Sightron S6 5-30x56 Manual

Sightron Ikke kategoriseret S6 5-30x56

Læs gratis den danske manual til Sightron S6 5-30x56 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Sightron S6 5-30x56, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Introduction to Sightron

Your New S6 Riflescope

Focusing your Riflescope

S6 5-30x56 SERIES

RIFLESCOPE

INSTRUCTIONS

Congratulations on the purchase of your new

Sightron S6 Series Riflescope.

Sightron is a leader in developing new products

for the outdoor enthusiast.

This instruction sheet is designed to provide you

with the proper fundamentals for using your

S6 Series Riflescope.

If you have any questions, please feel free to

www.sightron.com, or by phone at

+1-919-562-3000.

Before mounting your new Sightron S6 5-30x56

Series

Scope please check to make sure it is the

correct

model and includes the following

accessories:

1-Set of Front and Rear Lens Covers

1-Three-inch Sunshade

1-1.27 MM Allen wrench

1-2.0 MM Allen wrench

1-Lens Cloth

1-Instruction Sheet

1-CR2032 Battery for the illumination Switch

1- Reticle Chart

Mounting Your Riflescope

Your new scope has been optically centered at the

factory and superior performance will be obtained

with minimal adjustment.

Prior to sighting in your scope it is important to

know the windage and elevation adjustment

specifications of your particular scope model.

A general rule is the more the magnification the

less internal adjustment is available.

Once you have completed the eyepiece / diopter

adjustment, the next step is to turn the side focus

knob on the left side of the scope until the image

or target is clear. Now your scope is adjusted and

ready for shooting.

Note: The focus will need to be adjusted each

time the distance is changed.

Sighting in Your Gun

1. Place a 2 to 3 foot target at 50 to 100 yards

away. Using a bench rest, fire two shots while

aiming at the center of the bullseye.

While re-aiming at the bullseye adjust the reticle

to the bullets impact point by using the turret

adjustments and fire two more shots.

Your scope should now be close to point of aim.

Fire at the bullseye and make the necessary

final adjustments.

4. Adjusting the windage and elevation turret in

the direction of the arrow on the knob, it will

move the bullet impact in the direction indicated.

5. For best optical and mechanical performance

keep the windage and elevation travel as

centered as possible to allow for maximum

adjustment range for your model of riflescope.

Note: Most sight in problems are caused by

poor ring alignment.

Using your Illumination Reticle

To install the illumination battery, remove the

battery cap located at the end of the side focus

knob by rotating it counterclockwise.

Insert the CR2032 battery with the positive side

up and retighten finger tight.

Rotate the illumination switch to the required

setting for the lighting conditions.

Using your Internal Zero Stop

NOTE: The zero stop comes from the factory

set at the full range of elevation travel.

1. To set the zero stop, sight in the gun at the

desired range.

2. Loosen the three 2.0 MM hex screws from

the elevation turret and remove the turret.

3. Loosen the 1.27 MM hex screw on the Zero

Stop collar until it is loose.

4. The Zero Stop collar will then drop to meet

the main turret body.Turn the Zero Stop

clock wise until it stops.

5. Retighten the 1.27MM hex screw.

6. Retighten the three 2.0 MM hex screws on

elevation turret.

Once your scope is sighted in for the required

distance, loosen the three 2.0 MM hex screws.

Rotate the turret so the zero on the turret aligns

with vertical index mark on the revolution scale.

Retighten the three 2.0 MM hex screws.

Fi t Shotrs

First Adjustment

Adjust

reticle

to this

point

Battery Cap (CR2032)

Illumination Switch

Side Focus Knob

Resetting your Windage and

Elevation Turrets

Full Travel

Position

Zero Stop Collar

Zero Stop

Locked Position

Ocu ar Lel ns

Di pt justi Rio er Ad ng ng

Elevation Adjusting Knob

Windage

Adj

Zoom Ring Lever

(Removeable)

Ba ry C 2 2)tte ap (CR 03

Parallax and Illumination

Adjusting Knob

Objective Lens

CAUTION: ALWAYS ENSURE YOUR

WEAPON IS UNLOADED PRIOR TO MOUNTING

YOUR SCOPE.

USE EYE AND HEARING PROTECTION AND

FOLLOW PROPER SAFETY RULES WHEN

HANDLING OR FIRING YOUR WEAPON.

Place both rings on your mount base or receiver,

and tighten. Remove the top half of the rings

and place the riflescope in the bottom half of

the rings.

Once you have determined proper ring spacing

and eye relief, align the reticle with a vertical

line preferably a plumb line.

Tighten the top half of the rings to between

15 to 18 inch pounds or

169 to 203 Newton

Centimeters and adjust the

diopter or eye piece

focus so the reticle is crisp

and clear.

Note: The only purpose of the diopter is to focus

the reticle sharp and clear.

Produkt Specifikationer

Mærke:	Sightron
Kategori:	Ikke kategoriseret
Model:	S6 5-30x56

Har du brug for hjælp?

Hvis du har brug for hjælp til Sightron S6 5-30x56 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Sightron Manualer

Sightron SIII PLR Manual

10 November 2025

Sightron SIII Manual

6 Juli 2025

Sightron SII Manual

6 Juli 2025

Sightron S1 G2 Manual

5 Juli 2025

Sightron S6 5-30x56 Manual

2 April 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Velux TGR 010 Manual

7 Januar 2026

LG PREMTC00U Manual

7 Januar 2026

LG PREMTBVC2 Manual

7 Januar 2026

Reelcraft WCH80001 Manual

7 Januar 2026

Panduit CT-1015 Manual

7 Januar 2026

WAC Lighting MT4LD216NE Manual

7 Januar 2026

WAC Lighting HTK-703 Manual

7 Januar 2026

Verkada AC42 Manual

7 Januar 2026

Panduit FC2ZO-24-10AF Manual

7 Januar 2026

Vaxcel T0678 Manual

7 Januar 2026