Skan Holz Alicante 1 Manual

Skan Holz Ikke kategoriseret Alicante 1

Læs gratis den danske manual til Skan Holz Alicante 1 (19 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Skan Holz Alicante 1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/19

Alicante 1 380 x 513cm

Important information

We are pleased that you have chosen a product of SKAN HOLZ.

Please check the construction set for completeness using the position list in good time before starting con-

struction or commissioning your construction team. If individual parts are defective or missing, we will deliver

these as quickly as possible. However, we cannot refund the costs for any resulting construction delays to a

construction company.

Please understand that we cannot assume any guarantee for the following defects:

- incorrect storage before assembly

- incorrect anchoring with the ground or inadequate foundation (foundation according to statics)

- damage due to erection errors, e. g. the house is not level or not right-angled

- damage through a higher level of snow burden than statically envisaged. Recommendation: lad relief of

the roof by removing the snow layer

- storm damage (insurance cases) or violent destruction

- damage through any alteration to the design by the client

- natural formation of cracks, branch holes, twisting, decolouration or similar modification (natural

process; has no influence on the statics)

Storage information until construction:

- store pallet on a level and dry surface.

- ; wood can warp drastically in a looseProtect from exposure to sunlight and the influences of weather

condition!

Maintenance tips:

The wood is untreated. Accordingly, regular, protective coating is absolutely necessary!

Please observe the attached information sheet “Care instructions/Colour treatment”.

General tips and refers to:

The packaging foil to keep moisture out of the house. It is laid according to the ground area of thecan be used

house under the main bearing.

Given that the roof is constantly exposed to the weather, a covering with only one layer of roofing paper will not

be enough over the long-term. An additional covering with bitumen shingles, alternatively with a material of at

least equivalent quality, must follow.

Foundation according to the structural calculations (not included in the scope of delivery): concrete C25/30,

each 2 Ø 12 top and bottom, brace mat R188A (alternatively brace Ø 6/20cm). Anchoring of the floor beams

(in the building) on the strip foundation using bolts M12, e < 60cm. The base bearings in the storeroom of the

house must be entirely flush.

The thread rods to secure the house against storm are secured at the top with a washer and a nut, from below

with a washer, spring and nut to tighten the upper nut of the thread rod without any problem, the spring at the

bottom should be pressed upwards with the thread rod. so that theThe spring may only be tightened slightly

house can work at the top. The . Even afterprojecting ends of the thread rods have to be cut off at the top

the house has been completed, attention must always be paid to the fact that the thread rods are not seated on

the floor as otherwise when it is dry, gaps can arise and the roof is pressed upwards. the thread rods canTip:

also be pushed subsequently into the bores. You have to make sure that and that theseeach plank has a bore

are free and .not blocked by shavings or similar

In case of varying weather conditions, the wood alters in height (due to 'working'). To avoid the formation of joints,

the planks of the house may not, for example, be joined as thento one another through several block planks

the wood can no longer expand.

The since thedoor and window frames may not be bolted to the wall above the first supporting plank

individual bolts will work in height. If the door does not close correctly, this can be readjusted by rotating the

hinges in the door leaf and door frames.

551606

380 x 513cm

1 x 28-26-001

547cm

1 x 28-26-003

547cm

1 x 28-26-002

547cm

3 x H19/120-00

65cm

100 x H19/119-01

130cm

100 x H19/119-01

90cm

4 x H16/58-00

273,5cm

33 x H19/121-01

143,5cm

16 x H20/20-04

200cm

1 x H20/46-00

78,4cm

3 x H58/58-03

379,5cm

2 x H28/70-00

323cm

2 x H58/58-03

363cm

7 x H16/58-00

66,5cm

1 x H28/70-00

177,5cm

1 x H58/58-03

199,5cm

Produkt Specifikationer

Mærke:	Skan Holz
Kategori:	Ikke kategoriseret
Model:	Alicante 1

Har du brug for hjælp?

Hvis du har brug for hjælp til Skan Holz Alicante 1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Skan Holz Manualer

Skan Holz Varberg 1 Manual

31 Maj 2025

Skan Holz Alicante 2 Manual

31 Maj 2025

Skan Holz Knut Manual

30 Maj 2025

Skan Holz Almelo Manual

30 Maj 2025

Skan Holz Varberg 2 Manual

30 Maj 2025

Skan Holz Grunewald Manual

30 Maj 2025

Skan Holz Breda 2 Manual

30 Maj 2025

Skan Holz Basel 1 Manual

30 Maj 2025

Skan Holz Esbjerg 3 Manual

30 Maj 2025

Skan Holz Narvik Manual

30 Maj 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Salton MP1206 Manual

31 August 2025

TensCare Sports TENS 2 Manual

31 August 2025

Pardini K58 Manual

31 August 2025

Salton SCG-4 Manual

31 August 2025

Salton JK-1103 Manual

31 August 2025

Salton WC-2040 Manual

31 August 2025

Salton WC-2070 Manual

31 August 2025

Salton SP1963 Manual

31 August 2025

Gram EFI 8060-91 B Manual

31 August 2025

Analog Way Orchestra² Manual

31 August 2025