on the selected application, the relevant modes are

available and can be adjusted by commissioning parameter P01 if needed.

The factory setting for 2-pipe application is "Cooling only", and for 4 pipe

application "Heating and Cooling"

If the room temperature displayed by the thermostat does not agree with the

temperature effectively measured (after min 1 hour of operation), the tem-

perature sensor can be recalibrated. With parameter P05 the temperature can

be adjusted by + or – 0.5 °C up to a maximum of + / - 3 °C.

Produkt Specifikationer

Mærke:	Siemens
Kategori:	Termostat
Model:	RDF600

Har du brug for hjælp?

Hvis du har brug for hjælp til Siemens RDF600 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Siemens Manualer

Siemens QAF64 Manual

28 December 2024

Siemens RDG100T Manual

15 Oktober 2024

Siemens DESIGO RXA Manual

5 Oktober 2024

Siemens REV33 Manual

3 Oktober 2024

Siemens RAA31 Manual

16 September 2024

Siemens REV100 Manual

2 September 2024

Siemens Landis & Staefa REV22RF Manual

1 September 2024

Siemens RDG160T Manual

1 September 2024

Siemens RDF600KN Manual

30 August 2024

Siemens REV23M Manual

30 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Daikin BRC1D528 Manual

11 August 2025

Carrier Infinity SYSTXCCITC01-B Manual

10 August 2025

Hager WXF315 Manual

9 August 2025

Hama 176592 Manual

9 August 2025

Eberle UTE 1002 Manual

7 August 2025

Eberle UTE 1012 Manual

7 August 2025

Eberle SSR-E 6905 Manual

7 August 2025

JUNG CD 500 Manual

7 August 2025

Levoit Aura Sensor LTM-AS041S-WUS Manual

6 August 2025

Perel CTH407 Manual

5 August 2025